Adirondack Technology EBO-N37TW-AIN User manual

I
NSTRUCTION
M
ANUAL
Ver 1.
0
High
Speed Dome Camera

Speed Dome Camera
Instruction
M
anual
2
/
57
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flas
h with arrowhead symbol is intended to alert the user to
the presence of un
-
insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons
.
This exclamation point sym
bol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance
.
This Device compiles with Part 15 of the FCC Rules. Operation is subject to
the following
two conditions:
(1) This device may not cause harmful interface, and
(2) This device
must accept any interference received, including
interference that may cause undesired operations.

Speed Dome Camera
Instruction
M
anual
3
/
57
Important Safety Guide
1.
Read
, heed and follow
all the
In
structions
Read all
the safety and operating instructions before using the
product
.
2.
Keep this
manual
Keep
th
is manual
for
reference
in future
.
3.
Attachments
/ Accessories
Use only
the
attachments
or accessories
specified by the manufacturer.
4.
Installation

Do not install near any heat resources such as radiators, heat registers, stoves, or other
appratus including amplifiers that product heat. Improperly installed
product may fall,
caus
e
serious injury to a child or adult
and damage the product
.

Do not
block
any ventilation holes or openings. Install in accordance with the
manufacturer
’
s instructions
.

Use only
with the cart, stand, tripod, bracket, mounting devices, or table specified by
the manufacturer
.

Installation should be done only by qualified personne
l and conform to all the
instructions by the manufacturer
.

Refer all servicing to qualified service personnel
.

Unless the produc
t is specifically marked as IP67
, more than IP6
7
or confirmed by the
manufacturer, it is designed for indoor use only and it mus
t not be installed where
expo
sed to rain and moisture
.

Do not load on the product
.

Use stainless steel hardware to fasten the mount
.

To prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant properly around hole
s
.

These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the
operationg instructions unless you are qualified to do so
.

Use only replacement
parts specified by the manufacturer
.
5.
Power source
This product should be operated only from the type of
the
power source indicated on the
marking label
.
NOTICE

Speed Dome Camera
Instruction
M
anual
4
/
57
Caution

Operating

Before using,
make sure
that the
p
ower supply and
others are properly
ins
talled
.

While operating, if any abnormal condition or malfunction is observed, stop using the
product
immediately and then c
ontact
your local dealer
.

Handling

Do not disassemble
or tamper with
the
parts
inside the
product
.

Do not drop
or subject
the
produc
t
to shock and vibration
as this can
damage
the
product
.

Care must be taken when you clean the clear dome cover
.
Especially,
scratch and dust
will ruin the
quality of
the product
.

Installation and Storage

Do not install the
product
in areas of extreme
temp
erature
, which
exceed the allowable
range
.

Avoid installing in humid or dusty places
.

Avoid installing in places where radiation
is present
.

Avoid installing in places where there are strong magnetic fields and electric signals
.

Avoid installing in places
where the
product
would be subject to strong vibrations
.
NOTICE

Speed Dome Camera
Instruction
M
anual
5
/
57
②
Introduction
Model Code
6
Feature
s
8
Package Components
1
1
Main Part Description
1
3
②
Installation
DIP Switch Setup
1
4
Installation with Ceiling Mount Bracket
1
7
Installation with Wall Mount Bracket
1
8
Wiring
and
Cabling
1
9
②
Operation
Check Point before Operation
2
2
Check Points for Preset and Pattern Function before Operation
2
2
OSD
Menu
2
3
Reserved Preset (Hot Keys)
2
3
Preset
2
4
Swing
2
4
Pattern
2
5
Group
2
6
Other Fun
ctions
2
6
OSD Display
2
8
②
OSD Menu
Quick Programming Guide
2
9
Main Menu
2
9
Display
Setup
30
Privacy Zone Mask Setup
31
Camera Setup
3
3
Motion Setup
3
8
Preset Setup
41
Swing Setup
4
3
Pattern Setup
4
4
Group Setup
4
5
S
ystem Initialize
4
8
②
Specifications
4
9
Dimension
5
6
TABLE OF CONTENTS

