ADTRAN Express 5200 User manual

Express 5200
Frame Relay Service Unit
USER MANUAL
61202175L1-1A
May 1999
1202175L1 Base Unit
1202187L1 Dual FXO Card
1202188L1 Dual FXS Card
1202189L1 Dual E&M Card
1204001L1 4-wire SW56 DBU Card
1204002L1 V.34 DBU Card
1204004L1 ISDN DBU Card
1204006L1 External DCE Card

This product includes software developed by the University of California, Berkeley,
and its contributors.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
© 1999 ADTRAN, Inc.
All rights reserved.
Printed in USA.

61202175L1-1 Express 5200 User Manual iii
ABOUT THIS MANUAL
This manual is arranged so you can quickly and easily find the information
you need. The following is an overview of the contents of this manual:
• Chapter 1, Introduction, familiarizes you with frame relay networks and
Express 5200 highlights. The chapter also gives a brief explanation of
options that may be purchased for use with the Express 5200.
• Chapter 2, Installation, describes the Express 5200 connectors (pin assign-
ments are given in Appendix A) and provides an installation diagram.
• Chapter 3, Operation, explains how to operate your Express 5200 using
either the front panel or a VT 100 terminal interface.
• Chapter 4, Applications, provides examples of some common Express 5200
applications. This chapter includes network diagrams as well as configu-
ration tables for each example.
• Chapter 5, Configuration Overview, explains how to access the
Express 5200 Configuration menu.
• Chapter 6 through 11 provide brief explanations for selections made in
the Configuration menus. These chapters are based on the first level
menu branches of the Configuration menu: DTE Ports, Voice Card
Options, Network Port, Dial Backup, IP Routing, and System configura-
tion.
• Chapter 12, Statistics, describes how to access statistics information from
the Express 5200.
• Chapter 13, Testing, explains how to access the Express 5200 diagnostic
features, including ping and loopback tests.
• Chapter 14, Activating DBU Functions, provides information on the dial-
ing options accessed through the Main menu.
• Appendix A provides pinouts for the Express 5200 connectors.
• Appendix B contains product specifications.
• Appendix C is a list of acronyms and abbreviations used in this docu-
ment.
• Appendix D is a glossary of related terms.

iv Express 5200 User Manual 61202175L1-1
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Whenusingyour telephoneequipment,pleasefollowthesebasicsafetyprecautions
to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as near a bath tub, wash bowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm.
There is a remote risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual.
Do not dispose of batteries in a fire. They may explode. Check with local codes
for special disposal instructions.
Notes provide additional useful information.
Cautions signify information that could prevent service interrup-
tion.
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.

61202175L1-1 Express 5200 User Manual v
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules. On the bottom of the equip-
ment housing is a label showing the FCC registration number and ringer equiva-
lence number (REN) for this equipment. If requested, provide this information to
the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company
may temporarily discontinue service. If possible, advance notification is given;
otherwise, notification is given as soon as possible. The telephone company will
advise the customer of the right to file a complaint with the FCC.
3. The telephone company may make changes in its facilities, equipment, opera-
tions, or procedures that could affect the proper operation of this equipment.
Advance notification and the opportunity to maintain uninterrupted service are
given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair
and warranty information. The telephone company may require this equipment
to be disconnected from the network until the problem is corrected or it is certain
the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone network
or premises wiring using an FCC compatible modular jack, which is Part 68 com-
pliant.
7. The following information may be required when applying to the local telephone
company for a dial-up line for the V.34 modem:
8. In the event of equipment malfunction, all repairs should be performed by
ADTRAN. It is the responsibility of users requiring service to report the need for
service to their distributor or ADTRAN. See the inside back cover of this manual
for information on contacting ADTRAN for service.
Service Type Digital Facil-
ity Interface
Code
Service
Order Code Network Jacks
56 kbps Digital Interface 04DU5-56 6.0F RJ-48S
64 kbps Digital Interface 04DU5-64 6.0F RJ-48S

vi Express 5200 User Manual 61202175L1-1
ADTRAN Year 2000 (Y2K) Readiness Disclosure
ADTRAN has established a Year 2000 program to ensure that our products will cor-
rectly function in the new millennium. ADTRAN warrants that all products meet Year
2000 specifications regardless of model or revision. Information about ADTRAN's
Year 2000 compliance program is available at the following:
Product Matrix: www.adtran.com/y2kfax.html
E-mail: [e-mail]
Faxback Document Line: [phone]
Y2K plans and product certifications are listed in the Product Matrix (see above)
Y2K Project Line: [phone]

