Adeunis RF ARF09 User manual

A
RF09 AM
Transmitters & Receivers
User Guide

No part of this document may be reproduced or transmitted (in electronic or
paper version, photocopy) without Adeunis RF consent.
This document is subject to change without notice.
All trademarks mentioned in this guide are the property of their respective
owner.
ADEUNIS RF
283, rue Louis Néel
38920 Crolles
France
Phone [phone]
Fax [phone]
Ref. 06-02-V4-p

ARF09 User Guide
Ref. 06-02-V4-pft p 1
Table of contents
About this Document ........................................................................2
Declaration of conformity .................................................................3
ARF09 AM Transmitter......................................................................4
Dimensions / Pin assignment ................................................................4
ARF09 AM Receiver...........................................................................5
General use .........................................................................................5
Dimensions / Pin assignment ................................................................5
Specifications....................................................................................7
Standard compliance ........................................................................8

ARF09 User Guide
Ref. 06-02-V4-pft p 2
About this Document
This guide describes the ARF09 AM devices, their options and accessories.
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 3
Declaration of conformity
Manufacturer’s name: ADEUNIS R.F.
Manufacturer’s address Parc Technologique PRE ROUX IV
283 rue Louis NEEL
38920 CROLLES - FRANCE
declares that the product if used and installed according to the user guide available on
our web site www.adeunis-rf.com
Product Name: ARF09
Product Number(s): ARF6366A / ARF6374A / ARF6374I
is designed to comply with the RTTE Directive 99/5/EC:
EMC: according to the harmonized standard EN 301 489.
Safety: according to the standard EN 60950-1/2001
Radio: according to harmonized standard EN 300-220 covering essential
radio requirements of the RTTE directive.
Notes: - Conformity has been evaluated according to the procedure
described in Annex III of the RTTE directive.
- Receiver class (if applicable): 3.
According to the 1999/519/EC recommendation, minimum distance between the product
and the body could be required depending on the module integration.
Warnings: - CE marking applies only to End Products: Because this equipment is only a
subassembly, conformity testing has been reduced (equipment has been design in
accordance to standards but full testing is impossible). Manufacturer of End Products,
based on such a solution, has to insure full conformity to be able to CE label marking.
- As the integration of a radio module requires wireless
technological knowledge, ADEUNIS RF proposes its technical proficiency to its customers
for a pre-compliance qualification of end products. In case of no-conformity, ADEUNIS
RF will not be held back responsible if this stage has not been realised.
Crolles, November 6th, 2007
VINCENT Hervé / Quality manager
Download of the user guide
Thank you for having chosen the ADEUNIS RF products.
User guides can be uploaded directly on our web site www.adeunis-rf.com
Index Products
Paragraph OEM Modules > Transmitters & Receivers
Print version available upon request
9Tel : [phone]
9Email : [email protected]m
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 4
ARF09 AM Transmitter
General use
The TX A
RF09 AM
transmitter is a SAW transmitter developing a power of
10 mW on 50Ω. The use of half wave or quarter wave antennas is important
to get a high radiated power.
These transmitters are compatible with any ASK receiver able to
handle 100% modulations.
Dimensions / Pin assignment
Pins with 1/10" inch pitch
1 - TXData 4 - GND 6 - GND RF
2 - GND 5 - VCC 7 - ANTENNA Output
3 - N.C.
NOTE
•Transmitter is off when TXData = 0. The TXData input is directly the
command of the RF transistor bases. It is therefore important that it be
as close as possible to the Vdc (Minimum : Vdc – 0.5V)
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 5
•Data to be transmitted are injected on TXData pin. Because ARF08 is a
“rough” link, data rate has to be in the equivalent 500 / 2500 Hz range.
•For more informations about Radio Protocol : http://www.adeunis-
rf.com/list_faq.php?lng=FR or http://www.adeunis-
rf.com/list_faq.php?lng=EN
•A transmitter by definition generates a large electrical field. Avoid high-
impedance circuits close to the antenna , they will have to be moved
away or protected.
ARF09 AM Receiver
General use
The RX A
RF09 AM
receiver is a superheterodyne receiver with a sensitivity better
than 0.7µV. The use of a whip antenna is compulsory to obtain suitable
characteristics on receipt.
This receiver is compatible with any 100% ASK transmitter using a quartz or
SAW frequency reference.
Dimensions / Pin assignment
Pins with 1/10" inch pitch
1 - VCC 4 - VCC 6 - ANTENNA Input
2 - RXData 5 - GND 7 - GND RF
3 - Audio (For Test Only)
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 6
NOTE
•Receiver sampling is performed by direct switching of its VCC power
supply. For more information : http://www.adeunis-
rf.com/list_faq.php?lng=FR or http://www.adeunis-
rf.com/list_faq.php?lng=EN
•The AUDIO output cannot be used for analogue transmission; the
demodulator in fact provides the modulation logarithm !
•A receiver is by definition sensitive at very low electrical levels. It should
therefore be kept away from any known radioelectrical source (fast time
base, logic clock, PWM power supply, address / data bus...). Likewise
particular care should be taken over decoupling of its VDC (10 / 100 nF
RC circuit recommended) For more information : http://www.adeunis-
rf.com/list_faq.php?lng=FR or http://www.adeunis-
rf.com/list_faq.php?lng=EN
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 7
Specifications
A
RF09 AM
transmitter
Frequency 433.9 MHz / ARF6374A & I
(433.4 MHz / ARF6374B on request)
Developed power / ANT. Out. 10 mW / 50
Modulation ASK 100 %
Digital input / TXData 0 / VCC (Input Load 5 k)
NOTE
Transmitter is off (I < 100 nA) when TXData = 0.
Operating voltage / VCC 3 V ± 10% / ARF6374I
5 V ± 10% / ARF6374A & B
Consumption < 14 mA
Dimensions 46 x 18 x 3
Electrically & Pin compatible with Old ARF4006A & B & I Transmitters
A
RF09 AM
Receivers
Frequency 433.9 MHz / ARF6366A
(433.4 MHz / ARF6366B on request)
Sensitivity / ANT. In. 0.7µV (-110 dBm
for 10-2/PN9)
Demodulation ASK > 75 %
Bandwith 400 kHz
Digital Output / RXData 0 / VCC (10 kImpedance )
Settling Time < 10 ms
Operating voltage / VCC 4.5 to 6 V
Consumption 7 mA
Dimensions 40 x 20 x 3
NOTE
Electrically & Pin compatible with Old ARF4001A & B Receivers
TOP

ARF09 User Guide
Ref. 06-02-V4-pft p 8
Complete set
Binary throughput 1.2 to 2.4 kbps Manchester coding
Operating Temperature - 20 to + 70 °C
Regulating standards Radio : RTTE Direct. (EN 300 220-3)
EMC : EN 301 489 -1 & -3
Standard compliance
When using transmitters end receivers sub assemblies, the standard
compliance relates to the finished equipment.
In Europe, equipments has to comply to the RTTE directive. For this kind of
Low Power applications, the RTTE directive compliance will be established
with the respect of :
- EN300-220 radio standard .
- EN301-489 ECM standard .
- EN60950 Electric security (when usable).
IMPORTANT
if A
RF09 AM
daughter boards comply with the limits of the EN300-220
radio standard, their integration inside a mother board may change
some radioelectrical characteristics. (Harmonic levels, R.F
leackage...)
The final equipment, before the laboratory testing, has to be
examined in ADEUNIS RF lab to verify the compliance. After official
testing, equipment and test reports had to be archived to justify the
compliance.
TOP