ADJ Focus Spot 5Z User manual

User Instructions
FOCUS SPOT 5Z
USA# FOC520
EU# 123000300
UPC# 818651028201

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-
ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
©2020 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation
of this product.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with
the included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
· Reorient or relocate the device.
· Increase the separation between the device and the receiver.
· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
05/13/20 1 1.0.3 19/22/26 Initial Version
Date Document
Version
Software
Version > DMX Channel Mode Notes

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 2
Focus Spot 5Z Table of Contents
Introduction
Features I Warranty Registration
Safety Guidelines
Installation
Overview
DMX Set Up
DMX Addressing
DMX Modes & Values
System Menu
Dimmer Mode Chart I Dimmer Curve Chart
Dimensional Drawings
Gobo Replacement I Gobos
Fuse Replacement I Multiple Unit Power Linking
Trouble Shooting I Cleaning
Limited Warranty (USA Only)
Technical Specications
3
4
5
8
10
11
13
14
20
26
27
28
29
29
30
31

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 3
Focus Spot 5Z Introduction
Unpacking: Thank you for purchasing the Focus Spot 5Z by ADJ Products, LLC. Every unit has been
thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are missing, please contact our toll free
customer support number for further instructions. Do not return this unit to your dealer without rst
contacting customer support.
Introduction: The Focus Spot 5Z is a DMX intelligent, moving head, LED fixture. This xture can be
used in a stand alone mode or connected in a Master/Slave conguration. This product is intended to
be used by professionally trained personnel only and is not suitable for private use.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit
forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit http://parts.americandj.com
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [email protected]
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]
www.adj.eu | [email protected]
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.

Focus Spot 5Z Features
Focus Spot 5Z Warranty Registration
The Focus Spot 5Z carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,
you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-
tacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the
shipper.
ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 4
• Individual Color and Gobo Wheels
• 2 x Color Wheels: 8 Colors + White (Each Wheel)
• 6 Rotating Replaceable Gobos + Open
• 2 Separate Frost Filters
• 2 Separate Rotating Prisms (6 Facet Circular Prism & 5 Facet Linear Prism)
• Adjustable Dimmer Modes, Dimming Speed, and Dimmer Curves
• 5-Pin DMX Connections
• 3 DMX Channel Modes: 19/22/26
• Electronic Dimming 0-100%
• DMX-512 protocol
• Multiple Unit Power Linking (See page 29)
Included:
1 x Locking Power Cable
1 x Omega Bracket
1 x Safety Cable

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 5
Focus Spot 5Z Safety Guidelines
• DO NOT TOUCH the xture housing during operation. Disconnect the power and allow approximately
15 minutes for the xture to cool down before servicing.
• DO NOT shake the xture, avoid brute force when installing and/or operating the xture.
• DO NOT operate the xture if the power cord has become frayed, crimped and/or damaged. If the
power cord is damaged, replace immediately with a new one of similar power rating.
• DO NOT Do not attempt to remove or break o the ground prong from the electrical cord. This
prong is used to reduce the risk of electrical shock and re in case of an internal short.
• DO NOT attempt to operate this unit, if it becomes damaged.
• DO NOT spill water or other liquids into or on to your unit.
• This unit is intended for indoor use only, use of this product outdoors voids all warranties.
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Disconnect from main power before making any type of connection.
• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.
Allow approx. 6” (15cm) between xture and other devices or a wall for proper cooling.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• During the initial operation of this xture, a light smoke or smell may emit from the interior of the
xture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning
o from the heat. This will decrease gradually over time.
• DO NOT remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 29
for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the fixture.
C. The fixture has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.
E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 6
Focus Spot 5Z Safety Guidelines
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.
AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH
OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE
DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE
DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 7
Focus Spot 5Z Safety Guidelines
POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS
External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,
glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.
This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures
from all manufacturers. Although there is no true way to fully prevent this issue from happening, the
guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service
for more details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT
SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,
INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 8
Focus Spot 5Z Installation
Screw one clamp via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners of the
Omega bracket into the respective holes on the bottom of the Focus Spot 5Z. Tighten the quick-lock
fasteners fully clockwise. Pull the safety cable through the opening located on the base plate and
over the trussing system or a safe xation spot. Insert the end in the carabine and tighten the safety
screw.
NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚C.
Do not place this lighting xture in an enviroment where the temperatures are under or above the
temperatures stated above. This will allow the xture to run at its best and help prolong the xture
life.
OMEGA
BRACKET
CLAMP
(Not Included)
OMEGA BRACKET
ATTACHMENT POINTS
SAFETY CABLE
ATTACHMENT POINTS

