ADJ ELEMENT ST HEX User manual

User Instructions
ELEMENT ST HEX
USA# ELE457
EU# 1226100379
UPC# 818651027853
ITF-14# 10818651027850

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-
ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
©2020 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-
tion of this product.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with
the included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
· Reorient or relocate the device.
· Increase the separation between the device and the receiver.
· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.
02/05/20 1 1.00 6/7/8/11/12 Initial Version
Date Document
Version
Software
Version > DMX Channel Mode Notes

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 2
Element ST Hex Table of Contents
Introduction
Features I Warranty Registration I Installation
Safety Guidelines
Battery Precautions
Battery Status & Charging
Overview
Installation
DMX Addressing
DMX Modes
Color Macro Chart
System Menu
WiFly Set Up I WiFly Master-Slave Set Up
UC IR & Airstream Control
Dimmer Curve Chart
Dimensional Drawings I Tilt Adjustment Angles
Trouble Shooting I Cleaning
Limited Warranty (USA Only)
Technical Specications
3
4
5
7
8
9
10
11
12
14
15
18
19
20
21
22
23
24

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 3
Element ST Hex Introduction
Unpacking: Thank you for purchasing the Element ST Hex by ADJ Products, LLC. Every Element ST
Hex has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your xture for any damage and be sure all accessories necessary to oper-
ate the unit has arrived intact. In the case damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Do not return this unit to your dealer
without rst contacting customer support.
Introduction: The Element ST Hex is a rechargeable lithium battery powered, DMX intelligent, LED
par fixture with ADJ’s WiFly TransCeiver with wireless DMX built-in. WiFly control and battery power
gives you the freedom to set up your unit where ever you wish without the restrictions of power or DMX
cabling. This unit can be used in a stand alone mode or connected in a Master/Slave set up. To optimize the
performance of this product, please read these operating instructions carefully to familiarize yourself
with the basic operations of this unit. These instructions contain important safety information regarding
the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit
forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit http://parts.americandj.com
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [email protected]
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]
www.adj.eu | [email protected]
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.

Element ST Hex Features
Element ST Hex Warranty Registration
The Element ST Hex carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,
you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-
tacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the
shipper.
ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 4
• Multiple Operating Modes
• Electronic Dimming 0-100%
• RGBWA+UV Color Mixing
• 5 Selectable Dimming Curves
• 63 Color Macros
• Built in Microphone
• Multiple DMX Channel Modes
• Battery Powered with Rechargeable Lithium Battery
• Built-In ADJ’s WiFly TransCeiver Wireless DMX
• ADJ UC IR & Airstream IR compatible
Incuded Accessories:
1 x 12.6V/2A DC Power Adapter
1 x UC IR Remote Control
1 x Airstream IR Transmitter

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 5
Element ST Hex Safety Guidelines
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s housing is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 22
for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. The appliance does not appear to operate normally or exhibits a marked change in performance.
C. The fixture has fallen and/or subjected to extreme handling.

Element ST Hex Safety Precautions
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.
AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH
OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE
DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE
DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.
ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 6

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 7
Element ST Hex Battery Precautions
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high current which could cause the battery
to overheat which may result in electrolyte gel leakage, harmful fumes, or explosion. The LIR tabs
may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build
up and damage of the battery. An appropriate circuitry with PCM is employed to protect accidental
short circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or shortend life of the LIR battery.
3. Other
3.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to the batteries. Direct soldering may
cause damage of components, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to provide extra safety protection.
The battery pack is constructed in a way that no short circuit will occur which may cause smoke or
re.
3.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery, which may lead to harmful fumes, re,
explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the electrolyte gel come into contact
with the skin or eyes, ush the area of contact immediately with fresh water and seek medical atten-
tion immediately.
3.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in re. This may cause an explosion, which would be
very dangerous.
3.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices,
coee or other.
3.6 Battery Replacement
For battery replacement please contact ADJ customer support [phone].
3.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by shock. Should the battery be found dam-
aged, including damages to the plastic casing of the battery, deformation of the battery package,
smelling of an electrolyte, or leakage of the electrolyte gel, or other, DO NOT use the battery. A bat-
tery with a odor of electrolyte or a gel leakage should be placed away from re to avoid re or explo-
sion.