Speed Dome Camera
Instruction
M
anual
6
/
57
Model Code
E B O - N 3 7 T W - A I N
Series
EBO
: with Fan/Heater
EBI
: without Fan/Heater
Video Signal
N
: NTSC
P
: PAL
Zoom
27T
: Optical x27
33T
: Optical x33
33W
: Optical x33, WDR
37T
: Optical x37, WDR
Rated Power
D
: DC12V
A
: AC24V
U
: Dual (AC24V/DC12V) : EBI model only
Sensor I/O
I
: 3 In / 1 Out
X
: without I/O
Network
N
: H.264 IP Function
X
: without IP
Mount Bracket
W
: Wall Mount
C
: Ceiling Mount
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
7
/
57
M B O - N 1 0 T W - D I N
Series
MBO
: Mini Aluminum Outdoor (with Fan/Heater)
MBI
: Mini Aluminum Indoor (without Fan/Heater)
Video Signal
N
: NTSC
P
: PAL
Zoom
10T
: x10 / Samsung Techwin
Rated Power
D
: DC12V
A
: AC24V
U
: Dual (AC24V/DC12V) : MBI model only
Sensor I/O
I
: 3 In / 1 Out
X
: without I/O
Network
N
: H.264 IP Function
X
: without IP
Mount Bracket
W
: Wall Mount
C
: Ceiling Mount
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
8
/
57
Feature
s

Powerful
Zoom
Camera & Setup Options

Image Sensor
:
1/4"
Double density i
nterline
t
ransfer
CCD
(37T, 33W model)
1/4"
Super HAD color CCD
(
27T, 33T model
)
1/4" Interline Transfer CCD
(10T model)

Zo
om
:

2
7
Optical Zoom
,

1
2
Digital Zoom
(
2
7T
model
)

3
3
Optical Zoom,

1
2
Digital Zoom (
3
3T, 33W
model
)

37
Optical Zoom,

1
2
Digital Zoom (
37T model
)

10
Optical Zoom,

1
0
Digital Zoom (
10T model
)

Day & Night
, Pri
vacy Mask and
WDR
(WDR
:
37T, 33W
m
odel
s
o
nly)

SNR (Super Noise R
e
duction) Function

Various Focus Mode :
Auto
-
Focus, Manual Focus
,
Semi
-
Auto Focus

Various S
e
tup Options in OSD
Menu
.

Powerful Pan/Tilt Functions

MAX. 360

/sec H
igh Speed Pan/Tilt Motion

With
the
Vector Drive Technology, Pan/Til
t motions are accomplished along the
shortest
path. As a
result, the time to target view is
remarkably
short
and the video on
the
monitor is very natural in
monitor
ing
.

With the
Micro
-
Stepping Control Technology
,
the video
looks
very natural at high
zoom m
agnification
during a
jog operation on
a
controller
since
the
camera
can be
controlled by
0.05

/sec
.
Hence it is very easy to make
the
camera
focus on
desired
target view
s
at high zoom magnification
.
Additionally
it is easy to make
the
camera
focus on
desi
red position
s
with zoom
-
proportional pan/tilt movement.

Preset, Pattern, Swing, Group, Privacy Mask and More
…

M
AX
. 12
7 Pre
sets
are
programmable
and
each
preset can
have
its own
parameter
values
independent
ly
from the other presets
.
For
an
example,
refer
to the below table.
PresetN
o.
WhiteBalance
AutoExposure
•••
Label
Remarks
Preset1
C
ase
A
Case
3
“
E
NTRANCE
”
Preset2
C
ase
C
Case
5
“
WAREHOUSE
”
•••
Preset95




Reservedfor
OSD
Menu
•••
Preset128
C
ase
K
Case
9
“
TERRACE
”
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
9
/
57

MAX. 8 sets of Swing are
programma
ble.
This function is that
the
camera
moves
repetitively
between two preset positions
at programmed
speed
s
.

MAX. 4 Patterns are
programmable
. This
function is that
the
camera
memorizes the
path (mostly curve path) by the
joystick of the controller and revives the
trajectory
operated by
the
joystick as closely as possible.

MAX
. 8 sets of Group
are
programmable
.
This
function
is that the camera
memorizes
the combination of
Preset
s, Pattern and/or Swings
sequently
and runs
Pr
eset
s, Pattern
and/or Swings
repetitively
.
A Group can be combined upto 20 functions with any of
Preset/Pattern/Swing.

