Advantech TREK-60 User manual

User Manual
TREK-60
Modular AI Platform for Scalable
Surveillance and Fleet
Management

TREK-60 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2021
by Advantech Co., Ltd. all rights reserved. Advantech Co., Ltd. reserves the right to
improve the products described in this manual at any time without notice. No part of
this manual may be reproduced, copied, translated, or transmitted in any form or by
any means without the prior written permission of Advantech Co., Ltd. The informa-
tion provided in this manual is intended to be accurate and reliable. However, Advan-
tech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the
rights of third parties that may result from its use.
Acknowledgments
Intel® is a trademark of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that all of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than the repair personnel authorized by Advantech, or products that
have been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty for any consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers are billed according to the cost of replacement materials,
service time, and freight. Please consult your dealer for more details.
If you believe your product is defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2008EK6000 Edition 1
Printed in Taiwan October 2021

iii TREK-60 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Contact your local supplier for ordering
information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for assistance

TREK-60 User Manual iv
Warnings, Cautions, and Notes
Document Feedback
To assist us with improving this manual, we welcome any comments and constructive
criticism. Please send all feedback in writing to [email protected].
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application soft-
ware, etc.)
A complete description of the problem
The exact wording of any error messages
Warning! Warnings indicate conditions that, if not observed, can cause personal
injury!
Caution! Cautions are included to help prevent hardware damage or data losses.
For example,
“Batteries are at risk of exploding if incorrectly installed. Do not attempt
to recharge, force open, or heat the battery. Replace the battery only
with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.”
Note! Notes provide additional optional information.

v TREK-60 User Manual
Safety Instructions
1. Read these safety instructions carefully.
Veuillez lire attentivement ce manuel d’instructions de sécurité.
2. Retain this user manual for future reference.
Veuillez conserver ce manuel d’instructions pour référence ultérieure.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth to clean. Do not use liquid or spray detergents.
Débranchez l’appareil de toutes les prises de courant avant le nettoyage. Net-
toyez-le uniquement à l’aide d’un chiffon humide. Ne pas utiliser de détergents
liquides ou pulvérisateurs.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
Pour les appareils enfichables, la prise de courant doit être placée près de
l’appareil et facilement accessible.
5. Protect the equipment from humidity.
Protégez l’appareil contre l’humidité.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the device fall may cause damage.
Placez l’appareil sur une surface fiable pendant l’installation. L’abandon ou la
chute de l’appareil pourrait causer des dommages.
7. Do not leave the equipment in an environment where the storage temperature is
below -40 °C (-40 °F) or above 80 °C (175 °F) as it may damage the equipment.
The operating temperature range depends on the specific model.
Ne laissez pas l'équipement dans un environnement où la température de
stockage est inférieure à -40 ° C (-40 ° F) ou supérieure à 80 ° C (175 ° F) car
cela pourrait endommager l'équipement. La plage de température de
fonctionnement dépend du modèle spécifique.
- For models with Intel® i7-7600U CPU and RF/SDP: -20 ~ 50 °C (-4 ~ 122 °F)
- Pour les modèles avec processeur Intel® i7-7600U et RF / SDP: -20 ~ 50 ° C
(-4 ~ 122 ° F)
- For models with Intel® X5-E3940 CPU and RF/SDP: -30 ~ 50 °C (-22 ~ 122 °F)
- Pour les modèles avec processeur Intel® X5-E3940 et RF / SDP: -30 ~ 50 ° C
(-22 ~ 122 ° F)
- For models with Intel® X5-E3940 CPU only: -30 ~ 70 °C (-22 ~ 158 °F)
- Pour les modèles avec processeur Intel® X5-E3940 uniquement: -30 ~ 70 ° C
(-22 ~ 158 ° F)
8. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
Les ouvertures du boîtier sont pour la convection d’air. Protégez l’appareil con-
tre la surchauffe. Ne couvrez pas les ouvertures.
9. Ensure that the voltage of the power source is of the correct voltage and is
earthed before connecting the equipment to a power outlet.
Assurez-vous que la tension de la source d’alimentation est correcte avant de
connecter l’appareil à une prise de courant. La prise de courant doit avoir une
bonne connexion mise à la terre.
10. Position the power cord away from high-traffic areas. Do not place anything over
the power cord. The voltage and current rating of the cord should be greater
than the voltage and current rating marked on the product.
Placez le cordon d’alimentation à l’écart des zones à fort trafic. Ne placez rien
sur le cordon d’alimentation.La tension et le courant du cordon doivent être
supérieurs à la tension et au courant indiqués sur le produit.

