ADTEK CS2-CT User manual

CS2-CT-2010-10-03 C2-17-1/8
CS2-CT MULTIFUNCTION Counter (Pulse input)
DESCRIPTION
The CS2-CT provides high speed and multifunction, counting,
control and communication (Modbus RTU mode) of Pulse from flow
meter or encoder, proximity switch, photo switch for length control.
There are 3 external control input (DI) in standard and the optional 4
Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also
support N, R, C mode for totalizer control.
FEATURE
●Measuring Pulse 0.01Hz~20KHz(optional: over 20KHz~50KHz); Contact / NPN / PNP / Voltage Pulse can be
switch on rear of meter
●4 banks pre-set for all relay functions relative 4 difference application, and selectable by 3 External Control
Inputs(E.C.I.) or front key in optional
●4 relay can be individual programmed for N/R/C mode and energized time.
●3 external control input can be individual programmed for Reset, Gat
●Analogue Output and RS485(Modbus RTU mode) available in option
●Comply to CE standard & RoHS
ORDERING INFORMATION
CS2−CT−
Input Range −Relay
Output −Analogue Output −
RS 485 Port
−
Pulse
Output −
AUX.
POWER
CODE INPUT RANGE
CODE REALY O/P CODE
A
NALOG O/P CODE RS 485 PORT CODE PULSE O/P CODE AUX. POWER
C Mech. contact
N None NNone
NNone NNone
A
A
C 115/230 V
N NPN R2 2 Rela
y
8RS 485 CO
p
en Collect
P PNP R3 3 Rela
y
V0(1) ~ 5 V
0 ~ 10 V
RRela
y
Contact
V
Volta
g
e
p
ulse
R4 4 Rela
y
ADH AC 85~264V
DC 100~300V
05 5V
p
ulse I 0 ~ 10 mA
0(4)~20 mA
ADL
A
C/DC 20~56V
12 12V
p
ulse
24 24V
p
ulse
O xx Specify
* If the pulse output is
to be selected, the
meter can be
selected 3 relay
maximum.
Energized mode: N / R / C Mode
TECHNICAL SPECIFICATION
Period of Relay on: 0:00.0~9(Minutes):59.9(Second)
Input
DO function: Energized by RS485 command of master.
Input Frequency Input Mode Input Level
Banks pre-set:
0.01Hz ~ 50 Hz Mech. Contact
NPN
4 banks pre-set for all relay functions to relative 4
difference control condition, and selectable by 3 External
Control In
p
uts
(
E.C.I.
)
or front ke
y
PNP
High Level: 8~12V; Low Level: 0.0~4.0 V
(with excitation supply 12Vdc)
Voltage Pulse High Level: over 2/3 of input level
Low Level: under 1/3 of input level
External Control Inputs(ECI)
0.01Hz ~ 50 Hz
0.01Hz ~ 100KHz
0.01Hz ~ 140KHz
(optional)
Pick U
p
Sensor S
p
ecified b
y
order
Input mode: 3 ECI points, Contact or open collect input, Level trigger
Functions: Gate / Reset / Offset / Bank selection(option) programmable
Input Mode(NPN, PNP, Contact) & Level(5Vp, 12Vp, 24Vp) changeable
b
y
di
p
switch of rear terminal block.
Debouncing time: Settable range 5 ~255 x (8m seconds)
Input range: 0.01Hz~20kHz (~50kHz in option)
Sampling time: 0.05 m-second~100 seconds (0.02 m-second in option)
Analogue output(option)
Response time: ≤100 m-sec.(when the AvG = “1”) in standard Accuracy: ≤±0.1% of F.S.; 16 bits DA converter
Ripple: ≤±0.1% of F.S.
