AEG Electrolux 88101K-MN User manual

88101K-MN
User manual Ceramic glass induction
hob

Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating Instructions 2
Safety information 2
Description of the appliance 4
Operating the appliance 6
Tips on cooking and frying 12
Cleaning and care 14
What to do if ... 14
Disposal 16
Installation Instructions 17
Safety information 17
Service 19
Warranty 19
Subject to change without notice
Operating Instructions
Safety information
WARNING!
Please comply with these instructions. If you do not, any damage resulting is not covered
by the warranty.
Correct use
• This appliance is not intended for use by children or other persons whose physical, sensory
or mental capabilities or lack of experience and knowledge prevents them from using
the appliance safely without supervision or instruction by a responsible person to ensure
that they can use the appliance safely.
• Do not leave the appliance unattended during operation.
• This appliance should be used only for normal domestic cooking and frying of food.
• The appliance must not be used as a work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials or fusible objects
(e.g. plastic film, plastic, aluminium) on or near the appliance.
Children’s safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
2Contents

• To avoid small children and pets unintentionally switching the appliance on, we recom-
mend activation of the child safety device.
General safety
• The appliance may only be installed and connected by trained, registered service engi-
neers.
• Built-in appliances may only be used after they have built in to suitable built-in units
and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches
or splits), the appliance must be switched off and disconnected from the electrical supply,
to prevent the possibility of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
Safety during use
• Remove stickers and film from the glass ceramic.
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must not touch the hot surface of the appliance or hot
cookware.
• Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
• Switch the cooking zones off after each use.
• Users with implanted pacemakers should keep their upper body at least 30 cm from
induction cooking zones that are switched on.
• Risk of burns! Do not place objects made of metal, such as knives, forks, spoons and
saucepan lids on the cooking surface, as they can get hot.
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning
equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by objects falling onto it.
• The edge of the glass ceramic can be damaged by being knocked by the cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the
glass ceramic if pushed across the surface.
• Objects that melt and things that boil over can burn onto the glass ceramic and should
be removed straightaway.
• Do not use the cooking zones with empty cookware or without cookware.
• To avoid damaging cookware and glass ceramics, do not allow saucepans or frying pans
to boil dry.
• The ventilation gap of 5mm between the worktop and front of the unit underneath it
must not be covered.
Safety information 3

Description of the appliance
Cooking surface layout
3
2
1
54
180
180
145 180/280
1Induction cooking zone 1850 W, with power function 2500 W
2Induction cooking zone 2400 W, with power function 3700 W
3Control panel
4Induction cooking zone 1400 W, with power function 1800 W
5Induction cooking zone 1850 W, with power function 2500 W
Control panel layout
1 2 5
6789
43
1Lock
2Power function
3Heat setting selection
4Cooking zone indicators. Timer function
5Timer display
6Display
7Timer
8Stop+Go
9On/Off with indicator
4Description of the appliance

Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by
touching sensor fields and confirmed by displays and acoustic signals. Only touch the sensor
fields which activate a desired function. Do not cover other sensor fields.
If the control bar is touched for longer than 6 seconds, a signal sounds and the appliance
switches itself off.
Sensor field Function
On / Off Switches appliance on and off
Increase settings To increase Timer setting
Reduce settings To reduce Timer setting
Timer Timer selection
Lock Locking/unlocking the control panel
Power Switch the power function on and off
STOP+GO To switch the Keep Warm setting on and off
Increase settings To increase heat setting
Reduce settings To reduce heat setting
Displays
Display Description
The cooking zone is switched off
Keep Warm settings Keep Warm / STOP+GO function is switched on
- Heat settings To set heat settings
- Heating setting plus
decimal point
Intermediate heat setting is set
Auto Warm-up The Auto Warm-up function is switched on
Fault Malfunction has occurred
Pan detection Cookware is unsuitable or too small or no cookware
has been placed on the cooking zone
Residual heat Cooking zone is still hot
Child safety device Lock/Child safety device is set
Power Power function is switched on
Automatic Switch off Switch off is active
Residual heat indicator
WARNING!
Risk of burns from residual heat. After being switched off, the cooking zones need some
time to cool down. Look at the residual heat indicator .
Description of the appliance 5

Residual heat can be used for melting and keeping food warm.
The induction cooking zones create the heat required for cooking directly in the base of
the cookware. The glass ceramic is merely heated by the residual heat of the cookware.
Operating the appliance
Use the induction cooking zones with suitable cookware.
Switching the appliance on and off
Control panel Display Pilot light
Switch on Touch for 2 seconds / lights up
Switch off Touch for 1 second / none goes out
After switching on, within approx. 10 seconds a heat setting or a function must be set,
otherwise the appliance automatically switches itself off.
Setting the heat setting
Control panel Display
Increase Touch to /
Decrease Touch to
Switch off Touch and at the same time
The keep warm setting lies between and . It is used to keep food warm.
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm-up function. The automatic warm-
up function sets the cooking zone to the highest setting for a certain period of time and
then automatically switches back to the cooking setting that was originally set.
Step Control panel Display
1. Setting the maximum setting /
2. Place to one side for a moment /
3. Touch
4. Touch in order to set the desired cooking setting Until / after 3
seconds
If during the automatic warm up a higher heat setting is selected, e.g. from to ,
the automatic warm up is adjusted.
The length of time that the automatic warm up function operates depends on the heat
setting selected.
6Operating the appliance