TREK-60 User Manual vi
11. All cautions and warnings on the equipment should be noted.
Attention à toutes les précautions et avertissements indiqués sur l’appareil.
12. If unused for a long time, disconnect the equipment from the power source to
avoid damage from transient overvoltage.
Si l’appareil n’est pas utilisé pendant une longue période, déconnectez-le de la
source d’alimentation pour éviter les dommages causés par une surtension
transitoire.
13. Never pour liquid into an opening. This may cause fire or electrical shock.
Ne versez jamais de liquide dans une ouverture. Sinon, cela pourrait provoquer
un incendie ou un choc électrique.
14. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
N’ouvrez jamais l’appareil. Pour des raisons de sécurité, l’appareil ne doit être
ouvert que par un technicien qualifié.
15. If one of the following situations occurs, have the equipment checked by service
personnel:
Si l’un des cas suivants se produit, demandez aide à un technicien qualifié:
The power cord or plug is damaged.
Le cordon d’alimentation ou la fiche est endommagé.
Liquid has penetrated the equipment.
Le liquide a pénétré dans l’appareil.
The equipment has been exposed to moisture.
L’appareil a été exposé à l’humidité.
The equipment is malfunctioning or does not operate according to the user
manual.
L’appareil est défectueux ou ne fonctionne pas conformément aux instruc-
tions.
The equipment has been dropped and damaged.
L’appareil a été abandonné et endommagé.
The equipment shows obvious signs of breakage.
L’appareil montre des signes évidents de rupture.
16. Any unverified component could cause unexpected damage. To ensure correct
installation, always use the components provided in the accessory box.
Tout composant non vérifié peut provoquer des dommages inattendus. Pour
garantir une installation correcte, utilisez toujours les composants fournis dans
la boîte d'accessoires.
17. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
ATTENTION: ll y a danger d’explosion s’il y a rem placement incorrect de la pile.
Remplacer uniquement avec une pile du mème type ou d’un type equivalent
recommandè par le constructeur.
18. CAUTION: This product is not intended for use by children and is not suitable for
use in locations where children are likely to be present (this product is not a toy).
ATTENTION: Ce produit n’est pass un jouet et devrait ètregard Jouet et devrait
ètre gardè hors de la portèe des enfants.

