Aegis AVP-CBS2K-101 User manual

Version:201007V1.1
AVP-CBS2K-101
IP Controller
This Quick Start Guide is for installation only. For complete user manual go to www.aegis4av.com
User Manual

Important Safety Instructions
1. Do not expose this apparatus
to rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
6. Clean this apparatus
only with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
5. Do not place sources of naked
flames, such as lighted candles,
on the unit.
7. Unplug this apparatus
during lightning storms or
when unused for long
periods of time.
8. Protect the power cord
from being walked on or
pinched particularly at
plugs.
9. Only use attachments /
accessories specified by
the manufacturer.
10. Refer all servicing to
qualified service
personnel.

Warnings of FCC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and decoder.
-- Connect the equipment into an outlet on a circuit different from that to
which the decoder is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Table of Contents
Introduction.......................................................................1
Features ......................................................................1
Package Contents .......................................................1
Specifications....................................................................2
Panel Description..............................................................3
Front Panel..................................................................3
Rear Panel...................................................................4
Installation.........................................................................6
Warranty ...........................................................................7

Introduction
AVP-CBS2K-101 (hereinafter referred to as IP controller) is an IP control box
that is used as an A/V control device for controlling, configuring and managing
encoders and decoders on the local area network. It integrates two Ethernet
ports and two RS232 ports, offering integration-friendly control
features——LAN (Web GUI & Telnet). It also can be used with a third party
controller to provide a simple, flexible control and management options. IP
controller can automatically search and display encoders and decoders. It is
designed to be compatible with the configuration file from PC configurator
(HDMI over IP Console) and use the imported configuration file to perform
operations on encoders and decoders such as matrix and video wall.
Features
IP control via LAN (Web GUI & Telnet) and a third party controller
Features two Ethernet ports and two RS232 ports
Discover encoders and decoders automatically
Supports matrix switching between encoders and decoders
Compatible with the configuration file from PC configurator to quickly
perform operations on encoders and decoders, such as matrix and video
wall
Web configuration page
Package Contents
1 x IP Controller
1 x Power Supply (12 V 1A DC)
1 x Detachable Plug
1 x Phoenix Connector (Male, 3.5 mm, 6 pins)
2 x Mounting Ear
5 x Label Card (49 mm x 15 mm)

Specifications
Technical
I/O Connections
1 x LAN1 (AV/POE) (10/100 Mbps)
1 x LAN2 (C) (10/100 Mbps)
2 x RS232
LED
1 x STATUS LED
1 x POWER LED
Button
1 x RESET Button
Control Method
LAN (Web GUI & Telnet), RS232 and a third party
controller
General
Power Supply
12 VDC 1 A
Power Consumption
4.5 W Max. (without outputting 12 V 0.5 A using
RS232 port)
10.5 W Max. (with outputting 12 V 0.5 A using
RS232 port)
Operating Temperature
32°F ~ 113°F (0°C ~ +45°C)
10% ~ 90%, non-condensing
Storage Temperature
-4°F ~ 140°F (-20°C ~ +70°C)
10% ~ 90%, non-condensing
Surge Protection
Voltage: ±1000 V
(Tested ten times respectively for the positive and
negative voltages)
ESD Protection
Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Product Dimension
(W x H x D)
93.2 mm x 26 mm x 138.7 mm/3.67'' x 1.02'' x 5.46''
Case Dimension
(W x H x D)
170 mm x 80 mm x 250 mm/6.69'' x 3.15'' x 9.84''
Weight
0.38 kg / 0.84 lbs (without accessories)

Panel Description
Front Panel
No.
Name
Description
1
Label Card
Location
Inserts a supplied label card intended for writing
short notes such as an IP address.
2
STATUS
LED
Blue: when IP controller is working properly.
Off: when IP controller is powered off or is
booting.
3
POWER
LED
Red: when IP controller is powered on.
Off: when IP controller is powered off.
4
RESET
When IP controller is powered on, use a pointed
stylus to hold down RESET button for five or more
seconds, and then release it. It will reboot and
restore to its default settings.
Note: When the default settings are restored, your custom
data is lost. Therefore, exercise caution when using the
RESET button.

Rear Panel
21 3
No.
Name
Description
1
RJ45 ports
1 x LAN1 (AV/POE):
Connects to a switch for communication with encoders
and decoders on the same network.
Default protocol:
IP Address
169.254.1.1
Subnet Mask
255.255.0.0
Gateway
169.254.1.254
DHCP
Off
Link speed and
duplex level
Auto detected
Ethernet port indicators:
Green Link LED: this green colored LED lights when
the device actively communicates with a network
Amber Activity LED : this amber colored LED
flickers as the device is connected to a network.
1 x LAN2 (C):
Connects to a third party controller for controlling,
configuring and managing SC009, encoders and decoders
through LAN control (Web GUI & Telnet).
Default protocol:
IP Address
192.168.11.243
Subnet Mask
255.255.0.0
Gateway
192.168.11.1
DHCP
Off
Link speed and duplex level
Auto detected

No.
Name
Description
Ethernet port indicators :same as above
Note:
Only LAN1 (AV/POE) port supports PoE. You can
connect it to a PoE switch to receive power,
eliminating the need for a nearby power outlet.
We would recommend that you power IP controller
using either a power adapter or a PoE switch instead
of using both them at the same time. For example, if
you want to use a power adapter, ensure that PoE
function of the connected LAN port in the switch is
disabled or a non-PoE switch is used.
2
RS232 ports
Left (DEBUG): Pins TX, RX, G are used for device
troubleshooting only.
RS232 parameters:
Baud Rate
115 200 bps
Data Bits
8 bits
Parity
None
Stop Bits
1
Middle (Control): Pins G, RX, TX are used for controlling,
configuring and managing IP controller, encoders and
decoders through RS232 software or a third party
controller.
RS232 parameters:
Baud Rate
9 600 bps
Data Bits
8 bits
Parity
None
Stop Bits
1
Right (Power): Pins G, 12V are used for providing a 12
VDC 0.5 A output.
Note: Please connect the correct pins for device debug
and control. When IP controller is powered by a power
adapter, if you connect control terminal to control port after
first connection with the debug port, you need to reboot IP
controller for device control process.
3
DC 12V
Connects to a supplied 12 VDC 1 A power adapter.

Installation
Note: Before installation, please ensure the device is disconnected from the
power source.
Steps to install the device in a suitable location:
1. Remove the four screws from the two side panels.
2. Position and install the mounting brackets on the two side panels using the
mounting screws provided in package.
3. Mount and secure the device to a surface or a suitable location with the
mounting screws (provided by others).