ACU-RITE 592TXR User manual

Instruction Manual
Temperature & Humidity Sensor
model 06002 / 592TXR
Printed in China
06002M INST 082516
It’s More than Accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
Features & Benets
4
3
2
1
5
SENSOR
1. Integrated Hanger
For easy placement.
2. Wireless Signal Indicator
Flashes when data is being
wirelessly transmitted.
3. Battery Compartment
4. A-B-C Switch
5. Battery Compartment Cover
SETUP
Set the A-B-C Switch
The A-B-C switch is located inside
the battery compartment. It can be
set to A, B or C.
NOTE: If being used with a
companion product that has an
A-B-C channel, you must select the
same letter choice for both the
sensor and the product it is being
paired with in order for the units to
synchronize.
Install or Replace Batteries
AcuRite recommends high quality
alkaline or lithium batteries in
the sensor for the best product
performance. Heavy duty or
rechargeable batteries are not
recommended.
Sensor Setup
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.
Such modications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the
Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights
are the property of their respective owners. AcuRite uses patented technology.
Visit www.AcuRite.com/patents for details.
1
2
The sensor requires lithium
batteries in low temperature
conditions. Cold temperatures
can cause alkaline batteries
to function improperly. Use
lithium batteries in the sensor for
temperatures below -4ºF / -20ºC.
1. Slide off the battery
compartment cover.
2. Insert 2 x AA batteries into
the battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.

Specications
TEMPERATURE RANGE -40°F to 158°F; -40°C to 70°C
HUMIDITY RANGE 1% – 99% RH (relative humidity)
BATTERY REQUIREMENTS 2 x AA alkaline or lithium batteries
WIRELESS RANGE 330ft / 100 m depending on home construction materials
OPERATING FREQUENCY 433MHz
32
A-B-C Switch
A B C
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of the sensor is critical to the accuracy and performance of this product.
Sensor Placement
The sensor is water-resistant and is designed for general indoor or
outdoor use, however, to extend its life place the sensor in an area
protected from direct weather elements.
Hang the sensor using the integrated hang hole or hanger, or by using
string (not included) to hang it from a suitable location, like a well covered
tree branch. The best location is 4 to 8 feet above the ground with
permanent shade and plenty of fresh air to circulate around the sensor.
Important Placement Guidelines
• To ensure accurate temperature measurement, place sensor out of direct
sunlight and away from any heat sources.
• Sensor must be within 330 ft (100 m) of companion unit (not included).
• To maximize wireless range, place sensor away from large metallic items, thick
walls, metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place sensor at least 3 ft (0.9 m) away
from electronic devices (TV, computer, microwave, radio, etc.).
For more information, visit our Knowledge Base at http://www.AcuRite.com/kbase
Limited 1-Year Warranty
AcuRite is a wholly owned subsidiary of Chaney
Instrument Company. For purchases of AcuRite
products, AcuRite provides the benets and services set
forth herein. For purchases of Chaney products, Chaney
provides the benets and services set forth herein.
We warrant that all products we manufacture under this
warranty are of good material and workmanship and, when
properly installed and operated, will be free of defects for a
period of one year from the date of purchase.
Any product which, under normal use and service, is proven
to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by us, and at our sole
option, be repaired or replaced by us. Transportation costs and
charges for returned goods shall be paid for by the purchaser.
We hereby disclaim all responsibility for such transportation
costs and charges. This warranty will not be breached, and we
will give no credit for products which have received normal
wear and tear not affecting the functionality of the product,
been damaged (including by acts of nature), tampered,
abused, improperly installed, or repaired or altered by others
than our authorized representatives.
Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). If we determine that repair
or replacement is not feasible, we may, at our option, refund
the amount of the original purchase price.
THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY
FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES
OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN
ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
We expressly disclaim all liability for special, consequential,
or incidental damages, whether arising in tort or by contract
from any breach of this warranty. Some states do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
We further disclaim liability from personal injury relating to
our products to the extent permitted by law. By acceptance of
any of our products, the purchaser assumes all liability for the
consequences arising from their use or misuse. No person, rm
or corporation is authorized to bind us to any other obligation
or liability in connection with the sale of our products.
Furthermore, no person, rm or corporation is authorized
to modify or waive the terms of this warranty unless done in
writing and signed by a duly authorized agent of ours.
In no case shall our liability for any claim relating to our
products, your purchase or your use thereof, exceed the
original purchase price paid for the product.
Applicability of Policy
This Return, Refund, and Warranty Policy applies only to
purchases made in the United States and Canada. For
purchases made in a country other than the United States or
Canada, please consult the policies applicable to the country in
which you made your purchase.
Additionally, this Policy applies only to the original purchaser
of our products. We cannot and do not offer any return,
refund, or warranty services if you buy products used or from
resale sites such as eBay or Craigslist.
Governing Law
This Return, Refund, and Warranty Policy is governed by the
laws of the United States and the State of Wisconsin. Any
dispute relating to this Policy shall be brought exclusively in the
federal or State courts having jurisdiction in Walworth County,
Wisconsin; and purchaser consents to jurisdiction within the
State of Wisconsin.
Customer Support
AcuRite customer support is committed to providing you with best-in-class service.
For assistance, please have the model number of this product available and contact
us in any of the following ways:
[phone]
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com
IMPORTANT PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
Visit us at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
1
Install Batteries
2 AA batteries
2
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment that will not be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.

