ADEMCO hwb-416 User manual

INSTALLATION
INSTRUCTIONS
HWB-416
K1095-1 08/03
Description:
A multiplexing 16 zone expansion board for apex control panels.
Specifications:
16 dry contact inputs
Contacts wired normally open or closed
Optional 4.7K nd of Line resistors
10 second polling - trouble indication upon loss of communication
Power:
Current draw - 85mA
Source - 4 wire bus
Operating voltage - 9.5 to 14VDC
Wiring:
Observing proper color code, attach the HWB-416 to the 4 wire bus using four-wire stranded cable.
For wire runs up to 50 feet, 24 gauge wire is recommended and for runs over 50 feet use 22 gauge.
An HWB-416 can be wired directly to the control panel or daisy chained to any other 4 wire bus
peripheral in the system.
ach zone can be wired in one of three methods:
- With a 4.7K end of line resistor
- Fully Supervised with two 4.7K resistors (Selected in programming)
- Without an end of line resistor
See Wiring an Input in the Installation Manual for wiring an input with 1, 2 or no resistors.
Dip Switches:
An HWB-416 is two 8 input zone expanders on one circuit board. ach group of eight
(inputs L1-L8 and U1-U8) have separate dip switch settings. Depending on control panel support, up
to 8 groups with 8 inputs per section can be used per system (total of 64 expansion zones on 4
boards). To determine the number of zones supported by the panel being used consult the control
panels Installation Manual. Use the chart below to determine proper dip switch settings. xamples
of the most common dip switch settings are shown on the following page.
Diagram 1: HWB-416 Dip Switch Settings
/RZHU*URXS 8SSHU*URXS (QDEOH
*URXS
(2/1R
(2/
*URXS 2Q 2Q 2Q 2Q 2Q 2Q
*URXS 2II 2Q 2Q 2II 2Q 2Q
*URXS 2Q 2II 2Q 2Q 2II 2Q
*URXS 2II 2II 2Q 2II 2II 2Q
*URXS 2Q 2Q 2II 2Q 2Q 2II
*URXS 2II 2Q 2II 2II 2Q 2II
*URXS 2Q 2II 2II 2Q 2II 2II
*URXS 2II 2II 2II 2II 2II 2II
(QDEOH/RZ*URXS 2Q
(QDEOH+LJK*URXS 2Q
1R( 2 /5HVLVWRU
/RZ*URXS
2Q
1R( 2 /5HVLVWRU
+LJK*URXS
2Q
4
35678910
2
1

Programming:
Destiny 6100:
Consult Installation Manual for programming information.
Advantage and Destiny:
Program the number of zones used in each group into the appropriate memory location:
Group 1 : 214 Group 3 : 216 Group 5 : 218 Group 7 : 220
Group 2 : 215 Group 4 : 217 Group 6 : 219 Group 8 : 221
xample: To use all 16 inputs (Groups 1 & 2) on the first HWB-416, program 214,008 and 215,008.
L D- 1:
The green power L D on the HWB-416 indicates power and activity of the four-wire bus. When the
HWB-416 is operating correctly the L D should have a consistent flash that is often interrupted by
flashing at twice the normal rate. This indicates signaling on the four wire bus. ach time a zone is
opened, the L D should flash quickly for a brief moment. If the L D flashes at a constant rate and
no devices in the system are operating, check all four-wire bus connections. If the problem persists,
contact technical support at 800-272-7937.
Diagram 2: HWB-416 at default: Lower Group (#1), Upper Group (#2),
Upper and Lower Groups nabled, 1 .O.L. resistor on all
upper and lower group inputs.
Diagram 3: Most Common Dip Switch Settings:
Upper and Lower Groups nabled,
1 .O.L. resistor on all upper and
lower group inputs.
 
ON 8
76
543
2
1109
   -
8
76
543
2
1109
   -
8
76
543
2
1109
   -
8
76
543
2
1109
   -
8
76
543
2
1109
ON
ON
ON
ON
Board #1
Lower Group #1 - Upper Group #2
Board #2
Lower Group #3 - Upper Group #4
Board #3
Lower Group #5 - Upper Group #6
Lower Group (1, 3, 5, 7) Upper Group (2, 4, 6, 8)
Board #4
Lower Group #7 - Upper Group #8
L1 L2 L3 C L4 L5 C L6 L7 C L8 L9 C L10 L11 C L12 L13 C L14 L15 C L16C