Aeotec Range Extender 6 User manual

View the expanded manual:
http://aeotec.com/support
Aeotec by Aeon Labs Range Extender.
Aeotec Range Extender is a Z-Wave mesh
network repeater which can extend the range of
communication between Z-Wave products and
assist other devices to reach each other in your
Z-Wave network.
The Range Extender can also communicate securely
via AES 128 wireless Z-Wave commands and
supports Over-The-Air (OTA) rmware upgrades.
Familiarise yourself with your Range
Extender.
Getting your Range Extender up and running is as
simple as plugging it into a wall outlet and adding
it to your Z-Wave network. To set your Z-Wave
controller/gateway into pairing mode, please refer
to the respective section within your controller
instruction manual.
Quick start. 1.
2.
3.
4.
Set your Z-Wave Controller into device removal
mode.
In order to take full advantage of all functionality
the Range Extender, you may want your Range
Extender is a security device that uses secure/
encrypted message to communicate in your Z-Wave
network, so a security enabled controller/gateway is
needed.
Decide on where you want your Range Extender
to be placed and then plug it into a wall outlet.
Set your Z-Wave Controller into pairing mode.
Press the Z-Wave Button on your Range
Extender.
If Range Extender has been successfully added
to your Z-Wave network, its RGB LED will be
solid. If the adding was unsuccessful, the red LED
will be on for 2 seconds and then remain colourful
gradient status, repeat the steps above.
1.
Range Extender 6
1
2
3
IMPORTANT!
This product has been fully tested and certied
to work with Z-Wave by the Z-Wave Alliance. It
is crafted using Z-Wave Plus, the latest device
version of Z-Wave. As such, if the product does
not work with your gateway, please be sure to
check with your gateway manufacturer that they
have integrated this device with their gateway for
full operation.
Adding your Range Extender into a Z-Wave
network.
Fixing hole
Z-Wave Button
Network LED
Removing your Range Extender from a
Z-Wave network.
Your Range Extender can be removed from your
Z-Wave network at any time. You’ll need to use
your Z-Wave network’s main controller. To set your
Z-Wave controller/gateway into removal mode,
please refer to the respective section within your
controller instruction manual.
2.
3.
Press the Z-Wave Button on your Range
Extender.
If Range Extender has been successfully removed
from your network, its RGB LED will remain
colourful gradient status. If the removal was
unsuccessful, the RGB LED will still be solid,
repeat the steps above.
Enabling Security Encryption.
1.
2.
3.
Set your Z-Wave security controller/gateway into
pairing mode.
Press the Z-Wave Button 2 times within 1 second.
If the Range Extender has been successfully
added to your Z-Wave network, its blue LED will
be solid for 2 seconds and then be off. Otherwise,
Model number: ZW117.
Operating temperature: 32°F to 104°F/0°C to 40°C.
Relative humidity: 8% to 80%.
Operating distance: Up to 492 feet/150 meters
outdoors.
Technical Specications.
Resetting your Range Extender.
If at some stage, your primary controller is missing
or inoperable, you may wish to reset all of your
Range Extender’s settings to their factory defaults.
To do this, press and hold the Z-Wave Button
for 20 seconds and then release it. Your Range
Extender will now be reset to its original settings,
and the green LED will be solid for 2 seconds
and then remain the colourful gradient status as a
conrmation.
4
repeater the steps above.
AC input:
Version Input (Standby power) Working band
AU 230V 50Hz, Max: 1.8W 921.42MHz
BR 220V 60Hz, Max: 1.8W 921.42MHz
CN 220V 50Hz, Max: 1.8W 868.40MHz
EU 230V 50Hz, Max: 1.8W 868.42MHz
IL 230V 50Hz, Max: 1.8W 916.02MHz
IN 230V 50Hz, Max: 1.8W 865.20MHz
UK 230V 50Hz, Max: 1.8W 868.42MHz
US 120V 60Hz, Max: 0.8W 908.42MHz
Plug Specifications.
5
Warranty.
6
If you are in need of any technical support during or
subsequent to your products’ warranty, please get in
touch with our support team via http://aeotec.com/
support. The Company you bought this product
from has also guaranteed to assist you with any of
your support needs, and you can also contact them
for accordingly.
This guarantee made by the company who you
purchased the product from includes the transfer of
Aeon Labs’ full warranty to that Company. They’ve
guaranteed that they’ll be able to assist you, the
USA Europe Australia
UK India China