Response time: ≤100 m-sec. (10~90% of input)
Display & Functions
Isolation: AC 2.0 KV between input and output
LED: Numeric: 5 digits, 0.8”(20.0mm)H red high-brightness LED Output range: Specify either Voltage or Current output in ordering
Relay output indication: 4 square red LED Voltage: 0~5V / 0~10V / 1~5V programmable
RS 485 communication: 1 square orange LED Current: 0~10mA / 0~20mA / 4~20mA programmable
E.C.I. function indication: 3 square green LED Output capability: Voltage: 0~10V: ≥1000Ω;
Display range: 0.0000~99999 with auto moving of decimal point Current: 4(0)~20mA: ≤600Ωmax
Factor Setting: Functions: aOhs(output range high): Settable range: -19999~99999
Settable Range: -19999~+99999 with decimal point
settable 0 / 0.0 / 0.00 / 0.000 / 0.0000
aOls(output range Low): Settable range: -19999~99999
Decimal Point: Settable: 0 / 0.0 / 0.00 / 0.000 / 0.0000
aOlmt (output High Limit): 0.00~110.00% of output High
Over Flow indication: Overflow ovfl/ Re-cycle rcycl counting programmable Digital fine adjust: aOzro: Settable range: -38011~+27524
Compensation setting: Option: Settable range: -19999~+99999 aOspn: Settable range: -38011~+27524
Digital adjustment: Option: cTspn: Settable range: -19999~99999
Control Functions(option)
Set-points: Four set-points
Control relay: Four relays
Relay 2 & Relay 3: Dual FORM-C, 5A/230Vac, 10A/115V
Relay 1 & Relay 4: Dual FORM-A, 1A/230Vac, 3A/115V
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S
OPTION OPTIONOPTION
OPTION 4
Input mode and level
can be changed by
dip switches on rear
of meter

CS2-CT-2010-10-03
C2-17-2/8
RS 485 Communication(option)
Protocol: Modbus RTU mode
INSTALLATION
Baud rate: 1200/2400/4800/9600/19200/38400 programmable
Data bits: 8 bits
The meter should be installed in a location that does not exceed the
maximum operating temperature and provides good air circulation.
Parity: Even, odd or none (with 1 or 2 stop bit) programmable
Address: 1 ~ 255 programmable
Remote display: to show the value from RS485 command of master
Distance: 1200M
Terminate resistor: 150Ωat last unit.
Electrical Safety
Dielectric strength: AC 2.0 KV for 1 min, Between Power / Input / Output / Case
Insulation resistance: ≥100M ohm at 500Vdc, Between Power / Input / Output
1.0~8.0 mm
FIX HOLDER:
104 mm(L) / W M3
R
RL
R
R
COM
C
C
C
ENT/FN
?
?
?
Kg/cm
2
PANEL CU
T
-OUT:
92+0.2(W) x 44+0.2(H) mm
Isolation: Between Power / Input / Relay / Analogue / RS485 / E.C.I.
EMC: EN 55011:2002; EN 61326:2003
Safety(LVD): EN 61010-1:2001
CONNECTION DIAGRAM
Environmental
Operating temp.: 0~60 ˚C
Operating humidity: 20~95 %RH, Non-condensing
Temp. coefficient: ≤100 PPM/˚C
Storage temp.: -10~70 ˚C
Enclosure: Front panel: IEC 549 (IP54); Housing: IP20
Mechanical
Dimensions: 96mm(W) x 48mm(H) x 120mm(D)
Panel cutout: 92mm(W) x 44mm(H)
Case material: ABS fire-resistance (UL 94V-0)
Mounting: Panel flush mounting
Terminal block: Plastic NYLON 66 (UL 94V-0)
D-S 1 2 3 4 5
NPN ON
PNP ON
M.C. ON ON
5VP
12VP ON
24VP ON
D-S is on, when it is
on down side.
