ADTRAN 424RG User manual

Q
uic
k
Start
DESCRIPTION
The 424RG Optical Network Terminal (ONT) Fiber Tray and Wall Mount
Bracket (Fiber Tray and Bracket) is used to mount the ADTRAN 424RG
2 POTS/4 GigE Dual Band WiFi ONT (P/N 1287781F2) to a wall.
The wall mount bracket also incorporates a fiber tray to store excess
incoming fiber should that be required.
Required Tools
The following tools are required when installing the Fiber Tray and
Bracket.
■Power Drill (optional)
■Carpenter’s Level (optional)
■Phillips-head Screwdriver
■Hammer
Installation Steps
To install the Fiber Tray and Bracket, complete the following steps:
1. Select Location and Mount Bracket
2. Attach Incoming Fiber Cable to Fiber Tray and Bracket
3. Connect Incoming Fiber Cable to ONT
4. Attach ONT to Fiber Tray and Bracket
Step 1: Select Location and Mount Bracket
Select a location to mount the Fiber Tray and Bracket near the fiber
entrance. Use the supplied hardware to mount the bracket to the wall as
follows:
gNOTE
Supplied hardware is intended for drywall mounting only. For mounting on
surfaces other than drywall, obtain the appropriate mounting hardware
and follow the provided instructions.
1. Refer to Figure 1 and mark hole locations using the Fiber Tray and
Bracket as a template. Use a carpenter’s level to ensure the bracket
is level.
2. Start anchor into the wall by using a hammer to lightly tap the
anchor in until the threads are close to the wall.
gNOTE
Pre-drill holes using a 1/4” drill bit if difficulty is encountered.
3. Insert either a No. 2 or No. 3 Phillips driver bit into the recess of the
anchor head.
4. Using gentle forward pressure, rotate the wall anchor clockwise until
the collar is flush with the wall.
5. Align theFiber Tray and Bracket with the holes, insert and tighten #6
screws until fixture is tight to the wall.
Figure 1. Mount ONT Fiber Tray to Wall
Step 2. Attach Incoming Fiber to ONT Fiber Tray and
Mounting Bracket
Refer to Figure 2 and wrap any excess incoming fiber around the Fiber
Tray and Bracket.
fCAUTION!
Do not exceed a minimum bend radius of 2-inches when installing fiber
cabling.
Figure 2. Wrap Incoming Fiber Around Fiber Tray and Bracket
Incoming
Fiber
ADTRAN ONT
424RG
Fiber Tray and Wall Mount Bracket
May 2019
61287411F1-13B
P/N: 1287411F1

Once all cables have been connected, refer to the LED table below to
ensure the ONT is operating properly.
424RG LEDs
Label Status Indication
POWER 

Off
Green
AC or battery off
No Failure
FIBER 

2
Off
Green
Green Flashing
Fast
No connection to the OLT, open
fiber, failure at the ONT, or power is
Off
Signal present and is within operat-
ing range
Ranging in Progress
INTERNET 

Off
Green
No IP address configured on WAN
Interface, or Power is Off
WAN Interface is configured with IP
address
GE 1-4 

2
Off
Green
Green Flashing
Fast
Link is down or not equipped
Link is up
Data is being sent or received
USB 

2
Off
Green
Green Flashing
Fast
Power Off or no device connected
Device connected
Data is being sent or received
2.4GHZ 

2
Off
Green
Green Flashing
Fast
Power is Off, or Wireless 2.4GHz is
Disabled
Wireless 2.4GHz is Enabled
Data is being sent or received on
2.4GHz
5GHZ 

2
Off
Green
Green Flashing
Fast
Power is Off, or Wireless 5GHz is
Disabled
Wireless 5GHz is Enabled
Data is being sent or received on
5GHz
PHONE 1-2 

2
Off
Green
Green Flashing
Slow
Unequipped or on-hook and not
ringing
Line is off-hook
Line in ringing state
WPS 

2
Off
Green
Green Flashing
Fast
Power Off or WPS is Disabled
WPS is Enabled
WPS push button pressed, device
is ready to accept connection
Step 3. Connect Incoming Fiber Cable to ONT
Refer to Figure 3 and connect the Fiber Cable to the Fiber Connector on
the bottom of the ONT.
Figure 3. Connect Incoming Fiber to ONT
Step 4. Attach ONT to ONT Fiber Tray and Bracket
1. Refer to Figure 4 and position the ONT as shown. Align the two
mounting tabs on the bottom of the ONT with the two slots on the
Wall Mount Bracket.
2. Gently push the ONT towards the Wall Mounting Bracket until the
ONT snaps onto the bracket.
Figure 4. Attach ONT to ONT Fiber Tray and Bracket
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2019 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61287411F1-13B*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN 424RG 2 POTS/4 GigE Dual Band WiFi Residential Gateway ONT Job Aid