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 8
Element ST Hex Battery Precautions
4. Battery Storage
When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We
recommend that during long periods of storage that the battery be charged every 6 months. Doing
this will prolong the life of the battery and will also make sure that the battery charge does not fall
below the 30% mark.
5. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if
stored for a long period of time without being used. In addition, if the various usage conditions such
as charge, discharge, ambient temperature, etc. are not maintained within the specied ranges, the
life expectancy of the battery maybe shortened or the device in which the battery is used may be
damaged by electrolyte gel leakage. If the batteries cannot maintain a charge for long periods of
time, even when they are charged correctly, this may indicate it is time to change the battery.
6. Battery Disposal
Please dispose of battery according to local regulations.
Battery Status:
This function is used to check the battery life status.
1. Plug the fixture in and press the BATTERY icon.
2.Press the UP or DOWN buttons to highlight CURRENT LIFE and press ENTER. The number that is
displayed is the remaining battery life.
Never let the battery fully die, this severly shortens the life of the battery.
Battery Charging:
This function is used to check the battery charging status.
1. Plug the fixture in and press the BATTERY icon.
2.Press the UP or DOWN buttons to highlight CHARGING TIME and press ENTER. The number that
is displayed is the remaining battery life.
To recharge the battery, plug the supplied power adapter into the input located on the bottom of the
unit and plug the other end into a matching power source. TO CHARGE THE BATTERY, THE POWER
SWITCH MUST BE IN THE “ON” POSITION. It takes about 5 hours to reach full charge.
NOTE: CHARGING TIME will display “------------” when:
- The power adapter is NOT connected.
- The POWER SWITCH is “ON” but the LOAD setting is set to “OFF”.
- The power adapter is connected but the POWER SWITCH is “OFF”.
Note: When unplugging the unit from charging and then applying power via battery, there will
be a minimal charge drop.
For faster charging, turn the POWER SWITCH “ON” and the LOAD setting to “OFF”.
Element ST Hex Battery Status & Charging

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 9
Element ST Hex Overview
1. Service Port: This port is used for software updates.
2. Tilt Adjustment Leg: This tilt adjustment leg is used to angle the unit to various degrees. There
are 7 dierent angled levels. See page 21 for more information.
NOTE: Sliding the adjustment leg out to far will cause the leg to “dislodge” from the unit.
3. Voltage Adapter Input: This input is used to connect the included voltage adapter. After connecting
the adapter, plug the other end into a matching power source.
NOTE: Please only use the provided power adapter that is included with the unit.
4. Power On/O Switch: This switch is used to power ON/OFF the unit.
1
3
2
4

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 10
Element ST Hex Installation
This unit is primarily designed for uplighting. The unit does come with a threaded mounting hole for
use with clamp installation. Screw one clamp via a M10 screw into the insert located on the rear of
the unit.
NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚C.
Do not place this lighting xture in an enviroment where the temperatures are under or above the
temperatures stated above. This will allow the xture to run at its best and help prolong the xture
life.
The Element ST Hex is fully operational in three dierent mounting positions; set on a at level surface
(ideal set up), hanging upside-down, or mounted sideways on trussing. Be sure this xture is kept at
least 12m (40ft) away from any ammable materials (decoration etc.). Always use and install a safety
cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.
Never use the carrying handle for a secondary attachment.
Clamp Mounting Hole
Attach a clamp to the unit by screwing
the clamp in clockwise.