21 22 24 2523 27 2826 29 30 31 33 32 34
Relay 3
b c a
Relay 2
b c a
Relay 1
a c
Relay 4
a c
Analogue
output
A B
RS 485
port
ECI1 ECI3 COMECI2
External
Control
Input
4 53 6 7 8 9 10 11 12 14 15 13
Terminal blocks:
10A/300Vac, M2.6,
M2.6, 1.3~2.0mm2
(16~22AWG)
A
C 86~265V
DC 100~300V
DC 20~56V
AC230V
AUX. POWER
AC115V
ADH
ADL
D-S
Dip-Switch
0
V
+
V
+IN
SIGNAL INPUT
Count
/
Pulse
FG
10A 300Vac, M2.6, 1.3~2.0mm2(16~22AWG)
Weight: 550g / 350g(Aux. Power Code: ADH or ADL)
Please check the voltage of power supplied first, and then connect to
the specified terminals. It is recommended that power supplied to the
meter be protected by a fuse or circuit breaker.
Power
Power supply: AC115/230V,50/60Hz;
Optional: AC 85~264V / DC 100~300V, DC 20~56V
Excitation supply: DC 12, 24V/40mA maximum in standard
Power consumption: 5.0VA maximum
Back up memory: By EEPROM
Power Supply
AC115/230V
AC85~264V
Filter or Transformer
L
N
G
L
N
G
1A Fuse
7 9 10 8
FRONT PANEL
Sensor input connection
D-S 1 2 3 4 5
NPN ON
PNP ON
Mech. Contact ON ON
Voltage pulse 5VP
Voltage pulse 12VPON
Voltage pulse 24VPON
D-S is on when it is in down site
11 12 14 15 13
+Vdc
Out
0V
+IN
0V +V
+Vdc
Out
0V
Please change the dip-switch on rear
of meter to match the input mode and
level.
RL1
RL
2
2
RL
3
RL
4
COM
CI11
CI2
CI3
ENT/FN
?
?
?
Comm. status
Relay status
Indication
Operation Key
Control Input
status
Engineer Unit
Display screen
DIMENSIONS
RS485 Communication Port
RS485 Port
30 31 32
A
B
Max. Distance: 1200M
Terminate Resistor
(at latest unit):
120~300ohm/0.25W
(typical: 150ohm)
92.0+0.2
44.0+0.2
PANEL CUT-OUT
96.0
48.0
FRONT VIEW
Unit: mm
8.0 12.0
100.0
Dimensions: 96mm x 48mm x 120mm
Panel Cutout: 93mm x 45mm (advise)
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S

CS2-CT-2010-10-03 C2-17-3/8
FUNCTION DESCRIPTION
Display & Functions
Factor:
The factor can be set from -19999 to 99999 with decimal point. It also
can be set 0.0001 as like as divider.
ON
Auto
Reset
Relay output Time
Totalizer
Set
Point
Relay
Output
C mode:
Totalizer auto reset & relay reset by time setting of
relay output time[ry_.ot]
It is very popular application to install an encoder to measure the running
length. The engineers normally know the factor is x length/pulse. It just sets
the x into the function to show the length on meter.
Digital adjustment(option):
When the condition of Set Point is met:
1. The relay will be energized, until the time is over
Relay output time [ry_.ot](Relay_ output
times).
2. The totalizer(±kWh) will be reset to “0”
immediatel
y
, then counts-u
p
from “0”.
Sometimes, the counter will display an error due to the structure of
machine or some reason. In the case, user can set the digital adjustment
to compensate the value.
Users can get Fine Adjustment for Span of counting by front key of
the meter, and “Just Key In” the value which user wants to show
the number.
The ad
j
ustment can be clear in function
[
CSCLr
]
.
Offset preset(Option):
ON
Relay
Output
Set
Point
Auto
Reset Totalizer
Relay output Time
DO function d o :
CS2-CT can set a value(ex. 200) in [oFset] of [input group]to
control the start counting value by external control input(E.C.I.) that has
been set oFset .
XThe counter will re-count from “0”, when the E.C.I is open.
XThe counter will re-count from “the value(200)”, when the E.C.I is
close
Over flow indication: ovFL ovfl/ Re-cycle rcycl counting programmable
The up screen will show the ovfl, if the [ofLmd]set to be ovfl.