Instruction Manual
CONTENTS
Unpacking Instructions ........... 2
Package Contents .................. 2
Product Registration ............... 2
Features & Benets................. 3
Display Setup ........................ 7
Placement Guidelines ............. 8
Expand the System................. 9
Using the Weather Station.....10
Troubleshooting ....................15
Care & Maintenance.............16
Specications........................17
FCC Information ...................17
Customer Support .................18
Warranty..............................18
High Resolution
Weather Station Display
model 06027
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Questions? Contact Customer Support at
[phone] or visit www.AcuRite.com.
This product requires at least one AcuRite Monitor or Sensor
(sold separately) to be operational.

2
Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Remove the protective lm that is applied to the LED screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display with Tabletop Stand
2. Power Adapter
3. Mounting Bracket
4. Instruction Manual
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com
IMPORTANT PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

3
Features & Benets
Weather Overview Dashboard
1. Alarm ON Indicator
Indicates alarm is activated to emit an
audible alert when conditions exceed
your presets (see page 10).
2. Indoor Conditions or
How-to-Dress Character
Select viewing preference during setup
(see page 12).
3. Clock
4. Current Outdoor Humidity
Arrow icon indicates direction
humidity is trending.
5. Weather Forecast and Indoor
Humidity Messages
Text readout of weather forecast.
Displays humidity alerts when indoor
conditions are too high or low
(see page 13).
6. Day Of The Week
7. Date
8. Weather Forecast and
Current Conditions
Self-Calibrating Forecasting pulls data
from your sensor to generate your
personal forecast. Illustrates current
conditions and automatically adjusts
based on time of day and season.
9. Current Indoor Temperature
Arrow indicates direction
temperature is trending.
10. Messages
Weather information and alert
messages (see page 13).
11. Outdoor Sensor Signal Strength
11
1
10
9
8
2
3
65 74

4
1. Humidity Level Indicator
Indicates a high, low or ideal
humidity comfort level (see page 14).
2. Daily High & Low
Temperature Records
Lowest and highest temperature
recorded since midnight.
3. Current Indoor Humidity
Arrow indicates direction humidity
is trending.
4. Daily High & Low
Humidity Records
Lowest and highest humidity recorded
since midnight.
5. Recommendations
Indoor comfort recommendations
based on outdoor conditions
(see page 14).
6. Current Indoor Temperature
Arrow indicates direction temperature
is trending.
Features & Benets
Indoor Overview Dashboard
weather overview
12:35 pm TUE 10/25
indoor
indoor comfort:
high humidity!
open windows
it’s mild outside
72
61
61
7368
33
ºF
%
indoor overview
1
3
4
2
5
6

5
Features & Benets
All Locations Dashboard
1. Wireless Signal Strength
Signal strength detected for the
external Monitor or Sensor (sold
separately) that is reporting data for
the location.
2. Low Battery Indicator
For the product that is reporting data
for the corresponding location.
3. Alarm ON Indicator
Indicates alarm is activated to emit an
audible alert when conditions exceed
your presets (see page 10).
4. Water Detector Reading
Indicates Water Detector (sold
separately) data.
5. Wired Sensor Indicator
Indicates a Wired Sensor (sold
separately) is reporting data to the
display.
6. Humidity Reading
Humidity reading reported by the
product that is installed in the location
indicated.
7. Temperature Reading
Temperature reading reported by
the product that is installed in the
location indicated.
8. Location Name
Label your data readings by location
name (see page 11).
7
6
5
7
12:35 pm TUE 10/25
All Locations
press for multi-sensor setup
46
46ºF
Outdoor
%
41
72ºF
Display
%
sensor:
24
68ºF
Baby’s Room
%
sensor: No Water Detected
29
58ºF
Basement
%
87º 23%
1
2
8
34
5
6