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 11
All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.
You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures
simultaneously.
If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.
In the case of the Element ST Hex, when in 6 channel mode you should set the starting DMX address
of the rst unit to 1, the second unit to 7 (6 + 1), the third unit to 13 (7 + 6), and so on. (See chart below
for more details.)
Element ST Hex DMX Addressing
Channel Mode Unit1
Address
Unit2
Address
Unit3
Address
Unit4
Address
6 channels  1 7  1319 
7 channels  1 8  1522 
8 channels  1 9  1725 
11 channels 1 12 23 34
12 channels 1 13 25 37

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 12
Element ST Hex DMX Channel Modes
RED
0~100%
GREEN
0~100%
000-255
BLUE
0~100%
WHITE
0~100%
AMBER
0~100%
UV
0~100%
VALUES FUNCTIONS
STROBING
MASTER DIMMER
0~100%
LED OFF
LED ON
STROBING SLOW-FAST
LED ON
PULSE STROBING SLOW-FAST
LED ON
RANDOM STROBING SLOW-FAST
LED ON
PROGRAM SELECTION MODE
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
6 CH
7 CH 8 CH 11 CH 12 CH
7 7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
000-255
000-255
000-255
000-255
000-255
000-255
000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255
8 8
9 9
RGBWA+UV DIMMING MODE
COLOR MACRO MODE
COLOR CHANGE MODE
COLOR FADE MODE
SOUND ACTIVE MODE
000-051
052-102
103-153
154-204
205-255
ADJ ELEMENT ST HEX
DMX Channel Values & Functions
Supports Software Version >1.00
Feature subject to change without notice

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 13
Element ST Hex DMX Channel Modes
10
COLOR FADE MODE
COLOR FADE 1
COLOR FADE 2
COLOR FADE 3
COLOR FADE 4
COLOR FADE 5
COLOR FADE 6
COLOR FADE 7
COLOR FADE 8
COLOR FADE 9
COLOR FADE 10
COLOR FADE 11
COLOR FADE 12
COLOR FADE 13
COLOR FADE 14
COLOR FADE 15
COLOR FADE 16
SOUND ACTIVE MODE
SOUND ACTIVE MODE 1
SOUND ACTIVE MODE 2
SOUND ACTIVE MODE 3
SOUND ACTIVE MODE 4
SOUND ACTIVE MODE 5
SOUND ACTIVE MODE 6
SOUND ACTIVE MODE 7
SOUND ACTIVE MODE 8
SOUND ACTIVE MODE 9
SOUND ACTIVE MODE 10
SOUND ACTIVE MODE 11
SOUND ACTIVE MODE 12
SOUND ACTIVE MODE 13
SOUND ACTIVE MODE 14
SOUND ACTIVE MODE 15
SOUND ACTIVE MODE 16
000-015
016-031
032-047
048-063
064-079
080-095
096-111
112-127
128-143
144-159
160-175
176-191
192-207
208-223
224-239
240-255
000-015
016-031
032-047
048-063
064-079
080-095
096-111
112-127
128-143
144-159
160-175
176-191
192-207
208-223
224-239
240-255
10
PROGRAMS
COLOR MACRO MODE
PLEASE SEE THE COLOR MACRO CHART
ON PAGE 14
COLOR CHANGE MODE
COLOR CHANGE 1
COLOR CHANGE 2
COLOR CHANGE 3
COLOR CHANGE 4
COLOR CHANGE 5
COLOR CHANGE 6
COLOR CHANGE 7
COLOR CHANGE 8
COLOR CHANGE 9
COLOR CHANGE 10
COLOR CHANGE 11
COLOR CHANGE 12
COLOR CHANGE 13
COLOR CHANGE 14
COLOR CHANGE 15
COLOR CHANGE 16
000-255
000-015
016-031
032-047
048-063
064-079
080-095
096-111
112-127
128-143
144-159
160-175
176-191
192-207
208-223
224-239
240-255
VALUES FUNCTIONS6 CH 7 CH 8 CH 11 CH 12 CH

