Advantech ECU-P1524SPE Installation and operation manual

ECU-P1524SPE Startup Manual 1
Before installation, please make sure that you have received
the following:
• ECU-P1524SPE card
• Quick Start User Manual
If anything is missing or damaged, contact your distributor
or sales representative immediately.
For more detailed information on this product, please refer
to the ECU-P1524SPE User Manual on the Website (PDF
format).
FCC Class A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio com-
munications. Operation of this equipment in a residential
area is likely to cause interference in which case the user is
required to correct interference at his own expense.
CE
This product has passed the CE test for environmental
specifications when shielded cables are used for external
wiring. We recommend the use of shielded cables. This kind
of cable is available from Advantech. Please contact your
local supplier for ordering information.
ECU-P1524SPE
2-port SFP Base Ethernet Card with HSR/PRP
Startup Manual
The ECU-P1524SPE is a standard PCIE extension card
with HSR/PRP functions to reduce data transfer packet loss
probability and ensure seamless switching.
• The ECU-P1524SPE supports following specifications:
• 2 port SFP Base Ethernet Card with HSR/PRP
• Supports HSR Protocol (IEC 62439-3 Clause 5)
• Supports PRP Protocol (IEC 62439-3 Clause 4)
• BUS Type: PCI-Express V1.0
• Dimensions: 175 mm x 100 mm (6.9” x 3.9”)
• Power Consumption: 5V ±5% @ 1000mA typical;
3.3V ±5% @ 600mA typical;
• Operating Temp: -25 ~ 70°C (-3 ~158°F)
• Operating Humidity: 10 ~ 90% RH non-condensing (refer
to IEC 60068-2-3)
After the device driver is installed, you can now install the
ECU-P1524SPE card in your computer.
Please follow the steps below to install the ECU-P1524SPE
card:
1. Turn off your computer and unplug the power cord and
cables. TURN OFF your computer before installing or
removing any components on the computer.
2. Remove the cover of your computer.
3. Remove the slot cover on the back panel of your
computer.
4. Touch the metal part on the surface of your computer
to neutralize the static electricity that might be on your
body.
5. Insert the ECU-P1524SPE card into a PCI Express
slot. Hold the card only by its edges and carefully align
it with the slot. Insert the card firmly into place. Use of
excessive force must be avoided; otherwise, the card
might be damaged.
6. Fasten the bracket of the PCI Express card on the back
panel rail of the computer with screws.
7. Connect SFP modules to the SFP ports.
8. Replace the cover of your computer chassis.
9. Plug in the power cord and turn on the computer.
OverviewPacking List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com/eAutomation
For technical support and service:
http://www.advantech.com/support/
This startup manual is for ECU-P1524SPE.
Part No. 2003P15200
Printed in China
1st Edition
June 2018
Declaration of Conformity
Hardware Installation
Specications

2 ECU-P1524SPE Startup Manual
Name Function Interface
A RedBox_A
100M Base-FX SFP Interface
(Select by SFP MODE)
1000M Base-X SFP Interface
(Select by SFP MODE)
B RedBox_B
100M Base-FX SFP Interface
(Select by SFP MODE)
1000M Base-X SFP Interface
(Select by SFP MODE)
InterLink RedBox_
Interlink 10/100/1000 Mbps Base-T
Name Function Interface
A_ACT Blinking SFP module A transmit data
A_Link
Yellow 100M based-fx SFP_A is
linked
Green 1000M based-x SFP_A is
linked
B_ACT Blinking SFP module B transmit data
B_Link
Yellow 100M based-fx SFP_B is
linked
Green 1000M based-x SFP_B is
linked
Mode_1
HSR/PRP
mode
No light Normal switch
Green HSR
Yellow PRP
Mode_2
SFP mode
Yellow 100M based-fx SFP
Green 1000M based-x SFP
Connector and LED Assignments
Switch Mode SW1
Normal Switch OFF OFF OFF OFF
HSR OFF ON OFF OFF
PRP ON ON OFF OFF
SFP Mode SW2
1000M Base-X
100M Base-FX
Switch and Jumper Settings