MAX.
8
or 4
Privacy
M
asks
are
programmable
, not to intrude on any other
’
s
priva
cy
.
(10T model : 4 Privacy Masks)

PTZ(Pan/Tilt/Zoom) Co
ntrol

With the RS
-
485
communication
connection
,
MAX
. 255
units
of cameras can be
connected to a single controller.

Pelco
-
D or Pelco
-
P protocols can be selected as a control pr
otocol in the current
firmware
version
.

OSD(On Screen Display) Menu

OSD menu i
s provided to display the status of camera and to configure the functions
interactively.

The information such as Camera ID, Pan/Tilt
A
ngle,
Direction,
Alarm I
nput
and Preset
is
displayed on screen
.

Alarm I
n
/O
ut Function
(
Only for the
m
odels which
have
I/
O
function
)

3
alarm sensor inputs and 1 alarm sensor outputs are available.

Alarm sensor input is decoupled with photo
-
coupler
s
to avoid external electric noise
and shock perfectly.

Both of N
.
O
.
(Normal Open) sensors and N
.
C
.
(Normal Close) sensors can be us
ed and
the signal range of
the
sensor input is from DC 5.0V to 12.0V for various applications.

The
camera
can be
set to move to a Preset
position or
to run functions
such as Pattern,
Swing
and Group when there are
external
sensor activations.
Also
“
Post Al
arm
”
function
is possible
, which i
s supposed to activate after user
-
defined time period and
sequentially
in succession to the action by external sensor activation
s
.

Reserved Presets
(
Hot Keys
)

Most camera
setup options
can be set up easily and directly w
ith
the
reserved preset
s
(Hot Keys)
,
without
entering into OSD menu. For more information, refer to
“
Reserved
Preset
s
(Hot Keys)
”
in this manual.
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
10
/
57

Network
Function
(
Only for the IP addressable models)

Network functions including r
emote monitoring
,
bidire
ctional audio
and others
are
available
through IP based network such as
LAN, ADSL/VDSL, and Wireless LAN
. For
more information, refer to the separated manual for IP Addressable models.

Perfect Outdoor Environment Compatibility and Easy Installation

The
f
ans and heaters are built
-
in in
the
camera for cold and hot temperature
environment. Also idealistic mechanical design protects
the
camera from water and
dust. (
IP6
7
when installed properly
with wall mount bracket only
/
Only for outdoor
models)

It is eas
y to install and repair
the
camera.
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
11
/
57
Package Component
(E
BO/
E
BI model)

Product & Accessories

Main Body&SurfaceMount Bracket

DefaultAccessories
[
Main Cable,Wrench
]

Accessories forThe Models with Alarm In/Out
Function
[I/O
Cable]

Accessories forThe IP Addressable Models
[
Crossover
LANCable,AudioCable,CD]

Brackets (Optional)

Wall Mount Bracket
[
Screws :Machine M5

15,Hex Lag #14

50
]

CeilingMount Bracket
[
Screws :Machine M5

15,Anchor Bolt3/8"

70
]
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
12
/
57
Package Component (MBO/MBI model)

Product & Accessories

Main Body&SurfaceMount Bracket

DefaultAccessories
[Main Cable,Wrench]

Accessories forThe Models with Alarm In/Out
Function[I/O Cable]

Accessories forThe IP Add
ressable Models
[CrossoverLANCable,Audio Cable,CD]

Brackets (Optional)

Wall Mount Bracket
[Screws :Machine M5

15,Hex Lag #14

50]

CeilingMount Bracket
[Screws :Machine M5

15,Anchor Bolt3/8"

70]
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
13
/
57
Main Part Description
DIP Switch
Reset Switch (IP Model)
LAN Port (IP Model)
Audio Port (IP Model)
Main Connector
Sensor I/O Port (I/O Model)
Dome Cover
Mounting Screw Hole
Drop Prevention Spring

Dome Cover
Do not detach the protection vinyl from the dome cover before
finishing all the installation process to protect the dome cover from
scratch
es or dust.

DIP Switch
Used to set up camera IDs and protocols.

Drop Prevention
Spring
This part
keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to
the drop prevention hook of main body as shown in picture for
further tasks
.