Heat setting
Length of the auto-
matic warm up
[min:sec]
Intermediate heat set-
ting
0:10
0:10
0:10 1:20
3:10 4:20
5:50 8:10
10:10 10:30
2:00 2
2:30
2:50
---
Locking/unlocking the control panel
The control panel, with the exception of the “On/Off” sensor field, can be locked at any time
in order to prevent the settings being changed e.g. by wiping over the panel with a cloth.
Control panel Display
Switch on Touch (for 5 seconds)
Switch off Touch previously set heat setting
When you switch the appliance off, the locking function is automatically switched off.
Turning the STOP+GO function on and off
The STOP+GO function simultaneously toggles all active cooking zones to keep-warm mode
then back to the heat setting they were at before
Control panel Display
To switch on Touch
To switch off Touch Previous heat setting (not automatic warm-up or power
function)
STOP+GO does not stop timer functions.
STOP+GO controls the entire control panel apart from the sensor field .
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Operating the appliance 7

Setting the child safety device
Step Control panel Display/Signal
1. Switch on the appliance. Do not set a heat setting.
2. Touch until the signal sounds Acoustic signal
3. Touch
Appliance switches off. The child safety device is engaged.
Overriding the child safety device
The child safety device can be released in this way for a single cooking session; it remains
activated afterwards.
Step Control panel Display/Signal
1. Switch on the appliance
2. Touch and at the same time / acoustic signal
Until the appliance is next switched off, it can used as normal.
Releasing the child safety device
Step Control panel Display/Signal
1. Switch on the appliance
2. Touch until the signal sounds Acoustic signal
3. Touch
Appliance switches off. The child safety device is released.
Switching the power function on and off
The power function makes additional power available to the front induction cooking
zones, e.g. to bring a large volume of water to the boil. The power function is activated for
8 minutes for the front left cooking zone and for 5 minutes for the front right cooking
zone. After these times, the induction cooking zones automatically return to cooking level
.
Control panel Display
Switch on Touch
Switch off Touch
Touch
If the power function has ended, the cooking zones automatically switch back to the heat
setting set previously.
8Operating the appliance

Power Management
The cooking zones of the cooking surface have a
maximum power.
The maximum power is reached when the heat
setting 9 has been set for all cooking zones.
Two cooking zones generate a pair (see figure)
and therefore, the power management shares the
maximum available power between these cook-
ing zones.
When the power function is selected for one
cooking zone, the power management makes the
additional power for this cooking zone available
by reducing the power of the corresponding oth-
er cooking zone.
Example: the heat setting 9 is selected on one cooking zone. The power function is switched
on for the corresponding cooking zone. The power function is carried out but the heat
setting 9 of one of the cooking zones and the power function for the other cooking zone
of the pair exceed the maximum power for both at the same time. For this purpose, the
power management reduces the power of the cooking zone that switched on first from 9
to example 5 and the display of this cooking zone changes between 9 and 5 and then stays
at the current possible maximum 5. (If the display changes between 9 and 5 or 9 and 3 or
another value depends on the type of appliance and the size of the cooking zone.).
Using the timer
All cooking zones can use each use one of the two timer functions at the same time.
Function Condition Outcome after the time has elapsed
Automatic cut-out a heat setting is set acoustic signal
00
flashes Cooking
zone switches off
Countdown timer cooking zones not in use acoustic signal
00
flashes
If a cooking zone is switched off, the timer function set is also switched off.
If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking
zone is switched off after the time set has elapsed.
Selecting a cooking zone
Ste
p
Control panel Display
1. Touch once Pilot light of the first cooking zone flashes
2. Touch once Pilot light of the second cooking zone flashes
3. Touch once Pilot light of the third cooking zone flashes
Operating the appliance 9

Ste
p
Control panel Display
4. Touch once Pilot light of the fourth cooking zone flashes
The heat setting indicator of the selected cooking zone goes out, as long as the timer time
can be set.
If the pilot light is flashing more slowly, the heat setting indicator appears again and the
heat setting can be re-set or modified.
If other timer functions are set, after a few seconds the shortest remaining time of all the
timer functions is displayed and the corresponding pilot light flashes.
Setting time
Step Control panel Grill seting
1. Selecting cooking zone Telltale of cooking zone selected flashes
2. Touch or from the selected cooking
zone
0
1
to
99
minutes
After a few seconds the power indicator flashes more slowly.
The time is set.
The time counts down.
Switching off the Timer function
Step Control panel Display
1. Select a cooking zone Pilot light of the selected cooking zone
flashes more quickly. Remaining time is
displayed
2. Touch for the cooking zone selected The remaining time counts down to
00
.
Simultaneously Touch and from the
selected cooking zone
00
is displayed.
The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
Changing the time
Step Control panel field Display
1. Select cooking zone Pilot light of the cooking zone selected flashes
faster The time remaining is displayed
2. Touch or for the cooking zone
selected
0
1
to
99
minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
10 Operating the appliance