And it will re-count from “0”, if the [ofLmd] set to be rcycl .
The function has been designed not only a meter but also an
I/O interface. In the case of motor control cabinet can't get the
remote function. It's very easily to get the ON/OFF status of
switch from CS2 series with RS485 function.
If the [ry_.md]had been set do , the relay will be
energized by RS485 command directly, but no longer to
com
p
are with set-
p
oint.
Control Functions(option)
External Control Inputs(ECI)
The 3 mode are very useful idea to control the totalizer. The relay
energized condition is according to not only energized level, but also time
and reset for totalizer.
Relay energized mode: N / R / C Mode programmable
Relay output time: Settable range from 0.0(s)~9(m)59.9(s)
The three external control inputs are individually programmable to perform
specific meter control or display functions. All E.C.I. have been designed in
level trigger actions. Please pay attention, the ECI1 or ECI2 input will be
disable while UP or Down Key has been set to be “ yes”.
N mode: Totalizer & relay reset by manual ECI Functions: Gate / Reset / Offset
Gate function: Totalizer will be stopped to accumulate, when ECI is closed,
until the ECI open again. The Totalizer count will accumulate
continuously after the ECI open.
When the condition of Set Point is met:
1. The relay will be energized;
2. The totalizer will run as same as usual, until
manual reset by front key or by ECI of rear
terminal, the totalizer will be reset to “0” and the
rela
y
will be de-ener
g
ized.
Gate for Totalizer
Totalize
r
Gate by ECI
O
N
Level Trigge
r
ON ON
ON
g
ate
[
e
cI_
]
Reset Function:
Set
Point
Relay
Output ON
Totalizer
Manual
Reset
Totalizer will be reset to “0”, when ECI is closed, until the ECI
open again. The Totalizer will accumulate from 0 after the ECI
open.
R mode:
Totalizer & relay reset by time setting of relay
output time [ry_.ot]
Reset for Totalizer(Energy)
Reset by ECI
Edge Trigger O
N
ON ON
Totalizer
(Energy)
r
eset
[
e
cI_
]
When the condition of Set Point is met:
1. The relay will be energized, until the time is over
Relay output time [ry_.ot](Relay _ output
times).
2. The totalizer will run as same as usual; until the
time is over Relay output time [ry_.ot](Relay _
output time),The totalizer will be reset to “0”.
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S

CS2-CT-2010-10-03
C2-17-4/8
Offset function: Fine zero & span adjustment: When the [oFset] in [input group] set to be 200:
Totalizer will be reset to “200”, when ECI is closed. The
Totalizer will count-up from 200.
Users can get Fine Adjustment of analogue output by front key of the
meter. Please connect standard meter to the terminal of analogue
output. To press the front key(up or down key) of meter to adjust and
check the output.
Zero adjust [aOzro]:Fine Zero Adjustment for Analog Output;
Settable range: -38011~27524;
Span adjust [aOspn]:Fine Span Adjustment for Analog Output;
Settable range: -38011~27524;
Reset for Totalizer(Energy)
Reset by ECI
Edge Trigger O
N
ON ON
Totalizer
reset
[
ecI_
]
200
[
ofset
]
RS 485 communication(option)
Banks selection function(option):
There are extra 3 banks can be selected by E.C.I.
E.C.I.1 close means bank 1 has been selected.
E.C.I.2 close means bank 2 has been selected.
E.C.I.3 close means bank 3 has been selected.
E.C.I. all open means bank 0 has been selected.
CS2 series supports Modbus RTU mode protocol to be used as Remote
Terminal Unit (RTU) for monitoring and controlling in a SCADA (Supervisor
Control And Data Acquisition) system. The baud rate can be up to 38400
bps. It's not only can be read the measured value and DI (external control
inputs) status but also controls the relays output (DO) by RS485
communication
p
orts.
Debouncing time:
The function is for avoiding noise signal to into the meter. And The basic
period is 8 m-seconds. It means you set the number that has to multiple
8 m-seconds.
