Advantech MIC-3039 User manual

MIC-3039
1U high 2-slot CompactPCITM enclosure
with rear I/O support

Preface and Table of Contents
PartNo.2002303900 1st Edition
Printed in Taiwan August 2001
Copyright Notice
This document is copyrighted, 2001. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from its
use.
Acknowledgements
PICMG™,CompactPCI™ andthe PICMG™,CompactPCI™ logosare
trademarks of the PCI Industrial Computers Manufacturers Group
All other product names or trademarks are properties of their
respective owners.
CE Notification
The MIC-3039, developed by Advantech Co., Ltd., has passed the CE
test for environment specifications when shielded cables are used for
external wiring. We recommend the use of shielded cables.

MIC-3039 User's Manual

Preface and Table of Contents
Product warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for
one year from the date of purchase.
This warranty does not apply to any products which have been
repaired or altered by persons other than repair personnel authorized
by Advantech, or which have been subject to misuse, abuse, accident
or improper installation. Advantech assumes no liability under the
terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If
an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service
time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. For
example, CPU speed, Advantech products used, other hardware
and software used, etc. Note anything abnormal and list any on-
screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your
manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandise authorization) number from your dealer. This allows us
to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

MIC-3039 User's Manual
Packing List
Before installation, ensure that the following materials have been
received:
•OneMIC-3039CompactPCI™ enclosure with two-slotbackplane
•One box of accessories, including, a pair of rackmount brackets, four
rubber stands, as well as several screws.
•One warranty certificate
•This user's manual
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3039 or any other
Advantech products, please visit our support website at:
•http://www.advantech.com.tw/support
For more information about Advantech's products and sales informa-
tion, please visit:
•http://www.advantech.com

Preface and Table of Contents
Contents
1. General Information ..................................... 1
1.1 Introduction .................................................................................2
1.2 Features .......................................................................................2
1.3 Specifications ..............................................................................3
1.3.1 General.........................................................................................3
1.3.2 Fans .............................................................................................3
1.3.3 Power Supply..............................................................................4
1.4 Dimensions..................................................................................5
1.5 OrderingInformation..................................................................5
2. Installation ..................................................... 7
2.1 InitialInspection..........................................................................8
2.2 TheMIC-3039Illustration..........................................................9
2.3 InstallationProcedures .............................................................10
2.3.1 Card Installation and Removal...................................................10
2.3.2 Before Operating the System ....................................................12
3. Blackplane................................................... 13
3.1 GeneralInformation ..................................................................14
3.2 Features .....................................................................................14
3.3 Specification ..............................................................................15
3.4 Slot Assignments ......................................................................16
3.5 ConnectorandJumperLocations .............................................18
3.5.1 ATX Power Connector (ATX1)................................................19
3.5.2 Alarm Board Interface (CN1) ....................................................19
3.5.3 Power Switch (PS1)...................................................................19
3.5.4 V I/O Voltage Selection (JP2).....................................................19
3.5.5 Screw Terminal for External Power Supply ..............................20
3.6 ClockRoutingConfiguration ...................................................20

MIC-3039 User's Manual
A. Pin Assignments........................................21
A.1 SystemSlotP1 Connector ........................................................22
A.2 SystemSlotP2 Connector ........................................................23
A.3 SystemSlotP3 Connector ........................................................24
A.4 SystemSlotP4 Connector ........................................................25
A.5 SystemSlotP5 Connector ........................................................26
A.6 PeripheralSlotP1Connector...................................................27
A.7 PeripheralSlotP2Connector...................................................28
A.8 PeripheralSlotP3Connnector.................................................29
A.9 PeripheralSlotP4Connector...................................................30
A.10PeripheralSlotP5 Connector...................................................31
A.11 ATXPowerConnector(ATX1)..................................................32
A.12AlarmBoardInterfaceConnector(CN3)..................................33
A.13FanModuleConnectors(FAN1~4) ...........................................34
A.14PowerSwitchConnector(JP2) .................................................34

