Advantech MIC-3000 Series User manual

Advantech CompactPCI™
Modular Industrial Computer
MIC-3041L

MIC-3041L User Manual --- Page II
Copyright Notice
This document is copyrighted, 2004. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described in
this manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
Acknowledgements
PICMG™, CompactPCI™ and the PICMG™, CompactPCI™ logos are trademarks of
the PCI Industrial Computers Manufacturers Group. All other product names or
trademarks are properties of their respective owners.
CE Notification
The MIC-3041L, developed by Advantech Co., Ltd., has passed the CE test for
environment specifications when shielded cables are used for external wiring. We
recommend the use of shielded cables.

MIC-3041L User Manual --- Page III
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for one year from the date of
purchase.
This warranty does not apply to any products which have been repaired or altered
by persons other than repair personnel authorized by Advantech, or which have
been subject to misuse, abuse, accident or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is
defective, it will be repaired or replaced at no charge during the warranty period. For
out-of-warranty repairs, you will be billed according to the cost of replacement
materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. For example, CPU
speed, Advantech products used, other hardware and software used, etc. Note
anything abnormal and list any on-screen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt) in
a shippable container. A product returned without proof of the purchase date is not
eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to
your dealer.

MIC-3041L User Manual --- Page IV
Packing List
Before installation, ensure that the following materials have been received:
• One MIC-3041L CompactPCI™ enclosure with backplane
• One box of accessories
• One warranty certificate
• One CD-ROM for user manual (PDF file)
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3041L or any other Advantech
products, please visit our support website at:
• http://www.advantech.com.tw/support
For more information about Advantech's products and sales information, please
visit:
• http://www.advantech.com.

MIC-3041L User Manual --- Page V
Contents
1. General Information............................................ 1
1.1 Introduction ................................................................................. 2
1.2 Features ....................................................................................... 3
1.3 Specifications................................................................................. 3
1.3.1 General.......................................................................................... 3
1.3.2 Hot-swap Fans................................................................................. 3
1.3.3 Power Supply................................................................................... 3
1.4 Dimensions.................................................................................4
2. Installation………............................................... 6
2.1 Initial Inspection............................................................................. 7
2.2 The MIC-3041L Illustration ............................................................... 7
2.3 Installation Procedures ................................................................... 8
2.3.1 Card Installation and Removal........................................................... 8
2.3.2 Before Operating the System………......................................................9
2.3.3 Installing a 3.5” Hard Disk Drive......................................................10
2.3.4 Connecting with rear I/O module....................................................... 10
2.3.5 Configuring the build-in IDE by RIO module......................................... 10
2.3.6 Replacing the Hot-swap Fan and Air Filter........................................ 11
3. Backplane………….................................................. 12
3.1 General Information......................................................................13
3.2 Features......................................................................................13
3.3 Specification.................................................................................13
3.4 Slot Assignments……......................................................................13
3.5 Connector and jumper locations.......................................................15
3.5.1 ATX Power Connector (ATX1) .....................................................16
3.5.2 Power Switch .................................................................16
3.5.3 V I/O Voltage Selection ...............................................16
3.5.4 Fan Module Connector .................................................17
3.5.5 LED Board Connector ....................................................17
3.6 Clock Routing Configuration............................................................17
Appendix A ………………………………………………………………………18
Appendix B ……………………………………………………………………… 34

MIC-3041L User Manual --- Page VI
Figures
Figure 1-1: MIC-3041L dimensions ........................................................................4
Figure 1-2: Appearance of MIC-3041L......................................................................... 5
Figure 2-1: Front view of MIC-3041L ....................................................................7
Figure 2-2: Removable parts of MIC-3041L ................................................................8
Figure 2-3: Installing a card into the chassis.....................................................9
Figure 2-4: 3.5” Hard Disk Drive and cable location ........................................................10
Figure 2-5: Hot swappable fan maintenance ........................................................11
Figure 3-1: MIC-3803/MIC-3805 Backplane slot numbering ....................................... 15
Figure 3-2: MIC-3803/MIC-3805 connector and jumper locations on the rear side 16
Figure 3-3: V I/O voltage selection...................................................................... 17