For example:
[
debnc
]
set to be 5, it means 5 x 8mseconds = 40mseconds
Analogue output(option)
Please specify the output type either a 0~10V or 4(0)~20mA in ordering.
The meter offers one analogue output with Multi-Cross selection function.
User can program the output to correspond immediately value, totalizer,
batch and batch count, and also the output low and high can be
programmable which it's related to various display values easier in [ao
group].
Reverse slope output is possible by reversing point positions. Please refer
to the detail descri
p
tion as below,
CS2-CT & CS2-PR APPLICATION FOR FLOWNETER / PRESSURE MEASURING
RS 485 Modbus RTU Mode
(
u
p
to 38400b
p
s
)
Analo
g
Out
p
ut 0~10V/0
(
4
)
~20mA
3 External Control Input:
Functions: Relative PV / PV Hold / Reset Max or Mini.
Hold / DI / Reset for Relay Energized Hold
Application: Thermal Switch / Circuit Breaker / Push
Button / ……
Displa
y
:
Mode: Measuring Value / Maximum Hold / Minimum
Hold / Reading value from RS485 command
AL
AL
Flowmeter
RL
1
RL
2
RL
3
RL4
COM
ECI1
ECI2
ECI3
ENT/FN
◄ ▲ ▼
K
g
/
Pulse
RL
2
2
RL
3
RL4
COM
CI11
CI2
CI3
ENT/FN ◄ ▲ ▼
Output range: Voltage: 0~5V / 0~10V / 1~5V programmable
Remote Display:
Current: 0~10mA / 0~20mA / 4~20mA programmable
Functions: Output High / Low scale, output limit, fine adjustment
Output range high [ aOhs]:
To setting the Display value High to versus output range
High(as like as 20mA in 4~20)
The meter will show the value that received from RS485 command. In
past, The meter normally receive 4~20mA or 0~10V from AO or digital
output from BCD module of PLC .We support a new solution that PV
shows the value from RS485 command of master so that can be save
cost and wirin
g
from PLC.
Output range low [ aOls]:
To setting the Display value Low to versus output range
Low(as like as 4mA in 4~20)
When the [ dsply] set to be RS485, it means, the PV screen will show the
number from RS485 command & data. The data (number) will be same as
PV that will make the totalizer accumulate and compare with set-point,
analogue output and ECI functions so that is to control analogue output,
rela
y
ener
g
ized and so on.
CS2-CT APPLICATION FOR REMOTE DISPLAY FROM RS485 COMMAND
RS 485 Modbus RTU Mode (up to 38400bps)
RS485 wiring 1.2KM maximum
Terminate Resistor:
RL1
RL
2
RL
3
RL4
COM
ECI1
ECI2
ECI3
ENT/FN
◄
▲ ▼
Kg/cm
2
RL1
RL2
2
RL
3
RL4
COM
C
I11
CI2
C
I
3
ENT/FN ◄ ▲ ▼
Set Scaling: [ lOsc]: 0.00, [ hIsc]: 199.99;
Output: [ aOls]: 50.00(Display Value Low),
[ aOhs]: 150.00(Display Value High)
0.00% 100.00%50.00% OUTPUT
199.99
100.00
0.00
50.00
150.00
SCALE
[
aOls ]
[
aOhs ]
The range between [ aOhs]and [ aOls]should be over
20% of span at least; otherwise, it will be got less resolution of
analogue output.
Output High Limit [ aOlmt]:
0.00~110.00% of output High User can set the high limit of
output to avoid a damage of receiver or protection system.
Set Scaling: [ lOsc]: 0.00, [ hIsc]: 199.99;
Output: [ aOls]: 50.00(Display Value Low),
[ aOhs]: 150.00(Display Value High)
[aOlmt]: 80.00%( of Output Range)
0.00% 100.00%50.00%
OUTPUT
199.99
100.00
0.00
50.00
150.00
SCALE
Ao.LMt: 80.00%
80.00%
[
aOhs ]
[
aOls ]
[
aOlmt ]
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S

CS2-CT-2010-10-03 C2-17-5/8
OPTIONAL FUNCTION
Customize function with quantities is welcome. Please contact with our
sales for detail. The appendix code of optional function will be add
behind the code of auxiliary power as like as xxx-A-3BK.