Preface and Table of Contents
Figures
Figure 1-1: MIC-3039 dimensions ................................................................ 5
Figure 2-1: Front view of MIC-3039 ............................................................... 9
Figure 2-2: Rear view of MIC-3039 ................................................................ 9
Figure 2-3: Installing a card into the chassis.............................................. 11
Figure 3-1: Slot numbering of the backplane.............................................. 17
Figure 3-2: The connector and jumper locations on the front side ............ 18
Figure 3-3: The connector and jumper locations on the rear side ............. 18

MIC-3039 User's Manual
Tables
Table 3-1: System to peripheral slot signal assignment .......................... 16
Table 3-2: Backplane's connector and jumper description ...................... 18
Table 3-3: V I/O voltage selection ............................................................... 19
Table A-1: System slot P1 connector ......................................................... 21
Table A-2: System slot P2 connector ......................................................... 23
Table A-3: System slot P3 connector ......................................................... 24
Table A-4: System slot P4 connector ......................................................... 25
Table A-5: System slot P5 connector ......................................................... 26
Table A-6: Peripheral slot P1 connector .................................................... 27
Table A-7: Peripheral slot P2 connector .................................................... 28
Table A-8: Peripheral slot P3 connector .................................................... 29
Table A-9: Peripheral slot P4 connector .................................................... 30
Table A-10: Peripheral slot P5 connector .................................................... 31
Table A-11: ATX Power Connector ............................................................... 32
Table A-12: Alarm Board Interface Connector ............................................. 33
Table A-13: Fan Module Connectors ........................................................... 34
Table A-14: Power Switch Connector .......................................................... 34

Chapter 1 General Information 1
1
General Information
CHAPTER

2MIC-3039 User's Manual
1.1 Introduction
The MIC-3039 is Advantech's latest CompactPCI™ enclosure with the
most compact mechanical design of only 1U height. With the 6U-sized
2-slot backplane, the MIC-3039 supports one single-slot CPU board
(such as Advantech's MIC-3357 or MIC-3377/M) and one single-slot
peripheral board, or one two-slot CPU board merely.
The MIC-3039 supports IEEE 1101.11 rear I/O transition boards. Users
can route I/O signals to the rear transition boards for simplified system
cabling. Front boards pop in and out without the need to do any
hardwiring.
1.2 Features
•The most compact 1U-high enclosure
•Supports two 6U-sized CompactPCI™ slots (one system slot and
one peripheral slot)
•Supports rear I/O
•200 W ATX power supply
•Optional intelligent fault detection and alarm module

Chapter 1 General Information 3
1.3 Specifications
1.3.1 General
•Construction:Aluminum frame and galvanized sheet steel
•2-slot space (8 TE), including one system slot and one peripleral slot
•"Hotswappable”platform complies with PICMG2.1R 1.0 Hot Swap
Specification
•Dimensions(W x H x D, mounting flanges not included):
440x44x280mm(17.3"x1.7"x11.0")
•Weight:4.5 kg(10.0 lb)
•Operatingtemperature:0~50° C(32~ 122°F)
•Storagetemperature:-20°C~ 60°C(-4~158° F)
•Relativehumidity:10 ~ 95%@ 40° C,non-condensing
•Operatingaltitude: 0~3,048meters(0 ~10,000 feet)
•Storage/transitaltitude: 0~ 12,190meters (40,000feet)
•Shock: 10 G (operating); 30 G (storage/transit)
•Randomvibration:1.0Grms(operating)
1.3.2 Fans
•Airflow:Three10.5-CFMcooling fans(flow in),one10.5-CFM
cooling fan (flow out)
•Powerconsumption:0.10A@ 12V
•Ratedfanspeed:7,800rpm
•Lifeexpectancy: 50,000hours@25°C