6
DISPLAY BACK
1. Plug-in for Power Adapter
2. Display Stand
Snaps in for tabletop use.
3. Mounting Bracket
For easy wall mounting.
DISPLAY FRONT
4. Button
For menu access and setup
preferences.
5.
V
Button
For setup preferences and cycling
through messages on the Weather
Overview dashboard.
6. Button
Press to view a different dashboard.
7.
T
Button
For setup preferences and cycling
through messages on the Weather
Overview dashboard.
8. Button
For setup preferences.
1
45 6 7 8
Features & Benets
Display
2
3

7
Display Setup
SETUP
1Install External Monitor or Sensor Batteries
BEFORE powering on the display, install batteries for all external Monitors
and/or Sensors (sold separately) that you would like to synchronize with
the display.
Plug Power Adapter
into Electrical Outlet
2
NOTE: If pairing more than one wireless sensor (model 06002 or 06044) with the display,
the A-B-C channel must differ between each sensor. Verify that each sensor has a different
channel selected by following the instructions in the corresponding sensor manual.
A-B-C
Channel
A-B-C
Channel

8
Settings
After powering on for the rst time, the display will automatically enter setup
mode. Follow the on-screen instructions to set up the display.
To adjust the currently selected item, press and release the “T” or “
V
“
buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button again to adjust
the next preference. The preference set order is as follows:
TIME ZONE (PST, MST, CST, EST, AST, HAST, AKST)
AUTO DST (Daylight Saving Time YES or NO)*
CLOCK HOUR
CLOCK MINUTE
MONTH
DATE
YEAR
PRESSURE UNITS (inHg or hPa)
TEMPERATURE UNITS (ºF or ºC)
AUTO DIM (YES or NO)**
AUTO CYCLE (OFF, 10 sec., 30 sec., 60 sec., 2 min.)
INDOOR READINGS or HOW-TO-DRESS CHARACTER***
ALERT VOLUME
*If you live in an area that observes Daylight Saving Time, DST should be set to YES,
even if it is not currently Daylight Saving Time.
**For more information see page 11, under “Display”.
***For more information see page 12, under “How-to-Dress Character”.
Enter setup mode at any time by pressing the “ ” button to access the menu,
then navigate to “Setup” and press and release the “ ” button.
Placement for Maximum Accuracy
AcuRite products are sensitive to surrounding environmental conditions. Proper
placement is critical for accuracy and performance.
Display Placement
Place the display in a dry area free of dirt and dust. Display stands
upright for tabletop use and is wall-mountable.
Important Placement Guidelines
• To ensure accurate temperature measurement, place product out of direct
sunlight and away from any heat sources or vents.
• Display and add-on Monitors/Sensors must be within 330 feet (100 m) of
each other.
• To maximize wireless range, place product away from large metallic items, thick
walls, metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place product at least 3 feet (.9 m) away from
electronic devices (TV, computer, microwave, radio, etc.).

9
Expand the System
The display features built-in sensors for measuring temperature and humidity at
its location. The display can be expanded to track additional conditions by using
compatible Monitors and Sensors (optional; sold separately). Add up to 3 Monitors
and Sensors to observe conditions in additional locations within 330 ft (100 m).
Compatible Monitors and Sensors are available at: www.AcuRite.com
Monitor + Wired Sensor Perfect for:
• Basement ooding
• Roof leaks
• Leaky appliances
• Sump pump failure
• Track high or low water level
• Indoor pool, spa, pond or fountain
temperature
• Prevent frozen pipes
• Seeding, potting and gardening
• Monitor conditions in hard to reach places
(attic, basement, etc.)
• Pet areas
• Evaluate heating and cooling efciency and
coverage in your home
• Monitor conditions in nursery or child’s room
Water Detector
Model 06010
Liquid & Soil
Temperature
Sensor
Model 06011
Spot Check
Temperature &
Humidity Sensor
Model 06012
32
18
Compatible Monitors Perfect for:
• Outdoor applications
• Indoor applications
• Indoor and outdoor applications
Temperature &
Humidity Monitor
Model 00275
Room Monitor
Model 00276
32
18
Temperature &
Humidity Sensor
Model 06002
Temperature &
Humidity Sensor
Model 06044
• Indoor applications
NOTE: During setup, an image of model
06002 will be shown.

