AeroAudio MOS Quatro User manual

STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
MOS - QUATRO
MANUAL
The MOS Quatro is a four-way 19 inch microphone onair switch for switching microphone lighting
on for example theYellowtec Mika microphone arms.
The four microphone ports switch separately from each other.
The indication LED’s on the front panel of the MOS Quatro show the status of each microphone.
The status LED indicates whether the microphone arms are on standby, xed white light, or fading in
and out.
Up to 4 microphone arms can be connected to the rear panel of the MOS-Quatro.The MOS-Quatro
will control the lights of the connected arms in red for on-air and white for off-air.
The audio signal is routed directly from the connected microphone arm to a standard 3-pin XLR
connector.

STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
MOS - QUATRO
MANUAL
SUB-D GPI 1-2
GPI connection for microphone 1 and 2
RJ45 GPI 1-2
GPI connection for microphone 1 and 2
Pin Function Signal
1 Microphone 1, +5 to +15 volt GPI
2 Microphone 1, contact to GND GPI
3 Microphone 2, +5 to +15 volt GPI
4 Microphone 2, contact to GND GPI
5 Activate status to GND GPI
6 Microphone 1, voltage GND Ground
7 Microphone 1, contact GND Ground
8 Microphone 2, voltage GND Ground
9 Microphone 2, contact GND Ground
Pin Function Signal
1 Microphone 1, +5 to +15 volt GPI
2 Microphone 1, voltage GND Ground
3 Microphone 1, contact to GND GPI
4 Microphone 1, contact GND Ground
5 Microphone 2, +5 to +15 volt GPI
6 Microphone 2, voltage GND Ground
7 Microphone 2, contact to GND GPI
8 Microphone 2, contact GND Ground
Connections from left to right
Power
9 to 18 volts DC
RJ11
Link connection for synchronisation with other MOS (Uno or Quatro)
Link1 = master and Link2 = slave

STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
MOS - QUATRO
MANUAL
SUB-D GPI 3-4
SUB-D GPI 3-4
RJ45 GPI 3-4
GPI connection for Microphone 1 and 2
Pin Function Signal
1 Microphone 3, +5 to +15 volt GPI
2 Microphone 3, contact to GND GPI
3 Microphone 4, +5 to +15 volt GPI
4 Microphone 4, contact to GND GPI
5
6 Microphone 3, voltage GND Ground
7 Microphone 3, contact GND Ground
8 Microphone 4, voltage GND Ground
9 Microphone 4, contact GND Ground
Pin Function Signal
1 Microphone 3, +5 to +15 volt GPI
2 Microphone 3, voltage GND Ground
3 Microphone 3, contact to GND GPI
4 Microphone 3, contact GND Ground
5 Microphone 4, +5 to +15 volt GPI
6 Microphone 4, voltage GND Ground
7 Microphone 4, contact to GND GPI
8 Microphone 4, contact GND Ground

STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
MOS - QUATRO
MANUAL
XLR 3p male
Microphone 2 output audio signal
XLR 5p female
Microphone arm 3
XLR 3p male
Microphone 3 output audio signal
XLR 5p female
Microphone arm 4
XLR 3p male
Microphone 4 output audio signal
Dimensions
19 inch, 1HE
Depth: 22.2cm
Weight: 2.6kg
XLR 3p male
Microphone 1 output audio signal
XLR 5p female
Microphone arm 1
Pin Function Type
1 Shield Shield
2 Signal + Input
3 Signal - Input
Pin Function Type
1 Shield Shield
2 Signal + Input
3 Signal - Input
4 LED + 12 volt Output
5 Led – 12 volt Output

MOS - QUATRO
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
Safety First!
- Caution: hot and sharp surfaces ! This professional device should only be installed by qualied personnel.
- Check the cardboard box for any damage upon receipt of the goods. In case of a damaged box, please contact your distributor
contact your distributor before opening the box.
- Read all documentation before using the unit.
- Keep all documentation for future use.
- Keep the box and packing materials even if the equipment has arrived in good condition.
- Should you ever need to ship the equipment, use only the original factory packaging.
- Do not spill water or other liquids in or on the unit.
- Always use the power supply provided.
- Make sure the outlets match the power requirements listed on the back of the power supply.
- Do not use the unit if the power cord is frayed or broken.
- Turn off and disconnect the devices from the power supply before making any connections.
- Do not use the unit near heaters, heating vents, radiators, or other devices that produce heat.
- Do not use the unit on a surface or in an environment that may interfere with the normal ow of air around the unit.
If the unit is used in an extremely dusty or smoky environment, the unit should be “dusted” periodically.
- Do not remove the cover. Removing the cover will expose you to potentially dangerous volt voltages.
- In case of malfunction, this unit should only be serviced by qualied service personnel.
- Always follow the instructions of the supplier and manufacturer - Use only manufacturer specied accessories, spare and replacement parts.
- Use the device only for the application the manufacturer intended.