Any repairs under this warranty must be conducted
Customer shall indemnify, defend, and hold Aeon
Labs and Aeon Labs' affiliates, shareholders,
directors, officers, employees, contractors,
agents and other representatives harmless from
all demands, claims, actions, causes of action,
proceedings, suits, assessments, losses, damages,
liabilities, settlements, judgments, fines, penalties,
interest, costs and expenses (including fees and
disbursements of counsel) of every kind (i) based
upon personal injury or death or injury to property
to the extent any of the foregoing is proximately
caused either by a defective product (including strict
liability in tort) or by the negligent or willful acts or
omissions of Customer or its officers, employees,
subcontractors or agents, and/or (ii) arising from
or relating to any actual or alleged infringement or
misappropriation of any patent, trademark, mask
work, copyright, trade secret or any actual or alleged
IN NO EVENT SHALL AEON LABS BE LIABLE FOR
ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR
CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF
PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER
OR ANY THIRD PARTY, WHETHER IN AN ACTION IN
CONTRACT, OR TORT, OR OTHERWISE EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS'
LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR
ANY CAUSE OF ACTION ARISING IN CONNECTION
WITH THIS AGREEMENT OR THE SALE OR USE OF
THE PRODUCTS, WHETHER BASED ON NEGLIGENCE,
STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF
AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY
LIMITED TO, AT AEON LABS' OPTION, REPLACEMENT OF,
OR REPAYMENT OF THE PURCHASE PRICE FOR THAT
PORTION OF PRODUCTS WITH RESPECT TO WHICH
DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND
ARISING IN CONNECTION WITH THIS AGREEMENT OR THE
SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED
UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS
FCC NOTICE (for USA)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY
LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE
WHERE DIRECTLY EXPOSED TO WATER.
Reorient or relocate the receiving antenna.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Warning
Certifications (regional):
Z-Wave and Z-Wave Plus are
registered trademarks of Sigma
Designs and its subsidiaries in the
United States and other countries
Version:501012300002-AA www.aeotec.com
Contact your local government for information
regarding the collection systems available.
1.This device may not cause harmful interference,
and
This device must accept any interference received,
including interference that may cause undesired
operation. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
Customer, with all technical support and repair
needs on our behalf.
Aeon Labs warrants to the original purchaser of
Products that for the Warranty Period (as defined
below), the Products will be free from material
defects in materials and workmanship. The foregoing
warranty is subject to the proper installation,
operation and maintenance of the Products in
accordance with installation instructions and the
operating manual supplied to Customer. Warranty
claims must be made by Customer in writing within
thirty (30) days of the manifestation of a problem.
Aeon Labs' sole obligation under the foregoing
warranty is, at Aeon Labs' option, to repair, replace
or correct any such defect that was present at the
time of delivery, or to remove the Products and to
refund the purchase price to Customer.
The "Warranty Period" begins on the date the
Products is delivered and continues for 12 months.
by an authorized Aeon Labs service representative
and under Aeon Labs' RMA policy. Any repairs
conducted by unauthorized persons shall void this
warranty.
Excluded from the warranty are problems
due to accidents, acts of God, civil or military
authority, civil disturbance, war, strikes, res, other
catastrophes, misuse, misapplication, storage
damage, negligence, electrical power problems, or
modication to the Products or its components.
Aeon Labs does not authorize any person or party
to assume or create for it any other obligation or
liability in connection with the Products except as
set forth herein.
Aeon Labs will pass on to Customer all
manufacturers’ Material warranties to the extent
that they are transferable, but will not independently
warrant any Material.
Customer must prepay shipping and transportation
charges for returned Products, and insure the
shipment or accept the risk of loss or damage
FROM AEON LABS'S DELIVERY, OR THE DATE FIXED FOR
DELIVERY IN THE EVENT OF NONDELIVERY.
THE INDEMNITY AND WARRANTY IN ABOVE ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES
OR WARRANTIES, WHETHER EXPRESS OR
IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
during such shipment and transportation. Aeon
Labs will ship the repaired or replacement products
to Customer freight prepaid.
violation of any other intellectual property rights
arising from or in connection with the products,
except to the extent that such infringement exists as
a result of Aeon Labs' manufacturing processes.
2.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC ID: XBAFT118

Association information
The Range Extender 6 supports 1 association group and
can add max 1 node in this group.
The Group 1 is the Lifeline group.
When the Range Extender is reset, the Device Reset Locally
Notofication will be sent to the associated node in
Association Group 1.
Configuration parameters information