MIC-3041L User Manual --- Page 1
1
General Information

MIC-3041L User Manual --- Page 2
1.1 Introduction
MIC-3041L is an ideal entry level CompactPCI platform. It is designed as a cost
effective 4U high enclosure with a 6U CompactPCI H.110 CT bus or non-CT bus
backplane. It is suitable for telecommunication, computer telephony integration,
and industrial automation. The built-in high quality backplane with 64 bit / 66MHz
bus speed offers best impedance control, meets open architecture standards and is
compatible with all Advantech CompactPCI boards.
The MIC-3041L supports build-in on-board IDE, floppy and USB connectors for
cost-effective solution. The MIC-3041L-TA supports IEEE 1101.11 rear I/O transition
board, but not for MIC-3041L-CA. Users can route I/O signals to the rear transition
board to simplify system cabling. Front boards pop in and out without any
hardwiring. Efficient hot swappable fan module gives easy self-maintenance
capability. The system slots can support CPU boards featuring desktop Intel®
Pentium®IV processors up to 2.2GHz (MIC-3358) or Intel®Pentium®M processors
up to 1.8GHz (MIC-3369). With the chassis management module (968A390021,
also call MIC-3924L-A), the chassis temperature and fan speed can be detected. A
1U space is reserved for two IDE drive bays on top of the chassis, and the built-in
slim line CD-ROM and floppy drive provides storage media needs.
To achieve the most cost effective combination for entry-level CT applications or
entry to middle-end industrial applications, one can have a MIC-3041L enclosure
with a MIC-3358 6U CPCI board and Intel Pentium IV processor without any rear I/O
transition board. This gives the best performance and price balance and makes the
MIC 3041L the most cost effective solution.
There are two kinds of MIC-3041L:
zMIC-3041L-TA: MIC-3041L enclosure, w/ 4-slot CompactPCI™ 6U backplane
(MIC-3805) supporting non-CT bus application.
zMIC-3041L-CA: MIC-3041L enclosure, w/ 4-slot CompactPCI™ 6U backplane
(MIC-3803) supporting CT bus application.
zPlease contact your local distributor for MIC-3041L-CA, not for
standard ordering process.

MIC-3041L User Manual --- Page 3
1.2 Features
zFour 6U card slots
zSupports front and rear I/O
zSupports H.110 CT application or non-CT application
zTwo IDE storage devices
z300W ATX power supply with PFC
zHot-swap compliant backplane
zA hot-swap fan module
zIntegrated intelligent management module, 968A390021 (also call
MIC-3924L-A), which can detect the chassis temperature and fan speed.
1.3 Specifications
1.3.1 General
zConstruction: Aluminum frame and galvanized sheet steel
z6-slot space (24 TE), including one system slot and three peripheral slots
z"Hot swappable” platform complies with PICMG 2.1 R 2.0 Hot Swap
Specification
zDimensions (W x H x D, mounting flanges not included):
4U: 440 x 177 x 300 mm (17.3" x 7" x 11.8")
zWeight: 11.2 kg (24.7 lb)
zOperating temperature: 0 ~ 45° C
zStorage temperature: -20° C ~ 60° C
zRelative humidity: 10 ~ 95% @ 40° C, non-condensing
zOperating altitude: 0 ~ 3,048 meters (0 ~ 10,000 feet)
zStorage/transit altitude: 0 ~ 12,190 meters (40,000 feet)
zShock: 10 G (operating); 30 G (storage/transit)
zRandom vibration: 1.0 Grms (operating)
1.3.2 Hot-swap Fans
zAir flow: One 163-CFM fan (outlet)
zPower consumption: 0.45 A @ 12 V, 0.09 A @ 12V
zRated fan speed: 2170/4500 rpm
zLife expectancy: 50,000 hours @ 25° C

MIC-3041L User Manual --- Page 4
1.3.3 Power Supply
zInput: 100~240 V AC @ 50~60 Hz with auto switching capability -- PFC (Power
Factor Correction).
zOutput (per module):300W, +3.3V,+5V,+12V total output power shall not
exceed 280W
zMaximum load: +3.3V @ 28A, +5V @ 30A, +12V @ 15A, -5V @0.3A, -12V @
0.8A, +5Vsb @ 2.0 A
zMinimum load: +3.3 V @ 0.3 A, + 5V @0.1 A, +12 V @ 0 A, -12V @0A
zMTBF: 100,000 hours @ 25° C
zSafety: UL/CE
1.4 Dimensions
Figure 1-1: MIC-3041L dimensions.

