AEMC instruments Simple Logger AmpFlex AL24-2500 User manual

Simple Logger®
AmpFlex™ Current Probes
AL24-2500 / AL36-2500
AL24-5000 / AL36-5000
USER MANUAL

Limited Warranty
The AmpFlex™ Current Probes are warranted to the owner for a period
of one year from the date of original purchase against defects in
manufacture. This limited warranty is given by AEMC®Instruments, not
by the distributor from whom it was purchased. This warranty is void if
the unit has been tampered with, abused or if the defect is related to
service not performed by AEMC®Instruments.
For full and detailed warranty coverage, please read the Warranty
Coverage Information, which is attached to the Warranty
Registration Card (if enclosed) or is available at www.aemc.com.
Please keep the Warranty Coverage Information with your records.
What AEMC®Instruments will do:
If a malfunction occurs within the one-year period, you may return the
instrument to us for repair, provided we have your warranty registration
information on file or a proof of purchase. AEMC®Instruments will, at its
option, repair or replace the faulty material.
REGISTER ONLINE AT:
www.aemc.com
Limited Warranty
What you must do to return an Instrument for Warranty Repair:
First, request a Customer Service Authorization Number (CSA#) by
phone or by fax from our Service Department (see address below), then
return the instrument along with the signed CSA Form. Please write the
CSA# on the outside of the shipping container. Return the instrument,
postage or shipment pre-paid to:
Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments
Service Department
15 Faraday Drive • Dover, NH 03820 USA
Tel: [phone] (Ext. 360)
[phone] (Ext. 360)
Fax: [phone] or [phone]
[email protected]
Caution: To protect yourself against in-transit loss, we recommend you
insure your returned material.
NOTE: All customers must obtain a CSA# before returning any
instrument.

2
Table of Contents
Warning ................................................................................................... 3
International Electrical Symbols .............................................................. 3
Receiving Your Shipment........................................................................ 4
Packaging................................................................................................ 4
Specifications .......................................................................................... 4
Features .................................................................................................. 6
Indicators and Buttons...................................................................... 6
Inputs and Outputs ........................................................................... 6
Range Selection ............................................................................... 6
Battery Installation ............................................................................ 7
Operation................................................................................................. 7
Software .................................................................................................. 8
Minimum Computer Requirements................................................... 8
Installation......................................................................................... 8
Using the Software ........................................................................... 9
Cleaning .................................................................................................. 9
Repair and Calibration .......................................................................... 10
Technical Assistance and Sales ........................................................... 10

Simple Logger®AmpFlexCurrent Probes
3
Warning
These safety warnings are provided to ensure the safety of personnel
and proper operation of the instrument.
 Read the instruction manual completely and follow all the safety
information before attempting to use or service this instrument.
 Use caution on any circuit: Potentially high voltages and currents may
be present and may pose a shock hazard.
 Read the specifications section prior to using the probes. Never
exceed the maximum voltage ratings given.
 Safety is the responsibility of the operator.
 For maintenance, use only original replacement parts.
 NEVER open the back of the instrument while connected to any circuit
or input.
 ALWAYS inspect the instrument and leads prior to use. Replace any
defective parts immediately.
 NEVER use the Simple Logger®AmpFlex™ Current Probes on
electrical conductors rated above 600V in overvoltage category III
(CAT III).
International Electrical Symbols
This symbol signifies that the loggers are protected by double or
reinforced insulation. Use only specified replacement parts when
servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer
to the user manual before using the instrument.
For more information about the Logger, refer to CD-ROM: USER GUIDE

Simple Logger®AmpFlexCurrent Probes
4
Receiving Your Shipment
Upon receiving your shipment, make sure that the contents are
consistent with the packing list. Notify your distributor of any missing
items. If the equipment appears to be damaged, file a claim immediately
with the carrier and notify your distributor at once, giving a detailed
description of any damage.
Packaging
The AmpFlex™ Current Probes include the following:
 User manual
 One 9V battery
 CD-ROM containing the Windows®98, ME, 2000 and NT
download and graphic software, a generic user guide, product specific
manual and the Simple Logger®catalog.
 6 ft RS-232 cable
Specifications
ELECTRICAL
Number of Channels: 1
Current Ranges: 2
Input: AL24/36-2500 - 250/2500 Arms (internally selectable)
AL24/36-5000 - 500/5000 Arms (internally selectable)
Input Connection: Permanent Flexible Sensor
*Accuracy: 1%R ±1ct
Resolution:
AL24/36-2500: 250 Arms AL24/36-2500: 2500 Arms
Scale Range Maximum Input Resolution Scale Range Maximum Input Resolution
100% 250 Arms 1 Arms 100% 2500 Arms 10 Arms
50% 125 Arms 0.5 Arms 50% 1250 Arms 5 Arms
25% 62.5 Arms 0.25 Arms 25% 625 Arms 2.5 Arms
12.5% 31.25 Arms 0.125 Arms 12.5% 312.5 Arms 1.25 Arms
AL24/36-5000: 500 Arms AL24/36-5000: 5000 Arms
Scale Range Maximum Input Resolution Scale Range Maximum Input Resolution
100% 500 Arms 2 Arms 100% 5000 Arms 20 Arms
50% 250 Arms 1 Arms 50% 2500 Arms 10 Arms
25% 125 Arms 0.5 Arms 25% 1250 Arms 5 Arms
12.5% 62.5 Arms 0.25 Arms 12.5% 625 Arms 2.5 Arms