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 9
Focus Spot 5Z Installation
The Focus Spot 5Z is fully operational in three dierent mounting positions, hanging upside-down
from a ceiling or trussing, sideways on trussing, or set on a at level surface. Be sure this xture is
kept at least 12m (40ft) away from any ammable materials (decoration etc.). Always use and install
a safety cable as a safety measure to prevent accidental damage and/or injury in the event the
clamp fails (see previous page). Never use the carrying handles for secondary attachment.
When installing the unit, the trussing or area of installation must be able to hold 10 times the weight
without any deformation. When installing the unit must be secured with a secondary safety attachment,
e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or
servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation
material being used, and perodic safety inspection of all installation material and unit. If you lack
these qualications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 10
Focus Spot 5Z Overview
1. Service Port
2. LED Display
3. Mode Button
Up Button
Down Button
Left Button
Right Button
Enter Button
4. Locking Power Connector In
5. Fuse Holder
6. Locking 5-Pin XLR Connector Out
7. Locking 5-Pin XLR Connector In
8. Locking Power Connector Out
1
32
4 5 6 7 8

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 11
Focus Spot 5Z DMX Set Up
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Spot 5Z can be controlled
via DMX-512 protocol. The DMX address is set on the front panel of the Focus Spot 5Z. Your unit and your
DMX controller require a 5-pin XLR connector for data input and data output. We recommend Accu-Cable
DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable
(This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male
and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
Notice: Be sure to follow gures one (1) and two (2) when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could
cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 1
Figure 2
1 Ground 1 Ground
XLR Male Socket XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 12
Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator
on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected
between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female
XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ
part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Focus Spot 5Z DMX Set Up
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 3
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmission in
place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting standard
5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available
at most electric stores. The chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 13
All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.
You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures
simultaneously.
If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.
In the case of the Focus Spot 5Z, when in 19 channel mode you should set the starting DMX address
of the rst unit to 1, the second unit to 20 (19 + 1), the third unit to 39 (20 + 19), and so on. (See the
chart below for more details.)
Focus Spot 5Z DMX Addressing
Channel Mode Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
19 Channels 1 20 39 58
22 Channels 1 23 45 64
26 Channels 1 27 53 79

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 14
Focus Spot 5Z DMX Modes & Values
1 1 PAN MOVEMENT (8-BIT)
Pan Movement
2PAN FINE (16-BIT)
Fine Control of Pan Movement
3 3 TILT MOVEMENT (8-BIT)
Tilt Movement
4TILT FINE (16-BIT)
Fine Control of Tilt Movement
5 5
COLOR WHEEL 1
Functions
Standard (22) Extend (26) Values
Open / White
Red
Orange
Yellow
Green
Dark Blue
Purple
Light Blue
Magenta
Color Indexing
Clockwise Rotation Fast - Slow
No Rotation
Counter-Clockwise Rotation Slow - Fast
000-007
008-014
015-021
022-028
029-035
036-042
043-049
050-056
057-063
064-127
128-189
190-193
194-255
000-255
000-255
000-255
000-255
Basic (19)
3
1
2
COLOR WHEEL 2
Open / White
Lavender
Blue
CTB 5600
Green
Yellow
UV
CTO 3200
Pink
Color Indexing
Clockwise Rotation Fast - Slow
Stop
Counter-Clockwise Rotation Slow - Fast
000-007
008-014
015-021
022-028
029-035
036-042
043-049
050-056
057-063
064-127
128-189
190-193
194-255
ADJ FOCUS SPOT 5Z
DMX Channel Values & Functions
Supports Software Version > 1.0.3
Feature subject to change without notice
*Rotation direction (Clockwise/Counter-Clockwise) and control of effects depends on head orientation and Pan/Tilt settings*
6 64
2
4

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 15
Focus Spot 5Z DMX Modes & Values
7 7
GOBO WHEEL
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 1 Shake (Slow-Fast)
Gobo 2 Shake (Slow-Fast)
Gobo 3 Shake (Slow-Fast)
Gobo 4 Shake (Slow-Fast)
Gobo 5 Shake (Slow-Fast)
Gobo 6 Shake (Slow-Fast)
Clockwise Rotation Fast-Slow
No Rotation
Counter-Clockwise Rotation Slow-Fast
000-004
005-019
020-034
035-049
050-064
065-079
080-094
095-109
110-124
125-139
140-154
155-169
170-189
190-221
222-223
224-255
5
8 86
GOBO ROTATION
Indexing
Clockwise Rotation (Fast-Slow)
No Rotation
Counter-Clockwise Rotation Slow-Fast)
000-127
128-189
190-193
194-255
SHUTTER & STROBE
Shutter Closed
Shutter Open
Strobe Slow-Fast
Shutter Open
Pulse Effect Slow-Fast
Shutter Open
Random Strobe Slow-Fast
Shutter Open
000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255
997
Functions
Standard (22) Extend (26) ValuesBasic (19)
MASTER DIMMER
0%-100%
000-255
DIMMER FINE (16-BIT)
0%-100%
000-255
10 108
11

