Advantech MIC-3038 Series Installation and operation manual

1 MIC-3038 Startup Manual



























MIC-3038 Series
4U high 8-slot CompactPCI™ Enclosure
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
• One MIC-3038 CompactPCI™ enclosure with eight-slot
backplane
• One pair of rackmount bracket, and several screws
• One warranty certificate
• One startup Manual
• One CD disc and manual (in PDF format)
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
General
• Construction: Aluminum alloy and Nickel Plated
• Slots: Eight 4HP 6U CompactPCI™ slots (1x system
slot and 7x peripheral slots) Eight 80mm rear transition
slots IEEE 1101.11 compatible
• Hot swappable: Complies with PICMG 2.1 R 2.0 Hot
Swap Specification
• Dimensions (W x H x D, mounting flanges not
included): 441 x 177 x 342 mm (17.3" x 7" x 13.5")
• Weight: 13kg (28.6 lb)
• Operating temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage temperature: -20° C ~ 80° C (-4 ~ 176° F)
• Relative humidity: 10 ~ 95% @40° C, non-condensing
• Operating altitude: 0 ~ 3,048 meters (0 ~ 10,000 feet)
• Storage/transit altitude: 0 ~ 12,190 meters (40,000
feet)
• Shock: 10 G (operating); 30 G (storage/transit)
• Random vibration: 5 ~ 500 MHz 1.0 Grms (operating)
2.0 Grms (Non-operating)
For more information on the MIC-3038 and other Advan-
tech products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our support
website at:
http://support.advantech.com
This manual is for the MIC-3038 series Rev. A1.
Part No. 2002303810 1st. Edition
Printed in Taiwan October 2002
Fans
• Air flow: One 163-CFM fan (side), and one 43-CFM fan
(rear)
• Power consumption: 0.45 A @12 V, 0.09 A @ 12V
• Rated fan speed: 2,170 (side) /4,500 (rear) rpm
• Life expectancy: 50,000 hours @ 25° C
Power Supply
• Total Power: Redundant 300W ATX with PFC
• Input: 100~240 V AC @ 50~60 Hz, auto switchable
• Output: +3.3 V @ 20 A, +5 V @ 32 A, +12 V @ 16 A, -
12 V @ 0.8 A
• Minimum load: +3.3 V @ 1.0 A, + 5V @ 3 A, +12 V @
2.0 A
• Max output: 280 W for +5V, +3.3 V and +12 V, 35A for
+5 V and +3.3 V
• MTBF: 100,000 hours @ 70% load
• Safety: UL/CUL/CE/FCC
We have carefully inspected the MIC-3038 before ship-
ping. It should be free of marks and scratches, and in per-
fect working order upon receipt. As you unpack the MIC-
3038, check for signs of shipping damages (damaged
box, scratches, dents, etc.). If it is damaged or fails to
meet specifications, notify our service department or your
local representative immediately. Also notify the carrier.
Retain the shipping carton and packing material for
inspection by the carrier. We will make arrangements to
repair or replace the unit upon inspection, .
Warning! We strongly recommend that only qualified,
experienced personnel install or remove compo-
nents. They must exercise extreme caution
when doing the MIC-3038 illustration. The MIC-
3038 is designed to be installed and maintained
easily.Figure-1andFigure-2illustrateimportant
components on the front and rear side of the
enclosure
Before Operating the System
Before operating your system, first check your power sup-
ply source. The power supply module included in the MIC-
3038 chassis accepts a full input range of 100~240 V AC
without any switch setting. Two mounting flanges are
included for users who would like to install the MIC-3038
on a 19" rack.
Packing List
Specifications
Initial Inspection
MIC-3038 Series 4U high 8-slot CompactPCI™ Enclosure

2 MIC-3038 Startup Manual
Installing Peripherals
The MIC-3038 accepts MIC-3960 as media interface,
which can adopt 2.5" devices, Compact Flash, slim-type
CD-ROM drive or slim-type FDD drive. Please see table-1
below for MIC-3960 for the device combinations. Mean-
while, MIC-3960 can only be used on MIC-3038B/4-2R
which has a dedicate slot for media blade.
Installing a 3.5" Hard Disk Drive
Follow the procedures below to install 2.5" hard disk
drives in the MIC-3960:
1. Have the HDD isolation pad attached to stick on the
HDD circuit side.
2. Slide HDD into the IDE connector.
3. Fix HDD by screws on the rear of MIC-3038
Installing a Slim-type Floppy Disk and Slim-
type CD-ROM Drives
The MIC-3960 supports up to four IDE devices on the two
IDE channels including IDE CD-ROM drives. But user only
can have up to three IDE devices (including Compact
Flash) due to its space limitation. To install an IDE slim
type CDROM drive with the MIC-3960 you'll need:
• IDE CD-ROM drive / FDD drive (slim type)
• Mounting bracket for slim type CDROM / FDD drive
• Several screws for bracket
The MIC-3960 does not supply a power cable to run a CD
ROMdrive or other desktop style IDE device cause the
power is provided via the connectors. Steps for installing
an IDE CD-ROMdrive / FDD drive with the MIC-3960 are
as follows:
1. Turn the power off to the card cage and remove the
MIC-3960.
2. Mounting the IDE CD-ROM / FDD drive with bracket
and screws on MIC-3960
3. Re-insert the MIC-3960 into the card cage.
4. Power up the system and check if CD-ROM/ FDD drive
can be found.
• MIC-3038A/4-2R: 2U-high CompactPCI?enclosurewith
4-slot backplane (one master slot / three peripheral
slots), hot-swap cooling fans, redundant power supply.
• MIC-3038B/4-2R: 2U-high CompactPCI?enclosurewith
4-slot backplane (one master slot / three peripheral
slots included one media blade slot), cooling fans,
power supply.
• MIC-3960-A: Single-slot 6U CompactPCI? Media car-
rier board.
• MIC-3924A-A: Intelligent Chassis Management Module
Table: MIC-3038 recommended device bay
configuration.
2.5" HDD Slim
CD-ROM
Slim FDD Compact
Flash
Type A 1 1 - 1
Type B 1- 11
Type C 2 - - 1
Ordering Information