MIC-3041L User Manual --- Page 5
Figure 1-2: Appearance of MIC-3041L

MIC-3041L User Manual --- Page 6
2
Installation

MIC-3041L User Manual --- Page 7
2.1 Initial Inspection
We have carefully inspected the MIC-3041LL mechanically and electrically before
shipping. It should be free of marks and scratches and in perfect working order upon
receipt. As you unpack the MIC-3041L, check it for signs of shipping damage
(damaged box, scratches, dents, etc.). If it is damaged or fails to meet
specifications, notify our service department or your local representative
immediately. Also notify the carrier. Retain the shipping carton and packing
material for inspection by the carrier. After inspection, we will make arrangements
to repair or replace the unit.
Warning! We strongly recommend that only qualified, experienced personnel
install or remove components. They must exercise extreme caution when doing so.
2.2 The MIC-3041L Illustration
The MIC-3041L is designed to be installed and maintained easily.
Figure 2-1 and Figure 2-2 illustrate important components on the front and hot
swappable parts of the enclosure.
Figure 2-1: Front view of MIC-3041L

MIC-3041L User Manual --- Page 8
Figure 2-2: Removable parts of MIC-3041L
2.3 Installation Procedures
2.3.1 Card Installation and Removal
The CompactPCI™ connectors are firm and rigid, and require careful handling while
plugging and unplugging. Improper installation of a card can easily damage the
backplane of the chassis.
The system card can be installed only in the system slot. Do not insert the system
card into any other slot, or insert a peripheral card into the system slot. The system
slot is marked by a triangle enclosing the slot number 5. Please refer to chapter 3.
The insert/eject handles on CompactPCI™ cards help users to install and remove
the cards easily and safely. Follow the procedures below to install a card into a
chassis:
To install a card:
1. Hold the card horizontally. Be sure that the card is oriented correctly.
The components of the card should be pointing to the up side.
2. Be sure that the handles of the card are not latched. Release the handles if they
are latched. Handles from different vendors may have different latch designs.
Caution: Keep your fingers away from the latch hinges to prevent your
fingers from getting pinched.
3. Insert the card into the chassis by sliding the left and right edges of the card into
the card guides.

MIC-3041L User Manual --- Page 9
4. Push the card into the slot gently by sliding the card along the card guide until
the handles meet the rectangular holes of the cross rails. Please refer to figure
2-3.
Figure 2-3: Installing a card into the chassis
Note: If the card is correctly positioned and has been slid all the way into
the chassis, the handles should match the rectangular holes. If not,
remove the card from the card guide and repeat step 3 again. Do not try to
install a card by forcing it into the chassis.
5. Pull the right handle to the left and pull the left handle to the right to push the
card into place and fixed.
6. Secure the card by locking the handles into place.
To remove a card:
1. Unscrew the screws on the card front panel. Release the locking latches on the
handles.
2. To push the red buttons on the right and left handles to loosen the card from the
backplane.
3. Slide the card out.
2.3.2 Before Operating the System
Before operating your system, check your power supply source firstly.
Two mounting flanges are included for users who would like to install the MIC-3041L
on a 19" rack.

MIC-3041L User Manual --- Page 10
2.3.3 Installing a 3.5” Hard Disk Drive
Follow the procedures to install 3.5" hard disk drives in the MIC-3041L:
1. Remove the top plate.
2. Mount the HDD on the HDD rack with screws.
3. Connect the IDE cable to the HDD.
4. Power on and check the HDD can be found during initializing.
Figure 2-4: 3.5” Hard Disk Drive and cable location
2.3.4 Connecting with rear I/O module
The MIC-3041L is limited to be used with rear I/O module. Please refer to appendix
B for the details. To install the RIO module, please follow the steps below:
1. Remove the blank panel above the system RIO slot. (Suggest to remove all the
blank panels for installation)
2. User can find there is one IDE cable with two IDE connectors (40 pins ) inside.
3. Connecting with the right connector on board, and slide into the card cage.
4. Power up the system and check all the storage devices work properly.
2.3.5 Configuring the build-in IDE by RIO module
MIC-3803 and MIC-3805 have build-in onboard IDE connectors. No IDE adapter is
needed. Please note, not all of the RIO has two channels to support 2x IDE and
CDROM at same time because of hardware limitation. Please consult your sales for
a suitable configuration.

MIC-3041L User Manual --- Page 11
Note: (1) RIO-3309C/RIO-3309L only has one IDE channel, thus the IDE CD-ROM
is connected to “USB to IDE” daughter board.
(2) Please use Windows 2000 SP4 for USB driver installation. If neither CPU
board nor RIO have PS/2 port, please use Com port mouse with USB
keyboard to copy USB 2.0 driver to floppy or HDD for USB 2.0 driver
installation.
2.3.6 Replacing the Hot-swap Fan and Air Filter
The MIC-3041L provides one hot-swap fans at the left hand sides of the MIC-3041L.
Please refer to Figure 2-5. It can be removed without turning off the system power
or interrupting system operation.
Follow these steps to replace a fan:
1. Unfasten the fan's holder.
2. Slide the fan's holder out.
3. Replace the old fan with a new one.
4. Slide the fan's holder in.
5. Fasten the new fan's holder.
Figure 2-5: Hot swappable fan maintenance
The air filter may become dirty after a period of time. Follow these steps to replace
a filter:
1. Remove the top plate.
2. Replace the dirty filter with a clean one.
3. Reattach the top plate.
Repeat steps 1 to 3 to replace other filters.