BANK FUNCTION(Suffix-3BK)
●The function is for CS2 to control difference process with a same
meter.
●For example; a pressure testing equipment; it has to measure
multi-range with difference pressure transducers. The meter can be
pre-set 4 groups parameter to show difference scale and relay
energized in difference set-points. The operator just selects the
bank number (bank1) to meet the process (product A). To make
easier operating and to avoid mistake in process.
●The bank function is available in CS2-CT (optional) too. It’s useful to
control as like as filling machine, Air flow measurement with
difference sensor.
●4 banks pre-set for all relay functions relative 4 difference scaling,
decimal point, and select by 3 External Control Inputs(E.C.I.) or
front ke
y
.
●Example:
Product A: Flowmeter: 1.0000L/sec; Set-Point: 2.0000L
Output: RS485
Product B: Flowmeter: 5.000L/sec; Set-Point: 6.000L
Output: RS485
Setting:
BANK1: [d p ]: )0000 [ry!md]: totLr [ry!sp]: @0000
[ry!ot]: )0)50(M).00.5(S)
BANK2: [d p ]: )000 [ry!md]: totLr [ry!sp]: ^000
[ry!ot]: 0 )0!0 (M).01.0(S)
ECI.1: Bank.1 ECI.2: Bank.2;
connect to a selector (or DO of PLC) to ECI1 and ECI2
XThe order want to produce Product A, to switch selector to A(Label Aon
panel), and then ECI.1 close, the square green LED bright. The meter will
work base on the setting of bank1 and relay1 output on 2.0000.
XThe second order want to produce Product B, to switch selector to
B(Label Bon panel), and then ECI.2 close, the square green LED
bright. The meter will work base on the setting of bank2 and relay1
output on 6.000.
●Only 1 Bank can be selected. The priority is Bank1 > Bank2 > Bank3, if it
is double selection.
ERROR MESSAGE
BEFORE POWER ON, PLEASE CHECK THE SPECIFICATION AND CONNECTION AGAIN.
SELF-DIAGNOSIS AND ERROR CODE:
DISPLAY DESCRIPTION REMARK
ovfl Display is positive-overflow (Signal is over display range) (Please check the input signal)
-ovfl Display is negative-overflow (Signal is under display range) (Please check the input signal)
ovfl ADC is positive-overflow (Signal is higher than input range
high 20%) (Please check the input signal)
-ovfl ADC is negative-overflow (Signal is lower than input range low
-20%) (Please check the input signal)
eep
fail EEPROM occurs error (Please send back to manufactory for repaired)
aiCng
p v Calibrating Input Signal do not process (Please process Calibrating Input Signal)
aic
fail Calibrating Input Signal error (Please check Calibrating Input Signal)
aoCng
p v Calibrating Output Signal do not process (Please process Calibrating Output Signal)
aoc
fail Calibrating Output Signal error (Please check Calibrating Output Signal)
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S

CS2-CT-2010-10-03
C2-17-6/8
FRONT PANEL:
RL1
RL
2
2
RL
3
RL4
COM
CI11
C
I2
CI3
ENT/F N
?
?
?
M
Comm. status
Relay status
Indication
Operation Ke
y
Control Input
status
Engineer Unit
Display screen
Numeric Screens
●Up screen: 0.28”(0.71cm) red high-brightness LED for 10 digital
totalizer.
●Down screen: 0.28”(0.71cm) green high-brightness LED for
Immediate Value 4 2/3 digital or Batch 6 digital.