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 16
Focus Spot 5Z DMX Modes & Values
PRISM 2 (5 FACET LINEAR)
Open
Shutter Open
000-031
032-255
PRISM 2 INDEXING & ROTATION
Indexing
Clockwise Rotation Fast-Slow
No Rotation
Counter-Clockwise Rotation Slow-Fast
000-127
128-189
190-193
194-255
PRISM 2 FINE INDEXING (16-BIT)000-255
13 15
14 1612
17
11
FOCUS
Far-Near
000-255
ZOOM
Minimum-Maximum Beam
000-255
FROST 1
0%-100%
000-255
FROST 2
0%-100%
000-255
15 1813
16 1914
21
18 2216
1715
ZOOM FINE INDEXING (16-BIT)000-25520
Functions
Standard (22) Extend (26) ValuesBasic (19)
PRISM 1 (6 FACET CIRCULAR)
Open
Shutter Open
000-031
032-255
PRISM 1 INDEXING & ROTATION
Indexing
Clockwise Rotation Fast-Slow
No Rotation
Counter-Clockwise Rotation Slow-Fast
000-127
128-189
190-193
194-255
PRISM 1 FINE INDEXING (16-BIT)000-255
11 129
12 1310
14

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 17
Focus Spot 5Z DMX Modes & Values
DIMMER CURVES
Linear
Square
Inverse Square
S-Curve
No Function
000-020
021-040
041-060
061-080
081-255
PAN/TILT SPEED
Fast-Slow
000-255
20 24
21 2518
Functions
Standard (22) Extend (26) ValuesBasic (19)
DIMMER MODES:
Standard
Stage
TV
Architectural
Theatre
Stage 2
DIMMING SPEED
0.1Sec.
0.2Sec.
0.3Sec.
0.4Sec.
0.5Sec.
0.6Sec.
0.7Sec.
0.8Sec.
0.9Sec.
1.0Sec.
1.5Sec.
2.0Sec.
3.0Sec.
4.0Sec.
5.0Sec.
6.0Sec.
7.0Sec.
8.0Sec.
9.0Sec.
10Sec.
Default to Unit Setting
000-020
021-040
041-060
061-080
081-100
101-120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141-255
19 23

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 18
Focus Spot 5Z DMX Modes & Values
22 2619
LED REFRESH RATE & SPECIAL FUNCTIONS
Default LED Refresh Rate 1200Hz
Refresh Rate (Hz)
900
910
920
930
940
950
960
970
980
990
1000
1010
1020
1030
1040
1050
1060
1070
1080
1090
1100
1110
1120
1130
1140
1150
1160
1170
1180
1190
1210
1220
1230
1240
1250
1260
1270
1280
1290
1300
1310
1320
1330
1340
1350
1360
1370
1380
1390
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
Functions
Standard (22) Extend (26) ValuesBasic (19)
000-010
011-078

ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 19
Focus Spot 5Z DMX Modes & Values
22 2619
LED REFRESH RATE & SPECIAL FUNCTIONS
1400
1410
1420
1430
1440
1450
1460
1470
1480
1490
1500
2500
4000
5000
6000
10,000
15,000
20,000
25,000
Disable LED Refresh Rate
Enable Blackout with Pan/Tilt Movement
Disable Blackout with Pan/Tilt Movement
Enable Blackout with Color Change
Disable Blackout with Color Change
Enable Blackout with Gobo Change
Disable Blackout with Gobo Change
Reset All
Reset Pan/Tilt
Reset Color & Gobo
Reset Effect & Focus
Internal Program 1 (Scenes 1-8)
Internal Program 2 (Scenes 9-16)
Internal Program 3 (Scenes 17-24)
Internal Program 4 (Scenes 25-32)
Internal Program 5 (Scenes 33-40)
Internal Program 6 (Scenes 41-48)
Internal Program 7 (Scenes 49-56)
Fan Mode Low
Fan Mode High
Fan Mode Auto
No Function
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
080-089
090-099
100-109
110-119
120-129
130-139
140-149
150-159
160-169
170-179
180-185
186-191
192-197
198-199
200-205
206-211
212-216
217-227
228-238
239-249
250-255
Functions
Standard (22) Extend (26) ValuesBasic (19)