Advanced Bionics Roger Select User manual

ROGER™ SELECT
QUICK GUIDE
Turn on the Roger Select. Ensure the
appropriate battery to the Roger receiver is
attached to the processor or hearing aid.
Hold Roger Select within 10 cm/4 inches from
the Roger receiver or hearing aid.
Press the “Connect” button on the back
of the Roger Select.
Turn on the Roger Select and phone/computer.
Place next to each other.
Ensure the phone/computer Bluetooth setting is
enabled.
On the phone/computer, choose SEARCH or
SCAN to search for Bluetooth enabled devices or
audio enhancements.
Press the Bluetooth button for 2 seconds until
the blue light fades and then push it again briefly
until it blinks blue.
The phone/computer should present a list of
Bluetooth devices it has detected. Scroll down to
choose “Roger Select” from this list and confirm
the connection is established.
The Roger Select should now be paired to the
phone/computer and the indicator light will stop
blinking.
To add another Bluetooth device, briefly press
until the back indicator light blinks blue again
and repeat steps 2 to 6.
To enter standby mode, briefly press the
on/off button to put Roger Select into
Bluetooth standby mode. This means the
Roger Select microphone is switched off but
incoming calls can still be received.
In Bluetooth standby mode, the battery of the
Roger Select is drained. It is recommended
to switch off the Roger Select completely if
no calls are expected to be made.
Connect Blue Blinking Connecting or
pairing mode
Solid Green Connecting/pairing
successful
Red Double
Blinking
Connect timeout,
move device closer
Red Triple
Long Blinking
Device not
compatible
Bluetooth Blue Slow
Blinking
Bluetooth Standby
Mode
Blue Double
Blinking Incoming Call
Blue Solid Active Call
Blue Fast
Blinking
Network Issue,
please press the
connect button
DEVICE DESCRPITION
Roger Select is a microphone that picks up the voice of a speaker and sends it wirelessly directly into your
hearing devices. You can place Roger Select in the middle of a table e.g. in a restaurants, or it can be
worn by a single person i.e. to hear a distant talker. Follow the steps below to pair the Roger Select.
PAIRING ROGER SELECT TO A
PROCESSOR OR HEARING AID
TIP
The back indicator light will turn green for two
seconds to confirm a successful connection.
You can connect an unlimited number of Roger
receivers to your Roger Select, simply repeat
step 2 and 3 for any other Roger receiver.
1
2
3
STANDBY MODE
PAIR ROGER SELECT WITH YOUR
PHONE / COMPUTER (BLUETOOTH)
1
2
3
4
5
6
7
TIP
The phone/computer may ask to enter a
passcode. If so, enter ‘0000’. Some
phones/computers may ask which Bluetooth
service you want to enable, select Headset audio
device and microphones in parallel.
1
2

Make sure you have switched on the Roger
Select
Plug the rectangular end of the short audio
cable into the Roger Select.
Plug the round end of the short audio cable
into the headphone output of your portable
device.
Start the music or music app on the portable
audio device.
Accepting Incoming Calls -The Roger Select
Bluetooth light indicator will flash blue when
receiving a call. To accept an incoming call, press
the center touch key.
Making Phone Calls -Once you dial on your
phone, you will hear the ring tone in your
processor/hearing aid. It is recommended to wear
your Roger device on your chest during the phone
call or place it on the table in front of you.
Ending a Call -Tap and hold the center touch key
or end the call on your phone.
Rejecting a Call -Tap and hold the center touch
key for 2 seconds until the blue light stops flashing.
You can also reject the call from your phone.
Mute Call -To mute your voice, tap the center
touch key. The red mute indicator light will light up.
Battery
Status
Green Fast
Blinking Charging
Green Solid Fully Charged
Green Slow
Blinking
Switched on, Battery
Full
Orange
Blinking Battery Half Full
Red Blinking Battery Empty,
Charge Roger Select
Microphone
Mode Green all Six
Segments
Microphone in All
Directions
(All-Around Active)
Green One To
Five Segments
Microphone in
Selected
Directions Active
Mute Red Solid Microphone Muted
Red Blinking
Unmute Not
Possible, Another
Roger Select in the
Same Network is
Active
If two or more people are
speaking, you may tap
segments to focus on
specific people.
To hear the whole group
again, tap the center touch
key
ROGER™ SELECT
QUICK GUIDE
PHONE CALLS
LISTENING TO A PORTABLE AUDIO
DEVICE
BATTERY STATUS
TIP
The Roger Select will automatically mute when the
audio cable is plugged in. Activate the microphone
by pressing the center touch key. Now you will
hear the audio device and microphones in parallel.
To end the transmission of the audio signal, unplug
the audio cable or switch the Roger Select off.
1
3
2
4
MICROPHONE MODE
1
2
CAN’T FIND WHAT YOU NEED?
877-829-0026
CONTACT US!
Contact Us