MIC-3041L User Manual --- Page 12
3
Backplane

MIC-3041L User Manual --- Page 13
3.1 General Information
There are two kinds of backplanes for MIC-3041L series. MIC-3803 is backplane
with H.110 CT bus, and MIC-3805 is backplane without H.110 CT bus. Both
backplanes provide four CompactPCI™ slots. One slot is assigned to the CPU board
and the other slots for three peripheral boards. The MIC-3041L supports onboard
IDE, floppy and USB connecters, providing cost effective solution. The backplane
also provides several 3-pin connectors to connect hot-swappable cooling fan
module. In order to provide users with a flexible system configuration, the
MIC-3041L includes one standard ATX power connector to accept one ATX power
supply. The MIC-3041L complies with PICMG 2.1 Hot-Swap Specification, providing
full hot-swapping capability. Users can build a hot-swap system using hot-swap
plug-in boards and software.
3.2 Features
zFour CompactPCI™ slots (one system slot and three peripheral slots)
z64-bit PCI bus compliant
zComplies with PICMG 2.1 Hot-Swap Specification
zAccepts redundant ATX power supply
zChassis alarm module for environment monitoring.
zHot-swappable fan interface.
3.3 Specification
zFour CompactPCI™ slots (one system slot and three peripheral slots)
zBus width: 64-bit
z8-layer PCB, 3.0 mm thick
zPower connector: One ATX power connector for connecting standard ATX power
supply
zComplies with CompactPCI™ Specification PICMG 2.0, R.3.0
zComplies with CompactPCI™ Hot Swap Specification PICMG 2.1, R2.0.
zComplies with CompactPCI™ Computer Telephony PICMG2.5, R1.0 (optional)
zDimensions: 146 x 255.85 mm
3.4 Slot Assignments
The CompactPCI™ specification defines slot numbering separation for physical and
logical slots. Each slot has a physical number and a logical number (refer to the
CompactPCI™ specification version 2.0 R3.0 for further information on slot
assignments). The physical numbers are printed on the backplane, enclosed in

MIC-3041L User Manual --- Page 14
circles or triangles. Slot5 of MIC-3803 and MIC-3805 marked by a triangle, is the
system slot and can only be used by a CPU board. The other slots are peripheral
slots. The logical number of each slot is defined according to the IDSEL signal and
the associated address used to select the slot. Table 3-1 shows the system slot and
peripheral slots relationships on the backplane. The system slot has a logical
number of 1, and the peripheral slot has a logical number of 2~4. The connectors in
logical slot 1 are designated as 1-P1, 1-P2, 1-P3, 1-P4, 1-P5 from the bottom up.
Nomenclature for connectors in the other slot is similar, such as 2-P1 and 2-P2.
Connector P1 on the system slot is a keyed connector providing 32-bit
CompactPCI™ bus between the system slot and the peripheral slot. Connector P2 on
the system slot is an un-keyed connector providing 64-bit CompactPCI™ bus
between the system slot and the peripheral slots.
Please check appendix A for the pin assignment for all the connectors on the
backplane.
Table 3-1 : MIC-3803 & MIC-3805 System to peripheral slot signal assignment
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 2)
CLK0 P1:D6 CLK P1:D6
AD31 P1:E6 IDSEL P1:B9
REQ0# P1:A6 REQ# P1:A6
GNT0# P1:E5 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 3)
CLK1 P2:A1 CLK P1:D6
AD30 P1:A7 IDSEL P1:B9
REQ1# P2:C1 REQ# P1:A6
GNT1# P2:D1 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 4)
CLK2 P2:A2 CLK P1:D6
AD29 P1:B7 IDSEL P1:B9
REQ2# P2:E2 REQ# P1:A6
GNT2# P2:D2 GNT# P1:E5
System Slot (Logical Slot 1) Peripheral Slot (Logical Slot 5)
CLK3 P2:B2 CLK P1:D6
AD28 P1:C7 IDSEL P1:B9
REQ3# P2:E2 REQ# P1:A6
GNT3# P2:C3 GNT# P1:E5