vii TREK-60 User Manual
19. CAUTION: Always ground yourself to remove any static charge before touching
the motherboard, backplane, or add-on cards. Modern electronic devices are
very sensitive to static electric charges. As a safety precaution, use a grounding
wrist strap at all times. Place all electronic components on a static-dissipating
surface or in a static-shielded bag when not installed in the chassis.
ATTENTION: Mettez-vous toujours à la terre pour éliminer toute charge statique
avant de toucher la carte mère, le fond de panier ou les cartes d'extension. Les
appareils électroniques modernes sont très sensibles aux charges électriques
statiques. Par mesure de sécurité, utilisez en tout temps un bracelet antista-
tique. Placez tous les composants électroniques sur une surface dissipant
l'électricité statique ou dans un sac blindé antistatique lorsqu'ils ne sont pas
dans le châssis.
Safety Precautions - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage:
Suivez ces précautions simples pour vous protéger contre les dommages et protéger
les produits contre les dommages:
To avoid electrical shock, always disconnect the power from the PC chassis
before manual handling. Do not touch any components on the main board or
cards while the system is powered on.
Pour éviter tout choc électrique, débranchez toujours l'alimentation du châssis
du PC avant toute manipulation manuelle. Ne touchez aucun composant de la
carte principale ou des cartes lorsque le système est sous tension.
Disconnect the power before implementing any configuration changes. A sud-
den surge of power after connecting a jumper or installing a card may damage
sensitive electronic components.
Débranchez l'alimentation avant d'appliquer des modifications de configuration.
Une surtension soudaine après la connexion d'un cavalier ou l'installation d'une
carte peut endommager les composants électroniques sensibles.
Warning! 1. Rated input voltage: 9 ~ 32 VDC (12/24V power system)
Tension d'entrée nominale: 9 ~ 32 VDC (système d'alimentation 12
/ 24V)
2. Transport: Carry the unit with both hands and handle with care
Transport: portez l'appareil à deux mains et manipulez-le avec pré-
caution
3. Maintenance: Use only a damp cloth to clean the surfaces
Entretien: utilisez uniquement un chiffon humide pour nettoyer les
surfaces
4. Battery/Micro SD/SIM card/SSD: Power off the equipment before
installing or removing any peripherals
Batterie / Micro SD / Carte SIM / SSD: Éteignez l'équipement avant
d'installer ou de retirer des périphériques
5. This product is intended to be supplied by a UL-certified power
supply or DC power source rated 9 ~ 32 VDC, 14A, with a TMA of
40 °C (104 °F) minimum. Should you require additional assistance,
contact Advantech for further information.
Ce produit doit étre certifié par UL pour l'alimentation électrique ou
en courant continu, Tension nominale 9 ~ 32 VDC, 14A, et TMA 40
°C (104 °F), contactez si vous avez besoin d’aide Advantech en
sait plus.

TREK-60 User Manual viii

ix TREK-60 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Key Features............................................................................................. 2
1.3 Modular Design......................................................................................... 3
Figure 1.1 TREK-60 Architecture................................................. 3
Table 1.1: TREK-60 Modular Design SKU .................................. 3
1.4 General Specifications .............................................................................. 4
Table 1.2: Power Input and Output.............................................. 6
Table 1.3: Power Consumption for Intel® Core™ i7-7600U CPU
Model.......................................................................... 7
Table 1.4: Power Consumption for Intel® Atom™ E3940 CPU
Model.......................................................................... 7
1.5 Dimensions ............................................................................................... 8
Figure 1.2 TREK-60 Dimensions ................................................. 8
Chapter 2 System Setup.......................................9
2.1 Introduction ............................................................................................. 10
2.2 Quick Tour............................................................................................... 10
Figure 2.1 TREK-60 Front View................................................. 10
Figure 2.2 TREK-60 Rear View (PoE Configuration)................. 10
Figure 2.3 TREK-60 Front Door with Key Lock Protection ........ 10
Figure 2.4 TREK-60 Front I/O.................................................... 11
Figure 2.5 TREK-60 RF Extension Module ............................... 11
Figure 2.6 TREK-60 I/O View (with PoE)................................... 11
2.3 Installation ............................................................................................... 12
2.3.1 Connecting the Power Cord........................................................ 12
2.3.2 Wake-On-Ignition ........................................................................ 12
2.3.3 Wall and DIN Rail Mounting........................................................ 13
Figure 2.7 TREK-60 Wall and DIN Rail Mounting...................... 13
Table 2.1: Wall Mount Bracket Orientations .............................. 14
2.4 BIOS Setup ............................................................................................. 14