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 14
Element ST Hex DMX Channel Modes
NOTES:
When Channel 9 is between the values of 0-51, Channels 1-6 are used, and Channel 8 will control
strobing.
When Channel 9 is between the values of 52-102, Channel 10 is in Color Macros Mode, and
Channel 8 will control strobing.
When Channel 9 is between the values of 103-153, Channel 10 is in Color Change Mode, and
Channel 11 will control the color change speed.
When Channel 9 is between the values of 154-204, Channel 10 is in Color Fade Mode, and
Channel 11 will control the color fade speed.
When Channel 9 is between the values of 205-255, Channel 10 is in Sound Active Mode, and
Channel 11 will control the sound sensitivity.
PROGRAM SPEED/SOUND SENSITIVITY
PROGRAM SPEED SLOW-FAST
LEAST SENSITIVE-MOST SENSITIVE
000-255
000-255
1111
12
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT SETTING
000-020
021-040
041-060
061-080
081-100
101-255
VALUES FUNCTIONS6 CH 7 CH 8 CH 11 CH 12 CH
Element ST Hex Color Macro Chart
0-3=Off
64-67=B+W
128-131=G+B+W
192-195=R+B+W+A
4-7=Red
68-71=B+A
132-135=G+B+A
196-199=R+B+W+UV
8-11=Green
72-75=B+UV
136-139=G+B+UV
200-203=R+B+A+UV
12-15=Blue
76-79=W+A
140-143=G+W+A
204-207=R+W+A+UV
16-19=White
80-83=W+UV
144-147=G+W+UV
208-211=G+B+W+A
20-23=Amber
84-87=A+UV
148-151=G+A+UV
212-215=G+B+W+UV
24-27=UV
88-91=R+G+B
152-155=B+W+A
216-219=G+B+A+UV
28-31=R+G
92-95=R+G+W
156-159=B+W+UV
220-223=G+W+A+UV
32-35=R+B
96-99=R+G+A
160-163=B+A+UV
224-227=B+W+A+UV
36-39=R+W
100-103=R+G+UV
164-167=W+A+UV
228-231=R+G+B+W+A
40-43=R+A
104-107=R+B+W
168-171=R+G+B+W
232-235=R+G+B+W+UV
44-47=R+UV
108-111=R+B+A
172-175=R+G+B+A
236-239=R+G+B+A+UV
48-51=G+B
112-115=R+B+UV
176-179=R+G+B+UV
240-243=R+G+W+A+UV
52-55=G+W
116-119=R+W+A
180-183=R+G+W+A
244-247=R+B+W+A=UV
56-59=G+A
120-123=R+W+UV
184-187=R+G+W+UV
248-251=G+B+W+A+UV
60-63=G+UV
124-127=R+A+UV
188-191=R+G+A+UV
252-255=R+G+B+W+A+UV

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 15
Element ST Hex System Menu
SYSTEM MENU
This xture includes a system menu with an easy to navigate touch screen control panel where all
necessary settings and adjustments are made. When rst powering on the xture, the xture’s main
menu will be displayed. On the main menu, press the menu you would like to access. In the next
menu screen, you can navigate through the dierent sub-menus with the UP and DOWN buttons.
When you reach a sub-menu that you would like to enter press the ENTER button. When you reach
a sub-menu or eld that requires adjusting, press the ENTER button to access that eld and use the
UP or DOWN buttons to adjust the eld. Pressing the ENTER button once more to conrm your setting.
You may exit the main menu at any time without making any adjustments by pressing the BACK/EXIT
button.
DMX
SETTINGS
PERSONALITY MANUAL
CONTROL
INFORMATION BATTERY INTERNAL
PROGRAMS
BACK/EXIT UP DOWN ENTER
MAIN MENU SCREEN
SUBMENU SCREEN