I/O Status Indication
●Relay Energized: 4 square red LED
RL1
display when Relay 1 energized;
RL
2
display when Relay 2 energized;
RL
3
display when Relay 3 energized;
RL4
display when Relay 4 energized;
●External Control Input Energized: 3 square green LED
ECI1
display when E.C.I. 1 close(dry contact)
ECI
2
display when E.C.I. 2 close(dry contact)
ECI3
display when E.C.I. 3 close(dry contact)
●RS485 Communication: 1 square red LED
CO
M
will flash when the meter is receive or send data, and CO
M
flash
quickly means the data transient quicker.
Stickers:
Each meter has a sticker what are functions and engineer label
enclosure.
●Relay energized mode: H
H
H i L
o
L
L D
O
●E.C.I. functions mode:
PV.H(PV Hold) / DI /
M.RS(Maximum or Minimum Reset) /
●Engineer Label: over 80 types.
Operating Key: 4 keys for
Enter(Function) /
Shift(Escape) /
Up key / Down key
Setting Status Function Index
Up key Increase number Go back to previous
function index
Down key Decrease number Go to next
function index
Shift key Shift the setting
position
Go back to this function
index, and abort the setting
Enter/Fun
key
Setting Confirmed
and save to EEProm
From the function index to
get into setting status
Pass Word:
Setting range:0000~9999;
User has to key in the right pass word so that get into【Programming
Level】. Otherwise, the meter will go back to measuring page. If user
forgets the password, please contact with the service window.
Function Lock: There are 4 levels selectable for lock.
●None none: no lock all.
●User Level user: User Level lock. User can get into User Level for
checking but setting.
●Programming Level eng: Programming level lock. User can get
into programming level for checking but setting.
●ALL a l l : All lock. User can get into all level for checking but
setting.
Front Key Function
●The
Key can be set to be the same function as the setting of ECI1.
Ex. The ECI1 set to be gate and the function [E1=up]set to be
yes in [eci group]. When user presses
Key, the PV will hold
as like as ECI1 close.
●The
Key can be set to be the same function as the setting of ECI2.
●Ex. The ECI2 set to be reset and the function [E2=dn]set to be
yes in [eci group]. When user presses
Key, the PV will show
relative value as like as ECI2 close.
XIf the front key function has been set, the terminal input for ECI
will be disabling.
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S

CS2-CT-2010-10-03 C2-17-7/8
OPERATING DIAGRAM (The detail description of operation, please refer to operating manual.)
Power ON
*****
Self-diagnosis
cs@ct
Show the model
number
0−1
10000
r
y!sp
ry!sp: Relay 1
Set-point
-19999~99999
0−4
10000
r
y
$
s
p
ry$sp: Relay 4
Set-point
-19999~99999
ver!0
Show
the firmware
version
0−2
10000
r
y@sp
ry@sp: Relay 2
Set-point
-19999~99999
0−5
v
er!