TREK-60 User Manual x

Chapter 1
1General Information

TREK-60 User Manual 2
1.1 Introduction
Advantech’s TREK-60 is a rugged, modular video AI platform aimed at fleet manage-
ment and surveillance applications.
Powered by a 7th generation Intel® Core™ i7/i5/Atom™ E3900 quad-core proces-
sor, TREK-60 supports up to eight camera input channels and AI accelerator expan-
sion to enable scalable video inferences on edge devices. The provision of an RF
extension module with automotive-grade FAKRA connector supports GNSS, WLAN,
Bluetooth, and WWAN technology to enable real-time communication, vehicle track-
ing, and data collection. Moreover, the embedded dual CAN bus supports diverse
vehicle protocols, including raw CAN, J1939, and OBD-II, for vehicle monitoring and
diagnostics, while the intelligent vehicle power management system supports ignition
on/off/delay and wake-up event control. Furthermore, to ensure easy integration and
connection with vehicle systems, TREK-60 features multiple digital I/O with wet and
dry configurations, two 4-wire RS-232/RS-485 ports, and two 2-wire RS-232 ports, as
well as dual audio codec packs.
1.2 Key Features
Intel® Atom™ E3900/Core™ i7/i5 processor
RF extension module with automotive-grade connector (FAKRA) enables easy
installation and customization
Modular I/O expansion facilitates the integration of edge AI modules, 5G com-
munication, and DSRC/V2Xdevices
Eight 802.3at PoE IP camera ports for video surveillance applications
GNSS, WLAN, Bluetooth, and WWAN communication technology
Easily paired with second-generation TREK displays via a single cable
Accessible external SSD tray with key-lock protection
Supports 12/24V input power (ISO 7637-2) with intelligent power management
that supports ignition on/off/delay functions, wake-up event control, and system
monitoring and diagnostics
Wide operating temperature range (-30 ~ 70 °C/-22 ~ 158 °F)
MIL-STD-810G and EN60721-3(5M3) certified for shock and vibration tolerance

3 TREK-60 User Manual
Chapter 1 General Information
1.3 Modular Design
TREK-60 consists of an industrial computer with a ruggedized metal enclosure and
RF and IO extension modules that enable flexible expansion and integration with
existing infrastructure. The modular design allows TREK-60 to be easily customized
for entry-level or high-end computing applications.
Figure 1.1 TREK-60 Architecture
Table 1.1: TREK-60 Modular Design SKU
TREK-60 SKU1 TREK-60 SKU2 TREK-60 SKU2
without RF and SDP
Platform
(blue
components)
Intel® Core™ i7/i5
CPU: i7-7600U
Memory: DDR4
Intel® Atom™ E3900
CPU: X5-E3940
Memory: DDR3L
Intel® Atom™ E3900
CPU: X5-E3940
Memory: DDR3L
Surveillance
(red
components)
8 IPCAM channels
8 ports RJ-45
2.5” SSD tray
8 IPCAM channels
8 ports RJ-45
2.5” SSD tray
8 IPCAM channels
8 ports RJ-45
2.5” SSD tray
Other
features
External RF module
SDP port
GPS
External RF module
SDP port
GPS
N/A

TREK-60 User Manual 4
1.4 General Specifications
Platforms
Intel Apollo Lake Platform (APL):
–Processor: Intel® Atom™ X5-E3940 quad-core, 1.9 GHz
–Memory: 1 x SODIMM socket, supports up to 8 GB of DDR3L 1866/1600
(default configuration: 1 x 4 GB)
–Graphics: Intel® HD Graphics 500
–BIOS: AMI UEFI (64 Mbit) on CPU
Intel Kaby Lake Platform (KBL):
–Processor: Intel® Core™ i7-7600U dual-core 3.9 GHz
–Memory: 2 x SODIMM socket, supports up to 32 GB of DDR4 2133 (default
configuration: 1 x 4 GB)
–Graphics: Intel® HD Graphics 620
–BIOS: AMI UEFI (64 Mbit) on CPU
OS: Windows 10 IoT Enterprise LTSC, 64 bit (default), Ubuntu 18.04, 64 bit
Storage
1 x internal mSATA slot (default) supports up to 64 GB UMLC industrial-grade
storage (32 GB UMLC as default)
1 x externally accessible 2.5” SSD tray (maximum height 9.5 mm) with key-lock
protection, supports an optional TLC industrial-grade SSD up to 3.84 TB
1 x externally accessible micro SD card reader (optional) with push-push mech-
anism and key-lock protection, supports an optional SDHC Class 10 UHS-I MLC
industrial-grade SD card, up to 128 GB (available upon request)
Display (Graphical Output)
1 x DisplayPort 2.0 (for direct pairing with a second generation TREK display via
a single-cable connection) with hot plug detection via a GT32-10-pin automotive
connector:
–12V/2.0A power output for the TREK-306 (1024 x 768 default resolution) and
TREK-303 (800 x 480 default resolution) displays
–1 x High-resolution video and audio input
–1 x USB 2.0
–1 x Power button
–1 x Reset button
1 x HDMI 1.3
Expansion
1 x internal full-size mini-PCIe slot for optional expansion
1 x external RF extension module
1 x external I/O extension module (optional)
Sensors
1 x G-sensor; linear acceleration zero-g level offset accuracy is ±40 mg
1 x Accelerometer and gyroscope
3 x Thermal sensors reserved (for CPU, top side of main board, and underside
of main board)