61202175L1-1 Express 5200 User Manual vii
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruction man-
ual, may cause harmful interference to radio frequencies. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC
limits.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard enti-
tled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:
“Appareils Numeriques,” NMB-003 edictee par le ministre des Communications.
Changes or modifications to this unit not expressly approved by the par-
ty responsible for compliance could void the user's authority to operate
the equipment.

viii Express 5200 User Manual 61202175L1-1
CANADIAN EQUIPMENT LIMITATIONS
Notice: The Canadian Industry and Science Canada label identifies certified equip-
ment. This certification means that the equipment meets certain telecommunications
network protective, operational, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable methods of connection. In some cases, the com-
pany’s inside wiring associated with a single line individual service may be extended
by means of a certified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above limitations may not prevent degra-
dation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian mainte-
nance facility designated by the supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
The Load Number (LN) assigned to each terminal device denotes the percentage of
the total load to be connected to a telephone loop which is used by the device, to pre-
vent overloading. The termination on a loop may consist of any combination of
devices subject only to the requirement that the total of the Load Numbers of all
devices does not exceed 100.
Users should not attempt to make such connections themselves, but should
contract the appropriate electric inspection authority, or an electrician, as
appropriate.

61202175L1-1 Express 5200 User Manual ix
Table of Contents
Chapter 1. Introduction
Understanding Frame Relay .............................................................................................. 1-1
Product Overview......................................................................................................... 1-2
DDS Operation .............................................................................................................. 1-3
SNMP.............................................................................................................................. 1-3
TELNET..........................................................................................................................1-4
Voice Compression....................................................................................................... 1-4
FXS Module ........................................................................................................... 1-5
FXO Module .......................................................................................................... 1-5
E&M Module ......................................................................................................... 1-5
Dial Backup Operation.................................................................................................1-5
Card Options ................................................................................................................. 1-6
Warranty and Customer Service.................................................................................1-7
Chapter 2. Installation
Unpack, Inspect, Power Up ...............................................................................................2-1
Receiving Inspection..................................................................................................... 2-1
ADTRAN Shipments Include......................................................................................2-1
Customer Provides ....................................................................................................... 2-2
Power Up........................................................................................................................2-2
Rear Panel ............................................................................................................................. 2-2
DBU and Voice Interface Card Slots ..........................................................................2-4
Telco Connector............................................................................................................. 2-4
Control Port ................................................................................................................... 2-4
DTE Connectors ............................................................................................................ 2-4
Chapter 3. Operation
Front Panel ........................................................................................................................... 3-1
LCD Window................................................................................................................. 3-1
Enter................................................................................................................................ 3-1

Table of Contents
x Express 5200 User Manual 61202175L1-1
Up and Down Arrows..................................................................................................3-1
Cancel..............................................................................................................................3-1
Numeric Keypad...........................................................................................................3-2
Next, Prev, Add, Delete................................................................................................3-2
Shift .................................................................................................................................3-2
LED Descriptions ..........................................................................................................3-2
Front Panel Operation..................................................................................................3-3
VT 100 Terminal Connection and Operation............................................................3-4
Express 5200 Menu Structure......................................................................................3-6
Main Menu .............................................................................................................3-7
Chapter 4. Applications
Data Applications ................................................................................................................4-1
SNA/SDLC with Local Spoofing................................................................................4-1
SNA and LAN Application with SNMP/TELNET Management .........................4-4
Bisync Application........................................................................................................4-7
Transparent Application............................................................................................4-10
Voice Applications ............................................................................................................4-12
Switched Mode Application......................................................................................4-12
External Call Origination ...................................................................................4-13
External Call Reception ......................................................................................4-13
Internal Calls ........................................................................................................4-13
Voice Over Frame Relay Application.......................................................................4-14
PLAR Mode Application............................................................................................4-15
Direct Mode Application............................................................................................4-16
Chapter 5. Configuration Overview
Local and Remote Configuration ......................................................................................5-1
Chapter 6. DTE Port Configuration
Port Disabled Protocol (DISABLE).............................................................................6-3
Frame Relay Protocol....................................................................................................6-3
Physical Layer Options (PHYS LYR OPTS) ......................................................6-3
Protocol Options (PROTOCOL OPTS) ..............................................................6-5
Address Table (ADDR TABLE) ..........................................................................6-6
SDLC Protocol ...............................................................................................................6-7
Physical Layer Options (PHYS LYR OPTS) ......................................................6-7
Protocol Options (PROTOCOL OPTS) ..............................................................6-9
Address Table (ADDR TABLE) ........................................................................6-10
Transparent BOP Protocol (TRANS BOP)...............................................................6-11
Physical Layer Options (PHYS LYR OPTS) ....................................................6-12