Adaptec 9110G User manual

AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
R
Installation Guide
AHA-1640
Micro Channel-to-SCSI Host Adapter

1
AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Installation Checklist
Be sure to complete these steps when you install
your AHA™-1640 Micro Channel®-to SCSI host
adapter. Check each item before you turn ON the
power to your computer:
1If you are using internal SCSI devices, connect the
50-pin internal SCSI cable to the host adapter
with proper pin-1 orientation.
2Seat the AHA-1640 host adapter firmly in an
available 16-bit slot.
3Assign correct SCSI addresses to all SCSI devices.
Assign SCSI ID 0 to the boot SCSI disk drive.
Assign SCSI ID 1 to the second SCSI disk drive, if
there is one.
4Select the correct operating modes on all attached
SCSI devices. Refer to the documentation for each
device.
5Set termination correctly on the AHA-1640 host
adapter and attached SCSI devices. Leave the ter-
minators installed if either an internal or an exter-
nal SCSI cable is attached to the host adapter.
Remove terminators if both an internal and an
external SCSI cable are attached.
6Check all external SCSI devices to be sure they are
properly installed and cabled.
Host Adapter Configuration
You must load initialization parameters into the host
computer’s CMOS RAM when you first install the
AHA-1640 host adapter. You must also update the
initialization parameters whenever you make other
host adapter configuration changes or when you
replace the computer’s standby battery. The host
adapter is automatically initialized with these
parameters every time you boot your computer.
The computer reads the initialization parameters
from the Adapter Descriptor File (ADF)1, which is
1 The actual file name of the ADF is
@0f1f.adf .
1
2

2
AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
usually included on the System Reference Diskette
(SRD). Follow these steps if the ADF is not on the
SRD:
1Make a copy of the SRD.
2Copy the ADF from an AHA-1640 Configuration
Diskette to the copy of the SRD.
You cannot use the original copy of the SRD,
because it is probably write-protected.
Note: If you do not have the ADF, you can
download it free of charge from Adaptec’s
Bulletin Board Service (BBS). The BBS tele-
phone number is listed on page 4.
Follow these steps to load the initialization parame-
ters into CMOS RAM after you have installed the
host adapter. You may need a special configuration
if you install more than one AHA-1640 host adapter.
1Insert the copy of the SRD in floppy drive Aand
close the drive door.
2Turn ON the power to the computer. If the power
is already ON, reboot the computer by pressing
the Del key while holding down the Ctrl and Alt
keys.
After the computer has booted, an Error 165 mes-
sage (Invalid Configuration Information) may
appear on the screen. This occurs when the com-
puter detects the newly-installed host adapter.
3Some SRD programs ask you in the error text if
you want the computer to perform an automatic
configuration.
aIf the SRD allows automatic configuration,
press the indicated key and wait until the con-
figuration is completed. Then continue with
step 7.
bIf the SRD does not allow automatic configu-
ration, press the indicated key to load the SRD
files. A menu appears when the files have
been loaded.

3
AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
4Select the menu option to set the configuration
parameters from the SRD. Another menu appears
when this process is completed.
5Select the menu option to control or perform the
configuration process automatically.
The program analyzes the ADF and selects
address spaces and parameter values that do not
conflict with values already in use. Then it loads
the values into CMOS RAM. A message appears
when the automatic configuration is complete.
6Press the indicated key to continue. The host
adapter is now ready for normal operation.
7Install the operating system software and boot
your computer.
If you remove the AHA-1640 host adapter from your
computer in the future, you must run automatic con-
figuration again to update the parameters.
The following table lists the values that should be
entered for various AHA-1640 configuration
options. Some of the option values vary, depending
on whether you boot your computer from a SCSI
disk drive connected to the host adapter.
Configuration
Option Value when Booting from Host Adapter Value when Not Boot- ing from Host Adapter
Port I/O Address Lowest slot number of
330h, 230h,130h Nonconflicting
Arbitration Level 5 Nonconflicting
Interrupt Level Nonconflicting Nonconflicting
HostAdapter BIOS
Address Enable only one BIOS Disable all other BIOS’s
HostAdapter SCSI ID 7 (or asrequired) 7 (or asrequired)
SCSI Parity Checking Onif all devicessupport
parity;
Offif any device does
not support parity
On if all devices support
parity;
Off if any device does
notsupport parity
Synchronous Data
Transfer Initiated by
HostAdapter?
Yes Yes
Fairness On On
Synchronous Data
Transfer Negotiation On: Performed by host adapter
Off: Performed by
peripheral
On

4
AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Adaptec Customer Support Services
■For information on software upgrades, new releases, technical
advice, and other topics, call Adaptec’s Electronic Bulletin
Board Service (BBS) 24 hours a day at 408-945-7727;
1200/2400/9600/14400 baud, 8 data bits, 1 stop bit, no parity.
■For the latest online information about Adaptec products and
services, call the Interactive Fax Service 23 hours a day, 7 days a
week, at 408-957-7150.
■For technical assistance, call Adaptec’s Technical Support Hot
Line at 800-959-SCSI (7274), or 408-945-2550. M–Th: 6:00 a.m.–
5:00 p.m., F: 6:00 a.m.–3:00 p.m., Pacific Time.
■To order Adaptec software and SCSI cables, call 800-442-SCSI
(7274), M–F: 6:00 a.m. to 5:00 p.m., Pacific Time. If you are call-
ing from outside the U.S. and Canada, the number is
408-957-7274.
■To request additional documentation for Adaptec products,
call 800-934-2766, M–F: 5:00 a.m. to 6:00 p.m., Pacific Time.
3

5
AHA-1640 Installation Guide
Part Number: 510160-00, Rev. B
Print Spec Number: 492772-00
Current Date: 5/20/94 ECN Date: 5/31/94
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These lim-
its are designed to provide reasonable protection against harmful interfer-
ence in residential installations. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause interference to radio or television equipment
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Move the equipment away from the receiver
• Plug the equipment into an outlet on a circuit different from that to
which the receiver is powered
• If necessary, the user should consult the dealer or an experienced radio/
television technician for additional suggestions
CAUTION: Only equipment certified to comply with Class B (computer
input/output devices, terminals, printers, etc.) should be attached to this
equipment, and must have shielded interface cables.
Finally, any change or modifications to the equipment by the user not
expressly approved by the grantee or manufacturer could void the user's
authority to operate such equipment.
Each host adapter is equipped with an FCC compliance label which shows
only the FCC Identification number. The full text of the associated label
follows:
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any inter-
ference received, including interference that may cause undesired
operation.
Adaptec, Inc.
691 South Milpitas Blvd.
Milpitas, CA 95035
Copyright © 1991, 1994 Adaptec, Inc. All rights reserved. Adaptec
and the Adaptec logo are registered trademarks and AHA is a
trademark of Adaptec, Inc. Micro Channel is a registered trade-
mark of International Business Machines Corporation.
Printed in Singapore
Stock No.: 510160-00, Rev. B KL 05/94
Information subject to change without notice.