5 TREK-60 User Manual
Chapter 1 General Information
I/O Interface
Virtual I/O via GT25, 16-pin, automotive connector:
–2 x CAN bus (supports RAW CAN, J1939, OBD-II/ISO 15765; configurable
via firmware)
–1 x J1708 (supports J1587)
–1 x Ignition and BAT power input
Generic I/O via GT25, 40-pin, automotive connector:
–2 x 4-wire RS-232 (default) and RS-485 (switchable in BIOS)
–2 x 2-wire RS-232
–6 x Digital input with 2.5 kV isolation
–Wet/dry configuration via SDK (default for all ports is dry contact)
–Low is up to 1.3V; High is at least 4V; maximum is 36VDC
–4 x Digital output with 2.5 kV isolation
–Output current up to 48V/300mA maximum
–2 x Line out
–2 x Mic in
Standard I/O:
–2 x USB 2.0 host at the rear
–1 x USB 3.0 host at the front with key-lock protection
–2 x GigaLAN (default RJ-45 connector, optional M12 X-coded connector)
LED: 5 x LED, Power (red), Storage (yellow), WLAN (green), WWAN (green),
and GPS (yellow)
Buttons:
–1 x Power button on second generation TREK display (power on ignition as
default)
–1 x Clear CMOS button with key-lock protection
–1 x Reset button with key-lock protection
Video Surveillance
IP Camera:
–8 x RJ-45 for 10/100Mbps
–Supports IEEE802.3af Class 2 (7 W), Class 3 (15.4 W), IEEE802.3at Class 4
(30 W)
–Power output shared with all cameras limited to 61.6W
–SDK support for PoE control
RF (WLAN/WWAN Support via RF Extension)
1 x full-size mini PCIe slot, supports IEEE 802.11a/b/g/n/ac and Bluetooth V5.0
(combo module as default)
1 x full-size mini PCIe slot, supports WWAN (LTE, HSPA+, GSM/GPRS) module
for US/EU bands (Sierra wireless WP7607 for EU and WP7610 for US as
default)
1 x externally accessible mini SIM card socket (with cover), or 1 x optional
embedded SIM available upon request
1 x Built-in u-blox Neo-M8N GPS/GLONASS/BeiDou module with A-GPS sup-
port, or optional Neo-M8U(untethered dead reckoning), Neo-M8L (dead reckon-
ing) upon request
5 x FAKRA-type antenna holes for 1x GPS, 2x WI-FI+BT, 2x WWAN/LTE with
WI-FI/WWAN MIMO supported