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 16
Element ST Hex System Menu
DMX SETTINGS
001-XXX
DMX Lost Status
DMX Channel Mode
Selection
DMX Addressing
6ch / 7ch / 8ch / 11ch / 12ch
MENU OPTIONS DESCRIPTIONSUBMENU
DMX Address
DMX Channel
Mode
No DMX Status
Master
Hold Last / Blackout / Manual Settings /
Internal Programs
PERSONALITY
WiFly Settings
Set WiFly Channel: 00~14
Enable WiFly: YES / NO
Master Setting
Set WiFly Wireless Channel
Activate WiFly
Slave Setting
Dim Modes Dimming Curve Modes
Dimming Delay Speed
Standard/Stage/TV/Architectural/Theatre/Stage2
Dim Speed: 00 (No Delay), 1s ~ 99s
Display
Screen Saver Delay: OFF, 1~10S Display Blackout Time
Touch Screen Lock: OFF / 1~30S / 1 Minute Display Control Lock
Service Factory Restore: YES / NO Restore Factory Settings
Slave
ON / OFF
ON / OFF
WiFly On with Power: YES / NO WiFly Active with Power
Disable WiFly: YES / NO Deactivate WiFly
Rotate Display 180˚: YES / NO Display Inversion
Passcode = 011
Language Passcode = 050 English / Spanish
Manual Control
Red
Green
Blue
White
Amber
UV
Color Macros
Strobe
Master Dimmer
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
000-255
MANUAL
CONTROL
INTERNAL
PROGRAMS
Program 0
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Program 8
Program 9
Program 10
Program 11
Program 12
Program 13
Program 14
Program 15
Program 0 with Adjustments
Program 1 with Adjustments
Program 2 with Adjustments
Program 3 with Adjustments
Program 4 with Adjustments
Program 5 with Adjustments
Program 6 with Adjustments
Program 7 with Adjustments
Program 8 with Adjustments
Program 9 with Adjustments
Program 10 with Adjustments
Program 11 with Adjustments
Program 12 with Adjustments
Program 13 with Adjustments
Program 14 with Adjustments
Program 15 with Adjustments
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
Speed: 01~16 / Fade: 00~16 / Sound: ON / OFF
INFORMATION
LED Temperature XXX ˚C / XXX ˚F
Software Version X.XX
Charging Time X.Xhours
Current Life XXX%
Load Switch ON / OFF
BATTERY
Displayed Language
Current LED Temperature
Current Software Version
Current Charge Time
Current Battery Life
Activate/Deactivate Output
USB Port Power: YES / NO USB/Service Port Activation
Operation Mode Standard 4 / Saver 6 / Saver 8 Current Battery Mode

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 17
Element ST Hex System Menu
DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: DMX Address, DMX
Channel Mode, and No DMX Status.
- DMX ADDRESS MODE - In this submenu you are able to nd and set your desired DMX address.
- DMX CHANNEL MODE - In this submenu you are able to nd and set your desired DMX channel
mode.
- NO DMX STATUS - This setting is used as a precaution mode in case the DMX signal is lost or
interrupted. The operating mode chosen is the running mode the xture will go into when the DMX
signal is lost. Listed below are the 4 modes.
• HOLD LAST - This setting will have the xture stay in the last DMX setup.
• BLACKOUT - This setting will have the xture automatically go into blackout mode.
• MANUAL SETTINGS - This setting will have the xture automatically revert to your manual settings.
• INTERNAL PROGRAM - This setting will have the xture automatically run 1 of 15 (0-15) internal
programs.
PERSONALITY - The submenus listed under PERSONALITY are as follows: Master, Slave, Dim
Modes, WiFly Settings, Display, Language, and Service.
- MASTER - Set the unit to act as the Master unit in a master-slave set up.
- SLAVE - Set the unit to act as a slave unit in a master-slave set up.
- DIM MODES - In this submenu you are able to set your desired dimmer mode or adjust and set
your desired dimming speed.
- DISPLAY - In this submenu you are able to set your display blackout time, touch screen lock time,
and invert the display.
- LANGUAGE - In this submenu you are able to select your desired display language.
- SERVICE - In this submenu you are able to reset the unit to its factory/default settings.
MANUAL CONTROL - This submenu is for manual control and testing.
INTERNAL PROGRAMS - This menu allows you to select 1 of 15 (0-15) internal programs to run. The
internal program speed and fade speeds are adjustable. The internal programs can also be run as
sound active.
INFORMATION - The submenus listed under INFORMATION are as follows: LED Temperature and
Software Version.
- LED TEMPERATURE - This submenu allows you to check the current LED temperature.
- SOFTWARE VERSION - This submenu allows you to check the current software version.