4MIC-3039 User's Manual
1.3.3 Power Supply
•Input:100~240VAC @50~60Hz,switchable
•PFC (Power Factor Correction) can reach the furget of 95% @ 115 V,
fullload,following the standardof IEC 1000-3-2
•Output:+3.3V @14A,+5V @16 A,+12V@9 A,-12 V@0.7A
•Minumumload:+3.3V@1.0A,+5V@2A,+12V@1.0A
•Maxoutput:185Wfor+5V,+3.3Vand+12V,110Wfor+5Vand+3.3V
•MTBF:100,000 hours@70%load
•Safety:UL/CUL/CE/FCC

Chapter 1 General Information 5
1.4 Dimensions
Figure 1-1: MIC-3039 dimensions
1.5 Ordering Information
•MIC-3039:1U-high CompactPCITM enclosure with 2- slot backplane,
cooling fans and power supply.
•MIC-3377/M:Single-slot 6U CompactPCITM Pentium® III processor
board with VGA and dual LANs
•MIC-3357:Single-slot 6U CompactPCITM Pentium® MMX processor
board with VGA and triple LANs
•RIO-3302:Single-slot 6U CompactPCITM rear transition board with
VGA,2xLAN,1xUSB,2xCOM,1xCompactFlash,1xFDD,2x
IDE, keyboard and mouse connectors

6MIC-3039 User's Manual

Chapter 2 Installation 7
2
Installation
CHAPTER

8MIC-3039 User's Manual
2.1 Initial Inspection
We have carefully inspected the MIC-3039 mechanically and electrical-
ly before shipping. It should be free of marks and scratches and in
perfect working order upon receipt.
As you unpack the MIC-3039, check it for signs of shipping damage
(damaged box, scratches, dents, etc.). If it is damaged or fails to meet
specifications, notify our service department or your local representa-
tive immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.
Warning! We strongly recommend that only qualified, experi-
enced personnel install or remove components. They
must exercise extreme caution when doing so.

Chapter 2 Installation 9
2.2 The MIC-3039 Illustration
The MIC-3039 is designed to be installed and maintained easily.
Figure 2-1 and Figure 2-2 illustrate important components on the front
and rear side of the enclosure.
Figure 2-2: Rear view of MIC-3039
Figure 2-1: Front view of MIC-3039

10 MIC-3039 User's Manual
2.3 Installation Procedures
2.3.1 Card Installation and Removal
The CompactPCITM connectors are firm and rigid, and require careful
handling while plugging and unplugging. Improper installation of a
card can easily damage the backplane of the chassis.
The system card can be installed only in the system slot. The
CompactPCITM specification allows the system slot to be in any
position in the backplane. Do not insert the system card into the other
slot, or insert a peripheral card into the system slot. The system slot is
marked by a triangle enclosing the slot number. Please refer to the
backplane user's manual.
Note: Another easy way to distinguish the system slot is
that the system slot uses red guide rails while the
peripheral slots use gray ones.
The insert/eject handles on CompactPCITM cards help users to install
and remove the cards easily and safely. Follow the procedures below
to install a card into a chassis:
To install a card:
1. Hold the card horizontally. Be sure that the card is oriented
correctly. The components of the card should be pointing to the
upper side.
2. Be sure that the handles of the card are not latched. Release the
handles if they are latched. Handles from different vendors may
have different latch designs.
Caution: Keep your fingers away from the latch hinges to
prevent your fingers from getting pinched.
3. Insert the card into the chassis by sliding the both edges of the
card into the card guides.
4. Push the card into the slot gently by sliding the card along the card
guide rails until the handles meet the rectangular holes of the
handle locker rails.

Chapter 2 Installation 11
Figure 2-3: Installing a card into the chassis
Note: If the card is correctly positioned and has been slid
all the way into the chassis, the handles should
match the rectangular holes. If not, remove the card
from the card guide and repeat step 3 again. Do not
try to install a card by forcing it into the chassis.
5. Left-pull the right handle and right-pull the left handle to push the
card into place.
6. Screw the card if necessary