TREK-60 User Manual 6
RTC Battery
3.0V @ 200 mAH lithium battery
Watchdog Timer
255-level timer interval, setup by IVCP SDK
Power System
Supports 12/24V power system (ISO 7637-2 and SAE J1113 compliance)
Intelligent Power Management (IVCP FW):
–System power on/off/hibernate management (programmable ignition on/off/
delay)
–Supports wake-up events: wake-on-alarm (RTC), wake-on-call/SMS, and
wake-on-G-sensor
–System power protection (battery low voltage protection)
–System monitoring and diagnostics
–System power usage management (Table 1.3)
–Optional features power usage table (for reference only) (Table 1.4)
Note 1: Supports platform and PoE power management via IVCP firmware
Note 2: Does not support PoE function when input power is 9 ~ 12V
Mechanical Design
Aluminum chassis with IP54-rated ingress protection; IP65-rated protection
available with extended I/O cover (depending on specific I/O ports)
Dimensions (W x D x H): 314 x 165.5 x 75.1 mm/12.36 x 6.51 x 2.95 in
Weight: (without SSD) 4.3 kg/9.47 lb; (without SSD or RF extension module)
3.8 kg/8.37 lb
Environmental Specifications
Operating Temperature:
–-20 ~ 50 °C/-4 ~ 122 °F for TREK-60 SKU 1
–-30 ~ 50 °C/-22 ~ 122 °F for TREK-60 SKU 2
–-30 ~ 70 °C/-22 ~ 158 °F for TREK-60 SKU 2 (without RF/SDP or 40W PoE
limit)
Storage Temperature: -40 ~ 85 °C/-40 ~ 176 °F
Relative Humidity: 95% @ 40 °C/104 °F (non-condensing)
Vibration and Shock Tolerance: MIL-STD-810G, EN60721-3(5M3), SAE J1455,
IP Rating: IP54 or IP65 with optional I/O cover (available upon request)
Power Regulation: E-Mark (E13), SAE J1455, ISO-7637-2, SAE J1113
Safety:
–UL 60950, CSA 60950, IEC/EN 60950 (certified temperature 40 °C/104 °F)
–UL 62368-1, CSA 62368-1, IEC/EN 62368-1 (certified temperature 50 °C/122
°F and 70 °C/158 °F)
Table 1.2: Power Input and Output
Input Power Description Remark
Input 12 ~ 32V Supports platform and POE Note 1
Input 9 ~ 12V Supports platform power only Note 2

7 TREK-60 User Manual
Chapter 1 General Information
EMC:
–Emissions: FCC Part 15 Subpart B Class A, IC ICES-003 Class A, EN 55032
Class A, EN 61000-6-3, EN 61000-3-2, EN 61000-3-3
–Immunity: EN 55035, EN 61000-6-2/EN 61000-6-4
Power Consumption
Note 1: The converter efficiency is 90 ~ 95%. Thus, if the PoE loader setting is 30W,
the input power must be at least 33W (for sufficient power at 90% efficiency).
Note 2: The system tested was a TREK-60 platform equipped with 32 GB UMLC
mSATA, u-Blox NEO-M8N, RF extension module with Wi-Fi and WWAN, SDP 2.0,
and a TREK-306PH2 display.
Note 3: Tested at an environmental temperature of 25 °C/77 °F.
Note 4: Burn-in setting test items: CPU, memory, 2D/3D GPU, video, and SSD.
Table 1.3: Power Consumption for Intel® Core™ i7-7600U CPU Model
Mode PoE Loader SDP2.0 Without SDP2.0
Power off NA 0.096W 0.096W
Idle 0W 34.9W 19.7W
Burn-in
0W 63.6W 47.5W
30W 96.6W 80.5W
60W 129.6W 113.5W
Table 1.4: Power Consumption for Intel® Atom™ E3940 CPU Model
Mode PoE Loader SDP2.0
12/24V
Without SDP2.0
12/24V
Power off NA 0.096W 0.096W
Idle 0W 34.1W/31.7W 16.7W/17.8W
Burn-in
0W 40.7W/37.7W 22.3W/23.5W
30W 73.7W/70.7W 55.3W/56.5W
60W 106.7W/103.7W 88.3W/89.5W

TREK-60 User Manual 8
1.5 Dimensions
Figure 1.2 TREK-60 Dimensions

Chapter 2
2System Setup

TREK-60 User Manual 10
2.1 Introduction
This chapter explains the connector and port pin definitions and provides information
regarding setting up the TREK-60 device.
2.2 Quick Tour
Figure 2.1 TREK-60 Front View
Figure 2.2 TREK-60 Rear View (PoE Configuration)
Figure 2.3 TREK-60 Front Door with Key Lock Protection