MountingScrew
Hole
Used to assemble the main body wit
h a bracket with screws.

Main Connector
Used for the power wire, the video cable and the RS
-
485
communication cable connection.

SensorI/OPort
Used for the sensor in/out connection. (The sensor I/O function
possible models only)

LANPort
Used for
the Ethernet connection. (IP addressable models only)

AudioPort
Used for the audio in/out connection. (IP addressable models only)

Reset Switch
Used to initialize all the network configurations to the factory
default. (IP addressable models only)
Press the button for more
than 5 seconds to initialize the network system.
I
NTRODUCTION
1

Speed Dome Camera
Instruction
M
anual
14
/
57
DIP
Switch Setup
Before installing the camera, set
up the DIP switch to configure
the
camera ID and
the
communication
protocol.

Camera ID Setup
ON
ON
1
2
3
4
5
6
7
8

ID numbers of cameras are set up with binary numbers.
See the examples shown below.
Pin
1
2
3
4
5
6
7
8
BinaryValue
1
2
4
8
16
32
64
128
ex) ID=5
on
off
on
off
off
off
off
off
ex) ID=10
off
on
off
on
off
off
off
off

The camera ID range is
“1~
255
”
.
Camera ID must not be
“
0
”
!

The factory default of the camera ID is
“
1
”
.

Match the camera ID with the Cam ID setting of your DVR
or Controller to control the camera.

If you are connecting a single camera to
a controller,
terminate the camera. When connecting more than one
camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera
farthest in cable length from the controller.

Note that the total length
of the communication cable
between a controller and the camera(s) on the same
communication line must be less than 1.2Km.
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
15
/
57

Communication Protocol Setup
1
2
3
4
ON
ON

Sele
ct an
appropriate
Protocol with the DIP switch combination.
Switch Mode
Protocol
P0
(Pin 1)
P1
(Pin 2)
P2
(Pin 3)
OFF
OFF
OFF
PELCO
-
D, 2400 bps
ON
OFF
OFF
PELCO
-
D, 9600 bps
OFF
ON
OFF
PELCO
-
P, 4800 bps
ON
ON
OFF
PELCO
-
P, 9600 bps
Others
Reserved

Match the camera protocol with the camera protocol in the setting of
your DVR or controller to control the camera.

Adjust the DIP switch after turning off the camera. If you changed the
camera protocol by changing the DIP S/W, the change will be effective
after you reboot the camera.

The factory default protocol is
“
Pelco
-
D, 2400 bps
”
.
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
16
/
57

Terminal Resistor Setup
1
2
3
4
ON
ON
The terminal resistor is used for the following cases.

Case 1 : In case that the control cable length between a camera and
a controller is relatively very long (1:1 Connection)
If the
communication
cable length i
s very long, the electrical signal will
bound in the
terminal
point. This reflected signal causes distortion of
original signal. Accordingly, the camera can be out of control. In this
case, the
terminal
resistor of both sides i.e. the camera and the
contro
ller must be set to
‘
ON
’
state.

Case 2 : In case that m
ultiple
cameras are connected to a
controller.
Due to similar reasons with the case 1, the
terminal
resister of the
controller and the last camera must be set to
‘
ON
’
state. The last camera
means the
camera farthest in cable length from the controller. Do not
turn on the terminal resistor of all the
cameras
on the same
communication
cable.
Contr
oller
#1
#2
#n
T
erminal Resistor ON
RS-485
T
erminal Resistor
OFF
T
erminal Resistor
OFF
T
erminal Resistor
ON
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
17
/
57
Installation with Ceiling Mount Bracket
①
Remove the ceiling tile from the ceiling
and cut a hole whose diameter is
30~40mm on the ceiling tile
to pass the
wire(s) and cable(s) through to the upside
of the ceiling. (In case of the wiring and
cabling through the mounting surface
only) Then prepare the ceiling mount
bracket. Pull the wire(s) for the system as
below.
(
Anchor Bolt 3/8"

70
)
②
Hook up
“
Drop Prevention Spring
”
on
main body to prevent camera from
unexpected drop
and p
ull the wire(s) and
cable(s) for the system as below.
③
L
ine up the mold lines and assemble
main body to
mount adaptor
and turn it.
And
a
ssemble the main both with the
camera mount adaptor with the 3 screws
.
(Machine M5

15)
.
④
Screw the dome cover to the main body
and remove the protection vinyl from the
dome cover
.
ImportantNotice

Beforestarting
the
installation,makesurethat
the
Camera IDandProtocol areset
upproperly.