Simple Logger®AmpFlex™Current Probes
5
Sample Rate: 4096/hr max.
Data Storage: 8192 readings
Data Storage Technique: (TXR™) Time Extension Recording™
Power: 9V Alkaline NEDA 1604, 6JF22, 6LR61
Battery Life Recording: 6 months continuous recording @ 25°C
Output: RS-232 via 5-pin circular connector; 1200 Bps
INDICATORS
Operation Mode Indicator: One Red LED
• Single Blink: STANDBY mode
• Double Blink: RECORD mode
• No Blinks: OFF mode
• Continuously On: Overload condition
CONTROLS
Operation Mode: Push Button, Internal Range: Slide Switch
ENVIRONMENTAL
Operating Temperature: -4 to +158°F (-20 to +70°C)
Storage Temperature: -4 to +174°F (-20 to +80°C)
Relative Humidity: 5 to 95% non-condensing
MECHANICAL
Size: 2-1/2 x 1-9/16 x 4-1/2” (63.5 x 40.64 x 114.3mm)
Maximum Conductor Size: 24" length: 8" Ø; 36" length: 12" Ø
Case: Weatherproof NEMA4X, IP65 rated
SAFETY Working Voltage: IEC 1010-1, 600V, Cat III
ORDERING INFORMATION
Simple Logger®AmpFlex™Model AL24-2500................... Cat. #2113.72
Simple Logger®AmpFlex™Model AL36-2500................... Cat. #2113.73
Simple Logger®AmpFlex™Model AL24-5000................... Cat. #2113.74
Simple Logger®AmpFlex™Model AL36-5000................... Cat. #2113.75
ACCESSORIES
Replacement 6 ft RS232 cable with DB9F........................ Cat. # 2114.27
*Reference condition: 23°C ±3K, 20 to 75% RH, Frequency 45-3000Hz, No AC external magnetic field,
DC magnetic field ≤40A/m, centered conductor, battery voltage 9V ±10%.

Simple Logger®AmpFlexCurrent Probes
6
Features





600 V CAT III

   
 !
!
"
BATTERY: 9 V, NEDA1604, 6LF22, 6LR61
99 CHAUNCY STREET  BOSTON MA 02111, USA
[phone]  Fax [phone]  www.aemc.com
MADE IN USA
 
1. Press to Start Logging
(Logging = Two Blinks)
2. Press to Stop Logging
(Stand-By = One Blink)
3. Press & Hold sec. to Shut Off
(Off = No Blinks)
Warning: All Data will be Deleted!
#$%& ''
®
13
4
(1) Start/Stop Button
(2) Flexible Sensor Input
(3) Operation Mode Indicator
(4) RS 232 Interface
Indicators and Buttons
The AmpFlex™ Logger has only one button and one indicator. Both are
located on the front panel.
The button is used to start and stop recordings and to turn the logger on
and off. The red LED indicates the status of the logger; OFF, STANDBY
or RECORDING. When the LED is lit continuously, it indicates an
overload condition.
Inputs and Outputs
The top of the logger incorporates a
permanent flexible sensor attached
by a 5ft. lead.
HI
LO
HI
LO
The bottom has a 5-pin circular
connector used for serial data
transmission from the logger to your
computer.
Range Selection
Before operating, determine the
maximum current to be logged.
Remove the back cover and select
the appropriate range as shown.

Simple Logger®AmpFlexCurrent Probes
7
Battery Installation
Under normal conditions, the battery will last up to 6 months of
continuous recording unless the logger is restarted very frequently.
In the OFF mode, the logger puts almost no load on the battery. Use the
OFF mode when the logger is not in use. Replace the battery every six
months in normal use.
If the logger will be used at temperatures below 32°F (0°C) or is
frequently turned on and off, replace the battery every three to four
months.
1. Make sure your logger is turned off (no light blinking) and all
inputs are disconnected.
2. Turn the logger upside down. Remove the four Phillips head
screws from the base plate, then take off the base plate.
3. Locate the two-wire (red/black) battery connector and attach the
9V battery to it. Make sure that you observe polarity by lining up
the battery posts to the proper terminals on the connector.
4. Once the connector is plugged onto the battery, insert the battery
into the holding clip on the circuit board.
5. If the unit is not in record mode after installing the new battery,
disconnect it and press the button twice then reinstall the battery.
6. Reattach the base plate using the four screws removed in step
two.
Your logger is now recording (LED blinking). Press the test button for 5
seconds to stop the instrument.
Note: For long-term storage, remove the battery to prevent discharge
effects.
Operation
Position the AmpFlexsensor around the conductor to be measured. Be
sure that the positioning of the logger sensor does not violate the
minimum allowable bending radius of 0.75 inches (19mm).
Next, press the start/stop button on the front of the unit to begin the
recording session. The indicator light will double blink to indicate that the
recording session has started. When the recording session has been
completed, press the start/stop button to end the recording. The indicator
light will single blink to indicate that the recording session has ended and
the unit is in stand-by. Remove the logger from the conductor and
transport it to the computer for data downloading. See the User Guide for
downloading instructions.