0
c
s@
c
t
model number
firmware
version
Checking only
999(9
ENT
MEASURING
PAGE
Press
1sec
Press
1sec
0−3
10000
r
y#sp
ry#sp: Relay 3
Set-point
-19999~99999
0−6
b
nk-
0
b
ank
Option
Bank: Bank
selection
bnk-0 / bnk-1 /
bnk-2 / bnk-3
enter
Pcode
ENT
Enter the
password to
access Engineer
Level
YES
Pass Code
NO
Default:1000
input
group
ENT
INPUT
GROUP
▲
▼
r
elay
g
roup
ENT
RELAY
GROUP
▲
▼
e
ci
g
roup
ENT
EXTERNAL
CONTROL
INPUT (E.C.I)
GROUP
▲
▼
ao
group
ENT
ANALOGUE
OUTPUT
GROUP
▲
▼
A−1
)0000
cnTdp
cnTdp: Decimal
Point of
Counting
0 / ) 0 /
)00 / )000 /
)0000
B−1
t
otLn
r
y!md
ry!md: Relay 1
energized mode
off / d o /
totLn / totLr /
totLc
C−1
g
ate
e
cI1
ecI1: External
Control Input 1
none / ofset /
reset / gate /
bKsel
D−1
A4-20
aOtyp
aOtyp:
Analogue Output
type selection
V0-10 / V 0-5 /
V 1-5 / A0-10 /
A0-20 / A4-20
A−2
!0000
cnTkf
cnTkf: Factor of
Counting
-19999~99999
B−2
)0)0
r
y!ot
ry!ot: Relay 1
energizing time
0.00.0~9(M).59.9(S
)
C−2
r
eset
e
cI
2
ecI2: External
Control Input 2
none / ofset /
reset / gate /
bKsel
D−2
0
aOls
aOls: Analogue
Low Output
versus Low
Scale
-19999~99999
A−3
0
ttLdp
ttLdp: Decimal
point of totalizer
0~0.0000
B−3
t
otLn
r
y@md
ry@md: Relay 2
energized mode
off / d o /
totLn / totLr /
totLc
C−3
n
one
e
cI3
ecI3: External
Control Input 3
none / ofset /
reset / gate /
bKsel
D−3
99999
aOhs
aOhs: Analogue
High Output
versus High
Scale
-19999~99999
A−4
rcycl
ofLmd
ofLmd:
Overflow Mode
ovfl / rcycl
B−4
)0)0
r
y@ot
ry@ot: Relay 2
energizing time
0.00.0~9(M).59.9(S
)
C−4
12
d
ebnc
debnc:
Debouching of
external control
Input
5~255(x8ms)
D−4
0
aOzro
aOzro: Fine Zero
Adjustment for
Analogue Low
Output
-38011~27524
A−5
0
cTspn
cTspn: Fine
High point
Adjustment for
counting
-19999~+99999
B−5
t
otLn
r
y#md
ry#md: Relay 3
energized mode
off / d o /
totLn / totLr /
totLc
C−5
n
o
E
1=up
E1=up: ECI.1 set
to be UP Key
function
yes / n o
D−5
0
aOspn
aOspn: Fine
Span Adjust. for
Analogue High
Output
-38011~27524
A−6
no
CSclr
CSclr: Clear
Fine Span
Adjustment for
PV display
yes / n o
B−6
)0)0
r
y#ot
ry#ot: Relay 3
energizing time
0.00.0~
9(M).59.9(S)
C−6
n
o
E
2
=
d
n
E2=dn: ECI.2 set
to be Down Key
function
yes / n o
D−6
none
ZSclr
ZSclr: Zero &
Span Clear for
Adjustment
none / aOzro /
aOspn / both
A−7
0
ofset
ofset:
Offset pre-set
-19999~99999
B−7
t
otLn
r
y$md
ry$md: Relay 4
energized mode
off / d o /
totLn / totLr /
totLc
D−7
11)00
aOlnt
aOlmt: Analog
Output High
Limit
0.00~110.00%
Next Page Next Page
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S
User Level
Press
for 1 sec. can back to Measuring
Pro
g
rammin
g
Level
Press
for 1 sec. can back to Measuring
▼
▲

CS2-CT-2010-10-03
C2-17-8/8
A−8
1000
Pcode
Pcode: Pass
Code for enter
Engineer Level
0000~9999
B−8
)0)0
r
y$ot
ry$ot: Relay 4
energizing time
0.00.0~9(M).59.9(S)
A−9
none
Flock
Flock: Function
Level Lock
none / user /
eng / all
rs485
group
ENT
RS485
GROUP
E−1
1
adres
adres: Device
number of the
meter
1~255
E−2
9600
baud
baud: Baud
rate
1200 / 2400 /
4800 / 9600 /
19200 / 38400
E−3
NstB2
prity
prity: Parity
NstB1 / NstB2 /
odd / even
XPlesae refer to operating manual for detail description
CSM-321S
CS2-
V
A
CSM-321S CSM-CSM-
CS2-CT
CSM-321S CSM-CSM-
CSM-321SCSM-
CSM-321S