10
Using the Weather Station
OPERATION
Menu
Records
Display
Monitors
Setup
Factory Reset
Units
Alarms
Calibrate
press to exit menu
15
26
37
4 8
Navigate to the main menu at any time by pressing the “ ” button. From the
main menu, you can view records, set alarms, setup additional monitors and more.
1. Records
Access the “Records” sub-menu to view high and low values recorded for
each location by date and view trends for each of the monitor’s readings on
a graphic chart.
2. Alarms
Access the “Alarms” sub-menu to set and edit alarm values.
3. Setup
Access the “Setup” sub-menu to enter the initial setup process.

11
4. Display
Access the “Display” sub-menu to adjust display settings (brightness,
contrast, tint), display mode (screen cycle) and backlight (auto dim).
When auto dim mode is activated in display setup, the backlight
automatically dims the brightness based on the time of day and year.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.
MARCH 11- NOVEMBER 4 6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 30% brightness
NOVEMBER 5 - MARCH 10 7:30 a.m. - 7:00 p.m.= 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness
5. Monitors
Access the “Monitors” sub-menu to add, remove or rename a monitor
location. Note: The monitor is labeled “OUTDOOR” will supply information
for the forecast and the Weather Overview dashboard. Only one monitor
can be labeled “OUTDOOR.”
AQUARIUM BEDROOM 3
ANIMALS BEDROOM 4
CELLAR
COOLER
DINING RM
FAMILY RM
FREEZER
FRIDGE
GARDEN
ATTIC
BABY’S ROOM
BATHROOM 3
BASEMENT
BATHROOM
BATHROOM 2
BEDROOM
BEDROOM 2
GUEST ROOM
HOT TUB
HUMIDOR POOL
PORCH
SPA
STORAGE
SUMP PUMP
UPSTAIRS
UTILITY
WINE
KITCHEN
LAUNDRY
LIVING RM
MASTER BR
MUSIC RM
NURSERY
OFFICE
OTHER
GARAGE
OUTDOOR
Location Names
6. Units
Access the “Units” sub-menu to change measurement units for barometric
pressure (hPa, inHg) and temperature (°F, °C).
7. Calibrate
Access the “Calibrate” sub-menu to adjust display or monitor/sensor data.
First, select a location from the on-screen list. Second, select the reading you
wish to calibrate (temperature, humidity, pressure). Lastly, follow the
on-screen prompts to adjust the value.
8. Factory Reset
Access the “Factory Reset” sub-menu to revert the display back to factory
defaults. Follow the on-screen prompts to perform the reset.

12
Weather Overview Dashboard
Weather Forecast
AcuRite’s patented Self-Calibrating Forecasting provides your personal forecast
of weather conditions for the next 12 to 24 hours by collecting data from
a sensor in your backyard. It generates a forecast with pinpoint accuracy -
personalized for your exact location.
Self-Calibrating Forecasting uses a unique algorithm to analyze changes in
pressure over a time period (called Learning Mode) to determine your altitude.
After 14 days, the self-calibrated pressure is tuned in to your location and the
unit is ready for superior weather prediction.
Note: To forecast precipitation accurately a weather-resistant Monitor or
Sensor (sold separately) must be placed outdoors and its location name must
be set to OUTDOOR.
Moon Phase
The moon phase is displayed between 7:00p.m. to 5:59a.m. when conditions
allow for moon visibility. The phases of the moon are conveyed through simple
lunar phase icons:
FULL
NEW WAXING
CRESCENT
WANING
CRESCENT
1ST
QUARTER
3RD
QUARTER
How-to-Dress Character
The How-to-Dress Character includes 22 different weather recommendations
based on the weather forecast. If the How-to-Dress Character is the option
selected during setup, the character icon will be shown in place of indoor
readings on the dashboard.
hat
scarf
gloves
heavy coat
long pants
boots
hat
gloves
light jacket
long pants
shoes
sweatshirt
long pants
shoes
t- shirt
long pants
shoes
sunglasses
t-shirt
shorts
shoes
COLDER MILD WARMER