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 18
BATTERY - The submenus listed under BATTERY are as follows: Charging Time, Current Life,
Operation Mode, and Load Mode.
- CHARGING TIME - This submenu is used when charging the unit. It allows you to check the
status of the charging time.
- CURRENT LIFE - This submenu allows you to check the battery life.
- OPERATION MODE - In this submenu you are able to select and set your desired energy saving
mode.
- LOAD MODE - In this submenu you are able to activate/deactivate the LED PCB output.
NOTE: This function needs to be activated when using battery power or AC power. For faster
charging switch this setting to “OFF”.
Element ST Hex System Menu
Element ST Hex WiFly Master-Slave Set Up
WiFly Master-Slave Set Up:
This function will allow you to link units together via WiFly to run in a Master-Slave setup.
1. Follow the system menu diagrom on page 16 to set the WiFly address and to activate WiFly. The
addresses on each fixture must be the same.
2. After you have set the WiFly address, select your “MASTER” unit. Activate the “MASTER” setting
by following the system menu diagram on page 16.
3. Set the “MASTER” unit to your desired mode of operation. On the “SLAVE” unit(s) follow the system
menu diagram on page 16 to activate the “SLAVE” setting.
4. If everything is set up correctly, the “SLAVE” unit(s) will start following the “MASTER” unit.
Element ST Hex WiFly Set Up
This unit can only be controlled using WiFly. Your DMX controller must be connected to a ADJ
WiFly Transceiver to use this function. You are able to communicate up to 2500 feet/760 meters
(open line of sight).
1. Follow the system menu diagram on page 16 to set the WiFly address and to activate WiFly. The
address must match the address set on the WiFly Transceiver.
2. After you have set the WiFly address, follow the system menu diagram on page 16 to select your
desired DMX Channel mode and set your DMX address.
3. Apply power to the WiFly Transceiver. The fixture must be set up first before you apply power to
WiFly Transceiver.
4. If everything is set up properly and the fixture is receiving a Wireless signal, you should now be
able to control it with a DMX controller.

ADJ Products, LLC - www.adj.com - Element ST Hex User Manual Page 19
Element ST Hex UC IR & Airstream Control
The UC IR infrared remote gives you control of various functions (See below). To control the fixture
you must aim the remote at the front of the fixture and be no more than 30 feet away.
The Airstream IR remote transmitter plugs into the headphone jack of your iOS phone or tablet. To
control your IR fixture you must raise the volume to the maximum on your iOS phone or tablet and
aim the transmitter at the fixture sensor and be no more than 15 feet away. After you have purchased
the Airstream IR transmitters, the app is a free download from the app store for your iOS phone or
tablet. The app comes with 3 pages of control depending on the fixture you are using. Please see
below for the IR functions including the corresponding app page.
Standby
FullON Fade/Gobo 
Strobe Color 
1 2 3
4 5 6
7 8 9
SoundOn Show0 SoundO
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the button again to return to the initial
state.
FULL ON -Press this button to fully light up the unit.
FADE/GOBO -This button can activate the internal programs. Use the numeral buttons 1-9 to select
the program number. Use the dimmer buttons to adjust the output intensity. Note: Running speed is
not adjustable using the IR control functions.
Example: Press the numeral buttons “1+3” to run program “13”.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity.
STROBE - Press this button to activate strobing. Use buttons 1-4 to adjust the strobe speed. “1”
being the slowest, “4” being the fastest.
COLOR - Press this button to activate color macro mode. Use the numeral buttons 1-9 or a combination
of two numbers to select your desired color. Example: Press the numeral buttons “1+3” to select color
macro “13”.
Numeral Buttons 1-9 - Use buttons 1-9 to select your desired color in color macro mode or internal
program in internal program mode.
SOUND ON & OFF - Use the buttons to activate and deactivate sound active mode.
SHOW 0 - This button is used with the numeral buttons to select your desired color in color macro
mode or program in internal program mode.