ADDER ADDERLink INFINITY 3000 User manual

Welcome
This quick start guide covers some of the key points of the
ADDERLink™ INFINITY 3000 (ALIF3000) unit, which has
been created to address the growing requirement to connect
users to both physical and virtual machines. Using standard
VDI (Virtual Desktop Infrastructure) protocols - which are
built-in; the ALIF3000 delivers seamless access to legacy KVM
systems as well asVirtual Machine (VM) sources, from the
same common console.
Dual DisplayPort®video outlets provide support for a
single 2560x1600 display or two at a maximum 1920x1200
resolution (60Hz refresh).
Gigabit connections
The ALIF3000 receiver has two SFP ports located on its rear
panel, which can accommodate a range of ber or copper
networking modules, as suits your installation. Each port
can be connected to a separate gigabit ber (or copper)
network to permit access to a wider range of systems.A
third network port (RJ45) is also provided to allow separate
access, where necessary, to a corporate network to gain the
VM hosting conguration data. All three connections are
securely isolated within the ALIF3000 to prevent any cross
contamination between networks.
Important
ALIF3000 can ONLY be connected as part of an ADDERLink INFINITY system that is administered by
an ADDERLink INFINITY Manager. See rear page for Initial conguration details.
It is important that each ALIF3000 is set to its factory default settings, otherwise it will not be
discovered by the AIM server. If the standard settings have been changed in a previous installation, you
merely need to perform a manual factory reset on each unit. Please see the center pages.
ADDERLink™INFINITY 3000
Quick Start
© 2020 Adder Technology Limited • All trademarks are acknowledged.
Part No. MAN-QS-ALIF3000-ADDER_V1.0
www.adder.com
Initial conguration
ALIF3000 units depend upon ADDERLink INFINITY Manager (AIM) for almost all of their
conguration. As a new ALIF3000 unit is added to a network it must be in its factory default mode so
that AIM can engage with it and begin managing its resources. If an ALIF3000 is not in factory default
mode, please see the center pages.
To connect and configure an ALIF3000
1 Connect the ALIF3000 to an AIM-controlled network using either of the SFP ports via a suitable
CATx or ber SFP module.
2 Connect the necessary peripheral devices to the ALIF3000 and apply power to it via the supplied
power adapter.
3 The OLED screen on the front panel will provide status information:
ALIF3000
ALIF TX
Network
switch
Virtual
machines
Legacy KVM
system(s)
Full user details and setup
instructions can be found
at www.adder.com/en/
kvm-solutions/adderlink-
innity-3000
Please read the supplied safety
instruction leaet before use.
Minimum versions
In a mixed ALIF installation, ensure that the various
components have the following software versions:
• AIM server: v4.11
• ALIF100T-DVI: v4.07
• ALIF100T- VGA: v4.08
• ALIF1xxx: v4.9
• ALIF2xxx: v4.9
• ALIF3xxx: v1.0
• ALIF4xxx: v3.0
ALIF 3000
Searching...
––––––––––––––– ALIF 3000
Connecting...
––––––––––––––– ALIF 3000
Connected
–––––––––––––––
You should see the message progress from Searching... to Connected.
4 Log into AIM as an administrator and locate the new ALIF3000R entry within the Receivers section.
5 Click the icon on the ALIF3000R entry to congure the device. Please see the AIM user guide for
further details.
Full user details and setup instructions can be found at:
www.adder.com/en/kvm-solutions/adderlink-innity-3000

13 2
35
46
12
12VDC
Power
in
USB
Primary
display
Primary fiber or copper link (using 1GbE SFP modules) - KVM and VM links
Secondary fiber or copper link (using 1GbE SFP modules) - KVM and VM links
CATx copper link - VM-only link
Primary
SFP port
Secondary
display
Secondary
SFP port
RJ45
network
port
AdderLink
3000
1
2
Reset
switch
Head
phones
Line
out
USB
Mic
Gigabit
Ethernet
Gigabit
Ethernet
www.adder.com
MANAGEMENT SERVER
AIM Server
Status indicator
To perform a manual factory reset
A factory reset returns ALIF3000 unit to its default
conguration.
1 Power on the ALIF3000 unit.
2 Press-and-hold the button located next to the front
panel OLED screen for 10 seconds until the indicator
turns blue and the OLED screen shows the message:
In factory reset mode
3 You can now either:
• Continue with the factory reset: Use a long narrow
implement (e.g. a straightened-out paper clip) to
press-and-release the recessed reset button on the
front panel.
• Return to normal operation without resetting:
Press the button next to the OLED screen again.
4 Once the factory reset has been carried out the unit
should now be ready for discovery by an AIM server.
Connections
ALIF 3000
Searching...
–––––––––––––––
• Off No power.
• Green All services present as
compared to the conguration
required.
• Amber Running but video, USB or
network link missing (or not
connected to a transmitter/VM).
• Red Booting before processor
loaded or failed.
• Blue Factory reset mode active.
• Red/green ash Booting into factory recovery
mode.
• Green/blue ash Upgrade mode active.
• Fast green ash Identify mode active.
Status
indicator
AdderLink