Aegis PFS-10 User manual

PFS-10 PFS-20 PFS-30
PERSONAL FIREPROOF SAFE
Owner’s Manual
PRIMETAL SECURITY PRODUCTS
WARNING
!
Keep your safe closed and locked at all times when not in use.
PRIMETAL SECURITY PRODUCTS

1. Do not leave safe unattended while open.
2. Keep Children Away from safe.
3. Keep your safe locked and closed at all times when not in use.
4. Place your safe in a cool and dry location.
5. Remember to record the serial number of your safe from the tag on the
back of your safe. You will need this serial number for all warranty or
customer service inquiries.
6. Electronic media, photographic media and all audio-visual media should
not be stored in the safe for fire protection.
IMPORTANT NOTICES
Safe must be secured as detailed in these instructions.Failure to secure the
safe can result in death or serious injury.
WARNING
!
PRODUCT DIAGRAM
Photo of inside of safe Photo of outside of safe
2 3
7
6
8
4
9
5
1
1. Bolts
2. Reset Button
3. Battery Compartment
4. Knob
5. Back-up Key Cover
6. Yellow Indicator Light
7. Red Indicator Light
8. Green Indicator Light
9. Back-up Keys
OPENING THE SAFE FOR THE FIRST TIME
1. Remove the Back-up key cover away.
2. Insert the Back up key into the keyhole and turn clockwise. At the same
time, turn the knob (master key) clockwise to open the door.
WARNING: Do not store your back up keys inside the safe.
1 2

TURNNG THE KEYPAD SOUND OFF/ON WIH MUTE-SYSTEM
BATTERY INSTALLATION AND REPLACEMENT UNLOCKING THE SAFE
1. Pull out the battery compartment cover and lift up the battery box,
carefully insert 4 AA batteries. Follow the posirive (+) and negative (-)
guides in the compartment. Then put the box back.
2. Snap the battery cover back into place.
NOTE: Green linght flashing indicates the operation is correct and successful.
During the use of safe, Yellow light flashing indicates low battery.
PROGRAMMING YOUR PASSCODE
1. Access reset button by removing red cap.
2. Press the reset button, there will be 1 beep with 1green light flash.
3. Input 3-8 digits in 3 seconds, each input will result in 1 beep and 1
green light flash, then press “LOCK” to confirm. There will be 2 beeps
with a flashing green light. It means new code was successful.
4. If the red light flashes twice with beeps, the code failed. Press reset
button again and repeat code programming sequence.
5. If you forget your code, you can use your back up keys at any time to
open your safe and reset the code.
NOTE: Factory Pass Code is “1-5-9-LOCK”.
1. Press your new code (3-8 digits), each input results with green light
flashes with 1 beep.
2. Press"LOCK " to confirm, there will be 2 beeps and the green light
flashes twice. It means the operation is correct. Turn the knob
clockwise to open the door.
3. If the red light flashes three times with 3 beeps, the operation is
failed Please enter your code again.
NOTE: If 3 invalid code attempts are made in succession, this will cause 5
beeps with the red light flashes 5 times and lock the user out for 60 seconds.
You can still use your back up key at any time to open the safe.
If invalid code is entered again, it will be 5 beeps with the red light flashes
5 times and the user will be locked out 5 minutes.
You can mute / unmute the keypad by entering the "CLEAR” button with
1 green light flash.
NOTE: 1. In the factory settings, the sound has been turned on.
2. During the self-locking, no operation is available.
3 4

TOOLS REQUIRED
LOCKING THE SAFE
Drill
3/8” Drill Bit
3/16” Drill Bit
10 mm Socket Wrench
Flat Head Screwdriver
HARDWARE INCLUDED
SECURING THE SAFE
M8×70 mm(2”long) Lag Screws
Washers
Plastic Masonry Anchors
Installation may vary, please contact your local Hardware
Professional for additional installation recommendations.
To lock your safe, simply close the door and turn the knob counterclockwise.
For optimal security, this safe must be mounted to the floor. Failure to do
so will compromise the safety, security and warranty of the safe. Place your
safe in a cool and dry location
Remember to record the serial number of your safe from the tag on the
back of your safe.You will need this serial number for customer serice inquiries.
E-mail: [email protected]
Primetal LLC.
Office: 1150 S Milliken Ave, #1082, Ontario, CA91761, United States
For Customer Service needs, please contact us at:
www.primetalsafe.com
(4)
(4)
(4)
5 6