13
Messages
This display shows real-time weather information and alert messages on the
Weather Dashboard. Manually cycle through all available messages by
pressing the “T” or “ “ buttons while viewing the Weather Overview
dashboard.
Default messages are pre-loaded as follows:
BAROMETER Xx.xx AND RISING 30 DAYS HIGH TEMPERATURE RECORDED
BAROMETER Xx.xx AND STEADY 30 DAYS LOW TEMPERATURE RECORDED
BAROMETER Xx.xx AND FALLING ALL TIME HIGH TEMPERATURE RECORDED
WARMEST DAY THIS WEEK ALL TIME LOW TEMPERATURE RECORDED
WARMEST DAY THIS MONTH 24 HOUR TEMPERATURE CHANGE
WARMEST DAY THIS YEAR INDOOR HUMIDITY OK
COLDEST DAY THIS WEEK INDOOR HUMIDITY HIGH
COLDEST DAY THIS MONTH INDOOR HUMIDITY LOW
COLDEST DAY THIS YEAR NEW LOW TEMPERATURE RECORD
HEAT INDEX NEW HIGH TEMPERATURE RECORD
WIND CHILL SENSOR BATTERIES LOW
IT FEELS LIKE ??? OUTSIDE DISPLAY BATTERIES LOW
7 DAYS HIGH TEMPERATURE RECORDED CAUTION HEAT INDEX IS...
7 DAYS LOW TEMPERATURE RECORDED CAUTION WIND CHILL IS...
Indoor Humidity Messages
When the indoor humidity (measured by the display’s built-in humidity sensor)
is too high (above 60%) or low (below 30%) for more than 24 hours, a
recommendation is displayed on the Weather Dashboard (shown below).
Note: Humidiers and dehumidiers can be purchased from home centers.
Indoor Humidity is High!
Run a Dehumidifier
Indoor Humidity is Low!
Run a Humidifier

14
Indoor Overview Dashboard
Humidity Level Indicator
Indoor humidity is measured by the
display’s built-in humidity sensor. Humidity
is shown with a simple Humidity Level
Meter and text readout on the Indoor
Overview dashboard.
Recommendations
The Indoor Overview dashboard provides you with
recommendations based on outdoor conditions.
Open Windows
It’s Mild Outside
Recommendation shown if outdoor temperature is
between 60ºF - 76ºF (16ºC - 24ºC) and outdoor
humidity is between 33% - 65%.
Close Windows
It’s Too Cold Outside
Recommendation shown if outdoor temperature is less
than 60ºF (16ºC) and outdoor humidity is less than 32%.
It’s Too Warm Outside
Recommendation shown if outdoor temperature is
higher than 76ºF (24ºC) and outdoor humidity is less
than 55%.
It’s Humid Outside
Recommendation shown if outdoor temperature is
higher than 80ºF (27ºC) and outdoor humidity is
higher than 75%.
51-60%
indoor comfort
ideal humidity
71-80%
indoor comfort
high humidity
61-70%
indoor comfort
high humidity
81-90%
indoor comfort
high humidity
91-100%
indoor comfort
high humidity
41-50%
indoor comfort
ideal humidity
31-40%
indoor comfort
ideal humidity
0-10%
indoor comfort
low humidity
11-20%
indoor comfort
low humidity
21-30%
indoor comfort
low humidity

1515
Problem Possible Solution
No reception
no bars
If the wireless signal indicator shows no bars:
• Relocate the display and/or synced Monitor/Sensor
(if applicable). The products must be within 330 ft
(100 m) of each other.
• Make sure products (display, Monitors, Sensors) are
placed at least 3 feet (.9 m) away from electronics
that may interfere with the wireless communication
(such as TVs, microwaves, computers, etc).
• Use standard alkaline batteries (or lithium batteries
in Monitors and Sensors when temperature is below
-4ºF/-20ºC). Do not use heavy duty or rechargeable
batteries.
Note: It may take a few minutes for display and
sensor to synchronize after batteries are replaced.
Temperature is
showing dashes
Dashes in the temperature reported by a Monitor/
Sensor is generally an indication of wireless interference
between the sensor and display.
1.Remove the Monitor/Sensor location from the display.
2.Re-add Monitor/Sensor to an available location on
display (see page 11).
Inaccurate forecast
• Weather Forecast icon predicts conditions for the next
12 to 24 hours, not current conditions.
• Verify at least one weather-resistant Monitor/Sensor
is placed outdoors with the location name set to
OUTDOOR. This is required for full weather forecast
functionality.
• Allow product to run continuously for 33 days.
Powering down or resetting the display will restart
Learning Mode. After 14 days, forecast should be
fairly accurate, however Learning Mode calibrates for
a total of 33 days.
Inaccurate temperature
or humidity
• Verify the product that is reporting an inaccurate
temperature reading is placed out of direct sunlight and
away from any heat sources or vents (see page 8).
• Verify the product that is reporting an inaccurate
humidity reading is positioned away from moisture
sources (see page 8).
Display screen
not working
• Check that the power adapter is plugged into the
display and an electrical outlet.
Troubleshooting

