ADJ 3D Vision User manual

3D Vision
©2016 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions hereinare
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers hereinaretrademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters ofcopyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJProducts,LLCandallaffiliatedcompaniesherebydis-
claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi-
rect economic loss associated with the use or reliance of any
information contained within this document, and/or asa result
ofthe improper,unsafe, unsufficientandnegligentassembly,
installation, rigging, and operation of this product.
9/16
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn off all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

ADJ Products,LLC - www.adj.com - 3D VisionInstruction Manual Page 2
ADJ Products,LLC - www.adj.com - 3D Vision Instruction Manual Page 3
Unpacking: Thank you for purchasing the 3D Vision by ADJ Prod-
ucts, LLC. Every 3D Vision has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damageandbe sureallaccessoriesnecessarytooperatetheunithas
arrived intact. In the case damage has been found or parts are miss-
ing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contact-
ing customer support.
Introduction:The 3D Vision is a Hexagonal shaped LED panel with
stunning 3D visual effects when used in multiples. This LED panel is
controlled via DMX control. Kling-Net or Art-Net can be used when
used with EZKling. Dynamiceffects can be playedon it,whichmakes
it agreatsystemfor DJ’sand night clubs.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com
Warning!Toprevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution!There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
To optimize the performance of this product, please read these operat-
ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
• CAT 5 Straight Network Cable included.
• 75 x 5050 SMD 3-in-1 RGB LED’s
• Safety Cable Included
The 3D Vision carriesa2 year (730 days) limited warranty. Please fill
out the enclosed warranty card to validate your purchase and war-
ranty.You may also register your product online at www. americandj.
com.All returned service items whether under warranty ornot, must
be freight pre-paid and accompany a return authorization (R.A.) n um-
ber. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact ADJ customer support for a
R.A. number.
3D Vision
Warranty Registration
3D Vision
Features
3D Vision
General Instructions
3D Vision
Introduction

ADJ Products,LLC - www.adj.com - 3D VisionInstruction Manual Page 4
ADJ Products,LLC - www.adj.com - 3D Vision Instruction Manual Page 5
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 9 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
ding amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Control Using a DMX Controller:
1. The 3DVisionhas 9 DMX channels. See page 11for detailed
descriptionoftheDMXvaluesandtraits.Seethepage7forthe
pixel layout.
1. Toset a DMX address you will need touse the 3D VisionEncoder
(Sold Separately). Follow the instructions included with your 3D
Vision Encoder to set your desired DMX address.
2. When connecting to a DMX controller or using MyDMX, you will
needto use aRJ45 to3pin adapter.This can be purchased
through ADJ.
3. Connect the first unit to the adapater and then connect to either
your DMX controller or MyDMX.
4. Follow the DMX traits on page 11 to control your unit.
Do not daisy-chain morethan 32 Panels when connecting directly
to a DMX controller.
3D Vision
Operation
3D Vision
Safety Precautions

ADJ Products,LLC - www.adj.com - 3D VisionInstruction Manual Page 6
ADJ Products,LLC - www.adj.com - 3D Vision Instruction Manual Page 7
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attach-
ment, e.g. included safety cable. Never stand directly below the unit
when mounting, removing,orservicingthe unit.
Overhead mounting requires extensive experience, including calculat-
ing working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
The installaiton should be checked by a skilled person once a year.
Toconnect your3DVisionstooneanotheryoucanuseaquick
release panel lock (sold separately). To use the quick release panel
lock simply squeeze the ends of the quick release panel locks inwards
and attach to one of the six outer rigging bar attachment points. You
canuseaproclampwith10Mboltattachedtotherearmiddleofthe
unit (as seen below) to attach to trussing. See the next page for all
rigging areas and quick release connections.
10M threaded mounting hole
(toattachproclamptolockontruss)
quick release panel lock
to connect adjoining panels
crosshole (to
hang on astud or
hook)
Rigging bar attachment points
Checkthe rearofthe unit forthe word TOPtolocatethetopof
the unit. The top of the unit is Pixel 1.
Pixel 2
Pixel 1
Pixel 3
3D Vision
Pixel Layout
3D Vision
Mounting and Grouping
3D Vision
Mounting and Grouping

ADJ Products,LLC - www.adj.com - 3D VisionInstruction Manual Page 8
ADJ Products,LLC - www.adj.com - 3D Vision Instruction Manual Page 9
With this feature you can connect the fi es to one another
using the PowerCon input and output sockets. the quantity that
can be connected is 130 fixtures maximum @ 120V and 260 fix-
tures maximum @ 230V. After you have reached the maximum
amount of fixtures you will need to use a new power outlet. They
must be the same fixtures. DO NOT mix fixtures.
3D Vision Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
1. Usenormalglasscleanerandasoftclothtowipedownthe
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
80.5mm/3.16”
Listed below are a few common problems the user may encounter,
with solutions.
Unit is not receiving data;
1. Besure youare usinga CAT 5 Straight Network cable.
If problems are not resolved; Contact ADJ for service.
1-800-322-6337
3D Vision
Trouble Shooting
3D Vision
Power Cord Daisy Chain
3D Vision
DMX Traits
3D Vision
CAD Drawing
142.8mm/5.62”
119mm/4.68”
404.7mm/15.93”
150mm/5.90”
350.7mm/13.80”
Channel
Value
Function
1
0 - 255
RED 1
0% - 100%
2
0 - 255
GREEN 1
0% - 100%
3
0 - 255
BLUE 1
0% - 100%
4
0 - 255
RED 2
0% - 100%
5
0 - 255
GREEN 2
0% - 100%
6
0 - 255
BLUE 2
0% - 100%
7
0 - 255
RED 3
0% - 100%
8
0 - 255
GREEN 3
0% - 100%
9
0 - 255
BLUE 3
0% - 100%