Simple Logger®AmpFlexCurrent Probes
8
SOFTWARE
This model requires software version 6.11 or higher.
MINIMUM COMPUTER REQUIREMENTS
Processor: 486 or higher
RAM Storage: 8MB
Hard Drive Space: 8MB for application, approx. 400K for each stored file
Environment: Windows®98, 2000, ME, NT and XP
Port Access: (1) 9-pin serial port and (1) parallel port for printer support
INSTALLATION
Your Simple Logger®software is supplied on a CD-ROM. To install the
program, perform the following steps:
Auto Run Disabled: If Auto Run is disabled, insert the Simple Logger®
CD into the CD-ROM drive, then select Run from the Start Menu. In the
dialog box that appears, type: D:\setup, then click the OK button.
NOTE: In this example, your CD-ROM drive is assumed to be drive letter
D. If this is not the case, substitute the appropriate drive letter.
Auto Run Enabled: If Auto Run is enabled, insert the Simple Logger®
CD into the CD-ROM drive and follow the on-screen prompts to
complete the setup.
 Select Simple Logger 6.11
 Select Acrobat Reader to install Acrobat Reader version 5.0
 Select Explore CD to view the User Guide, Simple Logger®Catalog or
user specific manuals in PDF format.
To view the documents included on the CD-ROM, you must have
Acrobat Reader installed on your machine. If you do not have it installed,
you can install it from the Simple Logger®Software CD-ROM.
Installing Acrobat Reader: Select Run from the Start Menu. In the
dialog box that appears, type: D:\Acrobat\setup, then click OK.
NOTE: In this example, your CD-ROM drive is assumed to be drive letter
D. If this is not the case, substitute the appropriate drive letter.

Simple Logger®AmpFlexCurrent Probes
9
USING THE SOFTWARE
Launch the software and connect the RS-232 cable from your computer
to the logger.
Note: The first time the program is launched you will need to select a
language.
Select “Port” from the menu bar and select the Com port you will be
using (see your computer manual). Once the software automatically
detects the baud rate, the logger will communicate with the computer. (ID
number of the logger and number of points recorded displayed).
Depending on the selected range, “ALXX-2500” or “ALXX-250” will be
displayed and automatically scale the graph accordingly.
Cleaning
The body of the logger should be cleaned with a cloth moistened with
soapy water. Rinse with a cloth moistened with clean water. Do not use
solvent.

AmpFlexCurrent ProbesSimple Logger®
10
Repair and Calibration
To ensure that your instrument meets factory specifications, we recommend
that it be submitted to our factory Service Center at one-year intervals for
recalibration, or as required by other standards or internal procedures.
For instrument repair and calibration:
You must contact our Service Center for a Customer Service Authorization
number (CSA#). This will ensure that when your instrument arrives, it will be
tracked and processed promptly. Please write the CSA# on the outside of
the shipping container. If the instrument is returned for calibration, we need
to know if you want a standard calibration, or a calibration traceable to
N.I.S.T. (includes calibration certificate plus recorded calibration data).
Chauvin Arnoux®, Inc.
d.b.a. AEMC®Instruments
15 Faraday Drive
Dover, NH 03820 USA
Tel: [phone] (Ext. 360)
[phone] (Ext. 360)
Fax: [phone] or [phone]
[email protected]
(Or contact your authorized distributor)
Costs for repair, standard calibration, and calibration traceable to N.I.S.T. are
available.
NOTE: All customers must obtain a CSA# before returning any
instrument.
Technical and Sales Assistance
If you are experiencing any technical problems, or require any assistance
with the proper operation or application of your instrument, please call, mail,
fax or e-mail our technical support hotline:
Chauvin Arnoux®, Inc.
d.b.a. AEMC®Instruments
200 Foxborough Boulevard
Foxborough, MA 02035, USA
Phone: [phone]
[phone]
Fax: [phone]
[email protected]
www.aemc.com
NOTE: Do not ship Instruments to our Foxborough, MA address.

Chauvin Arnoux®, Inc. d.b.a AEMC®Instruments
15 Faraday Drive • Dover, NH 03820
www.aemc.com
99-MAN 100208 v901/05