1616
Problem Possible Solution
Sensor not recognized
If the Home Environment Display is being used with
more than one Temperature & Humidity Sensor (models
06002 or 06044), the A-B-C channels must differ
between each sensor.
1. Bring the display and wireless sensors together and
position them side-by-side.
2. Remove the power adapter from the display.
3. Verify that each sensor has a different A-B-C
channel selected.
• Model 06002 - Locate the A-B-C switch inside the
battery compartment to adjust channel setting.
• Model 06044 - Locate the A-B-C button on the back
of the sensor to adjust channel setting (indicated on
sensor display).
4. Re-install sensor batteries (if applicable).
5. Plug in display’s power adapter.
Note: It may take a few minutes for the display and
sensor(s) to synchronized after batteries are replaced.
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
[phone] for assistance.
Care & Maintenance
Display Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.

17
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.
Such modications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
DISPLAY’S BUILT-IN
TEMPERATURE SENSOR
RANGE
32ºF to 122ºF; 0ºC to 50ºC
DISPLAY’S BUILT-IN
HUMIDITY SENSOR RANGE 1% to 99% RH
OPERATING FREQUENCY 433 MHz
POWER 5vdc power adapter
DATA REPORTING Display Data: 60 second updates
Specications

18
Customer Support
AcuRite customer support is committed to providing you with best-in-class
service. For assistance, please have the model number of this product
available and contact us in any of the following ways:
[phone]
Visit us at www.AcuRite.com
► Installation Videos ► Register your Product
► Instruction Manuals ► Support User Forum
► Replacement Parts ► Submit Feedback & Ideas
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com
IMPORTANT PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
Limited 1-Year Warranty
AcuRite is a wholly owned subsidiary of Chaney
Instrument Company. For purchases of AcuRite
products, AcuRite provides the benets and services set
forth herein. For purchases of Chaney products, Chaney
provides the benets and services set forth herein.
We warrant that all products we manufacture under this
warranty are of good material and workmanship and, when
properly installed and operated, will be free of defects for a
period of one year from the date of purchase.
Any product which, under normal use and service, is proven
to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by us, and at our sole
option, be repaired or replaced by us. Transportation costs and
charges for returned goods shall be paid for by the purchaser.
We hereby disclaim all responsibility for such transportation
costs and charges. This warranty will not be breached, and we
will give no credit for products which have received normal
wear and tear not affecting the functionality of the product,
been damaged (including by acts of nature), tampered,
abused, improperly installed, or repaired or altered by others
than our authorized representatives.
Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). If we determine that repair
or replacement is not feasible, we may, at our option, refund
the amount of the original purchase price.
THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY
FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES
OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN
ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
We expressly disclaim all liability for special, consequential,
or incidental damages, whether arising in tort or by contract
from any breach of this warranty. Some states do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
We further disclaim liability from personal injury relating to
our products to the extent permitted by law. By acceptance of
any of our products, the purchaser assumes all liability for the
consequences arising from their use or misuse. No person, rm
or corporation is authorized to bind us to any other obligation
or liability in connection with the sale of our products.
Furthermore, no person, rm or corporation is authorized
to modify or waive the terms of this warranty unless done in
writing and signed by a duly authorized agent of ours.
In no case shall our liability for any claim relating to our
products, your purchase or your use thereof, exceed the
original purchase price paid for the product.
Applicability of Policy
This Return, Refund, and Warranty Policy applies only to
purchases made in the United States and Canada. For
purchases made in a country other than the United States or
Canada, please consult the policies applicable to the country in
which you made your purchase.
Additionally, this Policy applies only to the original purchaser
of our products. We cannot and do not offer any return,
refund, or warranty services if you buy products used or from
resale sites such as eBay or Craigslist.
Governing Law
This Return, Refund, and Warranty Policy is governed by the
laws of the United States and the State of Wisconsin. Any
dispute relating to this Policy shall be brought exclusively in the
federal or State courts having jurisdiction in Walworth County,
Wisconsin; and purchaser consents to jurisdiction within the
State of Wisconsin.