ADTRAN 414 RG User manual

Q
uic
k
Start
DESCRIPTION
The 424 ONT (Optical Network Terminal) and 414 RG ONT Fiber Tray and
Wall Mount Bracket (ONT Fiber Tray and Bracket) is used to mount either
of the following ONTs to a wall:
■ADTRAN 424 ONT 2 POTS/4 GigE (P/N 1287835F1)
■ADTRAN 414RG 2 POTS/4 GigE WiFi ONT (P/N 1287790F1)
The wall mount bracket also incorporates a fiber tray to store excess
incoming fiber should that be required.
Required Tools
The following tools are required to install the ONT Fiber Tray and Bracket.
■Power drill (optional)
■Carpenter’s level (optional)
■Phillips-head Screwdriver
■Hammer
Installation Steps
To install the ONT Fiber Tray and Bracket, complete the following steps:
1. Select Location and Mount Bracket
2. Attach Incoming Fiber Cable to Bracket
3. Attach ONT to ONT Fiber Tray and Bracket
4. Connect Incoming Fiber Cable to ONT
Step 1: Select Location and Mount Bracket
Select a location to mount the ONT Fiber Tray and Bracket near the fiber
entrance. Use the supplied hardware to mount the bracket to the wall as
follows:
gNOTE
Supplied hardware is intended for drywall mounting only. For mounting on
surfaces other than drywall, obtain the appropriate mounting hardware
and follow the provided instructions.
1. Refer to Figure 1 and mark hole locations using the ONT Fiber Tray
and Bracket as a template. Use a carpenter’s level to ensure the
bracket is level.
2. Start anchor into the wall by using a hammer to lightly tap the
anchor in until the threads are close to the wall
gNOTE
Pre-drill holes using a 1/4” drill bit if difficulty is encountered.
3. Using a Phillips-head Screwdriver, apply gentle forward pressure on
the wall anchor and rotate it clockwise until the collar of the wall
anchor is flush with the wall.
4. Align the ONT Fiber Tray and Bracket with the anchors. Insert and
tighten the #6 screws until the bracket is secured to the wall.
Figure 1. Mount ONT Fiber Tray to Wall
Step 2. Attach Incoming Fiber Cable to Bracket
Refer to Figure 2 and wrap any excess incoming fiber around the ONT
Fiber Tray and Bracket. Leave 4 to 6-inches of fiber cable to connect the
incoming fiber to the ONT.
f
CAUTION!
Do not exceed a minimum bend radius of 2-inches when installing fiber
cabling.
Figure 2. Attach Incoming Fiber Cable to Mounting Bracket
4” to 6”
ADTRAN ONT
424 ONT and 414 RG
Fiber Tray and Wall Mount Bracket
February 2019
61287409F1-13B
P/N: 1287409F1

424 ONT and 414 RG LEDs
Label Status Indication
POWER 

Off
Green
AC or battery off
No Failure
FIBER 

2
Off
Green
Green Flashing
Fast
No connection to the OLT, open
fiber, failure at the ONT, or power
is Off
Signal present and is within oper-
ating range
Ranging in Progress
INTERNET 

Off
Green
No IP address configured on
WAN Interface, or Power is Off
WAN Interface is configured with
IP address
GE 1-4 

2
Off
Green
Green Flashing
Fast
Link is down or not equipped
Link is up
Data is being sent or received
USB 

2
Off
Green
Green Flashing
Fast
Power Off or no device con-
nected
Device connected
Data is being sent or received
2.4GHZ 

2
Off
Green
Green Flashing
Fast
Power is Off, or Wireless 2.4GHz
is Disabled
Wireless 2.4GHz is Enabled
Data is being sent or received on
2.4GHz
PHONE 1-2 

2
Off
Green
Green Flashing
Slow
Unequipped or on-hook and not
ringing
Line is off-hook
Line in ringing state
WPS 

2
Off
Green
Green Flashing
Fast
Power Off or WPS is Disabled
WPS is Enabled
WPS push button pressed,
device is ready to accept connec-
tion
Step 3. Attach ONT to ONT Fiber Tray and Bracket
Refer to Figure 3 and complete the following steps to mount the ONT to
the Bracket.
1. Align the four tabs on the mounting bracket with the four slots on the
back of the ONT.
2. Slide the ONT on to those tabs and secure the ONT by sliding it
slightly to the right until there is an audible “click”.
Figure 3. Attach ONT to ONT Fiber Tray and Bracket
Step 4. Connect Incoming Fiber Cable to ONT
Refer Figure 4 and connect the Incoming Fiber Cable to the Fiber
Connector on the bottom of the ONT.
Figure 4. Connect Incoming Fiber Cable to ONT
Once all cables have been reconnected, refer to the LED table to ensure
the ONT is operating properly.
USB
GE1PHONE 2UPS12V PHONE 1 GE2 GE3 GE4
WPS
RESET
US
GE1PHONE 2UPS12V PHONE 1 GE2 GE3 GE4
WPS
RESET
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2019 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61287409F1-13B*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN 424 2 POTS/4 GigE ONT Job Aid
ADTRAN 414RG 2 POTS/4 GigE Dual Band WiFi Residential Gateway ONT Job Aid