ADTRAN SR700ac User manual

SR700ac
Quick Start Guide

Installation
1. Connect one end of the phone cable to the DSL port on the gateway and connect the other end to the phone jack
on the wall installed by your provider.
2. Connect one end of the Ethernet cable to a LAN port on the gateway and connect the other end to your computer.
3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gateway.
Turn on the unit by pressing the On/Off button on the back of the gateway.
4. If you plan to create an LTE connection, insert a SIM card into the SIM slot located under the WAN port.
Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to
complete before you can begin using your Internet applications (browser, email, etc.). If you are unable to connect to the
Internet, verify that all cable connections are in place and the gateway’s power is turned on.

POWERWANDSL 1 2 3 4
Reset
SIM
123
3

LED Indicators
The LEDs on the SR700ac gateway can help you better understand
the current state of your gateway.
Legend: Green Green blinking Red Red blinking
LED Action Explanation
All LEDs except those
listed below
Connection enabled.
Data being transferred.
DSL & WAN Not lit Connection dropped; attempting resynchronization.
POWER Device has power and is ready to use.
Power up test failure.
Note: This LED flashes red briefly on startup; this is normal.
INET Gateway online.
Data being transferred.
Connection dropped; attempting resynchronization.
Not lit IP connection failed.

5
LED Action Explanation
WPS WPS setup procedure in progress.
WPS connection completed.
No partner found for pairing.
Session overlap detected. Possible security risk.

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small
circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the
hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to the
factory defaults.
Logging in to your gateway
To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed the
steps in "Installation" before you begin.
1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.
2. Enter the factory default credentials shown below and click OK.
User Name: admin Password: admin
Note: Your service provider may use other settings. Contact your provider for details.
3. At the bottom of the page, click Manage gateway (advanced). The gateway interface appears.
Configuring the WAN manually
If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer2 Interface and WAN Service
sections of the SmartRG SR700ac Gateway User Manual to manually establish a connection.

7
Configuring an LTE Connection
1. With the gold contacts facing up, insert the SIM card containing the LTE information into the SIMslot on the back of
the gateway.
Note: The SR700ac gateway accepts a Standard SIM (15 x 25mm) card.
2. In the left navigation bar, click LTE WAN Service >Network Settings.
3. In the Network Dial Mode field, select the dial mode for this connection.

4. In the APN Name field, enter the APN for your network provider.
5. Click Save/Apply to apply your changes.
Note: It may take up to 90 seconds for the Save action to complete.
Your device should now be connected to your network via LTE.

9
WiFi Setup
Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the
instructions for the applicable method.
1. In the left navigation bar, click Wireless.
2. If the Enable Wireless option is not already selected, select it now.
3. Continue with your preferred method of wireless setup.

WPS Method
If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow
these steps.
1. In the left navigation bar, click Wireless.
2. Click the wireless band that you want to configure and then click Security.
3. In the Enable WPS field, select Enabled.