To adjust the installation height from the mounting surface, the pipe and coupler should be needed
between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling
mount bracket.Notethat theyare
not
suppl
ied bythemanufacturer.
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
18
/
57
Installation with Wall Mount Bracket
①
Make a hole whose diameter is 30~40mm
on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface. (In case of the wiring and cabling
through the mounting
surface only) Then
prepare the wall mount bracket. Pull the
wire(s) and cable(s) for the system as
below. Attach the wall mount bracket to
the mounting surface
. (
Hex Lag #14

50
)
②
Hook up
“
Drop Prevention Spring
”
on
main body to prevent camera from
unex
pected drop
and p
ull the wire(s) and
cable(s) for the system as below.
③
L
ine up the mold lines and assemble
main body to
mount adaptor
and turn it.
And a
ssemble the main both with the
camera mount adaptor with the 3 screws
.
(Machine M5

15).
④
Screw
the dome cover to the main body
and remove the protection vinyl from the
dome cover
.
ImportantNotice

Beforestarting theinstallation,makesure thattheCameraIDand Protocolare setupproperly.
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
19
/
57
Wiring and Cabling
RS-485
BNC
SENSOR I/O
LAN CABLE
AUDIO
CABLE
MAIN CABLE
I/O CABLE
BROWSER
POWER
MONITOR
CONTROLLER / DVR
MIC
SPEAKER
IR
SENSOR
DOOR
SWITCH
INTERNET

Port Description

Main Cable
Port Pin Number
(RJ45)
Connect
or / Wire Color
Signal
1
BNC
Connector
Video +
2,4
Video

5
Red
RS
-
485 +
3
Yellow
RS
-
485

7
Orange
Power +
6,8
White
Power


I/O Cable
Port Pin Number
(RJ25)
Wire Color
Signal
1
Blue
IN COM
+
2
Yellow
I
N 1

3
Green
IN 2

4
Red
IN 3

5
Black
OUT A
6
White
OUT B

Audio Cable
Port Pin Number
Connector / Wire Color
Signal
1
RCA (
Yellow
)
Audio IN
2
Audio GND
3
RCA (
White
)
Audio OUT
INSTALLATION
2

Speed Dome Camera
Instruction
M
anual
20
/
57

Power Description

Carefully check the voltage and current cap
acity of
the
rated power.
The r
ated power is
indicated in the back of main unit.
Model
InputVoltage
Range
Current
Consumption
DC12V
Model
Analog Model
E
(M)
B
I
-





-
D

X
DC11V ~ 18V
0.8A
E
(M)
B
O
-





-
D

X
2.5A
IP
Addressable
Model
E
(M)
B
I
-





-
D

N
1.3A
E
(M)
B
O
-





-
D

N
3.0A
AC24V Model
Analog Model
E
(M)
B
O
-





-
A

X
AC 17V~29V
1.5A
Dual
Power
Model
Analog Model
E
(M)
B
I
-





-
U

X
DC11V ~ 18V
or
AC 17V~29V
DC12V,0.8A
/
AC 24V,0.4A

For
the
DC
input
models,
be careful with
the
polarit
y of DC
power
.
The system should be
permanentally damaged by w
rong DC input
.

In case that the length of the power wire is very long, there may be voltage drop and the
syatem may not work properly. Make the length of the power wire as short as possible.

RS
-
485
Communication

F
or PTZ control, connect the cable(s) to your
keyboard or DVR. To connect multiple
cameras to a single controller, RS
-
485 communication should be connected in
parallel
as shown below.
If you are connecting a single camera to a control
ler, terminate the
camera. When connecting more than one camera to a single controller, terminate the
last camera on the communication line. The last camera means the camera farthest in
cable length from the controller.
Note that the total length of the co
mmunication cable
between a controller and the camera(s) on the same communication line must be less
than 1.2Km.
INSTALLATION
2
CONTROLLER / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-