AeroBed R111 User manual

Made in China.
PUMP R111 AU / RDV
INSTRUCTION MANUAL

1
Thank you for purchasing our luxury AeroBed® product. You can expect premium quality, innovation
and durability from every AeroBed®product.
You are about to enjoy the comfort of the AeroBed® product, the finest alternative sleeping
system available anywhere. It is your responsibility to read and always follow the safety, care and
maintenance instructions for your new product. Always instruct and supervise others on the proper
use, maintenance and safety of your bed.
IMPORTANT: Preparation of your bed requires no tools. Use of
tools may damage your bed.
Read, follow and retain this instruction manual for future
reference.
CUSTOMER QUALITY ASSURANCE
AeroBed®has gone to every effort to ensure that your product is of superior quality and meets the
highest standards for convenience comfort and durability. If for any reason your AeroBed®product is
not working properly you will be entitled to a full repair in accordance with the warranty.
WARNINGS AND IMPORTANT SAFETY NOTES
CAREFULLY READ THE INSTRUCTION MANUAL BEFORE USE.
Bed
However, please note that you will be asked to return your product with your proof of
purchase for testing and if a fault cannot be found you will be charged a service fee.
• Adult supervision is required. This is not a lifesaving device.
Do not leave children unattended in or around water.
• Do not use this airbed as a raft or a boat.
• Do not inflate with an air compressor.
• Keep away from fire.
• This product is delivered with a carry bag. Keep it away from
children. Danger of suffocation!
• This bed is not designed for use by children under 3 years of
age. Children under the age of 3 may suffer serious or fatal
injury through suffocation, falling from the bed or becoming
trapped between the bed and a wall or other objects.
• Product is for indoor use only.
• Fill with cold air only.
• Never use a hair dryer to inflate, this could cause melting.
• Do not over inflate.
WARNING

2
Caution: air temperature and weather do affect the air pressure
in inflatable products. In cold weather your airbed will lose some
pressure due to the fact that the air will contract. If this occurs, you
may want to add a little air to improve your airbed’s performance.
However, in hot weather, the air will expand. You must let some air
out to prevent the airbed from failing due to overpressure.
You should avoid exposing your airbed to extreme temperature
(hot or cold).
• Bursting items can cause serious injury.
• Inflate the airbed until most of the wrinkles in the material are
gone and the bed feels firm to the touch.
• Do not let inflatable products come in contact with sharp,
pointed objects that may puncture the plastic material.
• This mattress is not intended for infants or persons with
limited mobility. They may roll off of the mattress and
become entrapped between the mattress and a wall.
• Product is intended for use as an indoor bed only. Do not step
or jump on bed or use as a trampoline. Bed may puncture.
• Place bed in a safe area before use, making sure that there
are no sharp edges, steps, drops, or breakable items nearby.
Use on flat surfaces only. Bed may tip over on
uneven surfaces.
• This bed is made of plastic and therefore may melt or burn
if it comes in contact with any flame or heat source. Do not
place it near or against heaters, open flame or other
hot objects.
• This is not a water toy. Use as a mattress only.

3
Pump
• Adult supervision required for inflation, deflation and
maintenance. Follow all safety instructions to avoid
serious injury.
• This is an electrical product - not a toy. To avoid risk of fire,
burns, injury, and shock, it should not be played with or
placed where small children can reach it. Do not use in or
around water.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not
play with the appliance.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
• Pump is not intended for continuous use. Pump may stop
working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 4 minutes. To
avoid excessive heat build-up in the pump, let it rest for 5
minutes between complete inflation and deflation cycles.
• Do not attempt to repair the pump. Contact the Customer
Service Department for repair or servicing information.
• Avoid splashing the pump with water.
• Never overinflate an inflatable item.
• Unplug product when not in use.
• Do not block air intake during operation; this could damage
the motor.
• Always monitor the pump during use.
WARNING

4
IMPORTANT: THE FIRMNESS OF YOUR AIRBED MAY
DECREASE AFTER YOU INITIALLY INFLATE IT. YOUR AIRBED
IS NOT LEAKING. THIS IS NORMAL AND IS CAUSED BY THE
MATERIAL STRETCHING AFTER THE AIRBED IS INFLATED.
ADD AIR TO MAINTAIN YOUR DESIRED FIRMNESS.
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR
TO INFLATING OR IT MAY CAUSE AIR LEAKS. PRESSURE
CAN VARY DEPENDING ON ROOM TEMPERATURE AND
CONSUMER WEIGHT.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Release Valve is closed. Bed should be stored with valve in the closed
and latched position. If the Quick Release Valve is open, close it by using 2 thumbs to push
cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps
into the valve opening.
3. Remove the AC plug and cord from the plastic bag and shrink wrap.
4. Plug into any standard polarized 240 Volt AC electrical outlet. This
product electrical rating: 230V AC, 50 Hz, 0.8 A.
Note: Because this is an electric device,
ensure your hands are dry when connecting
the cord set to the pump or plugging it into
the wall outlet.
NOTE: ALWAYS FULLY INFLATE THE BED BEFORE
ADJUSTING FIRMNESS LEVEL.
5. Press and hold the UP arrow (Inflate) on the control wand to inflate your bed
to the full (firmest) capacity. Do not over inflate. Once bed has reached desired
firmness, then release the arrow.
6. Lie on your bed and use the Control Wand to adjust the firmness to your
desired level. For firmer bed, press the UP arrow (Inflate). For softer bed, press
the DOWN arrow (Adjust).
INFLATION
This is the closed
position.
Open Quick Release
Valve.
Close valve using 2
thumbs.

5
CLEANING
Bed
We recommend that you do not let the plush surface of your AeroBed®product get wet. Repeated
exposure to water or other liquids may cause damage to the plush surface that will not be covered
by your warranty. Should liquid come in contact with the plush surface, blot liquid dry and use a
damp cloth to remove any stain. Let surface air dry completely.
You may clean the PVC on the sides and bottom of your AeroBed®product with a mild dishwashing
detergent or household cleaner. Do not use strong chemicals or other compounds. Allow your bed to
air dry completely after cleaning and before storing.
Cover / Valance (if included)
Machine wash separately in warm using mild soap or detergent. Tumble dry on LOW HEAT. Remove
immediately after drying.
1. Inspect your AeroBed®product prior to each use.
2. Keep your AeroBed®product away from any sharp objects. Large cuts or snags may not be
repairable and will not be covered by your warranty.
3. When not in use, store your AeroBed®product in its duffle bag, in a clean, dry place out of
extreme temperatures. Product must be at room temperature prior to inflating.
4. Do not store your AeroBed®product folded inside sofa beds or roll-aways. This may cause
damage to your AeroBed®product that will not be covered under your warranty.
5. In case of incidental damage to your bed, a repair kit has been included for some product
models. Please follow repair instructions carefully.
CARE AND MAINTENANCE
Make sure product is completely dry and clean before deflating
and storing.
1. To deflate your AeroBed®product, open the Quick Release
Valve (see figure A).
2. For most compact storage, please close valve, press and
hold the DOWN arrow (Deflate) on the Control Wand until all
the air is expelled from the bed.
3. Roll or fold the AC cord and wand cord and secure it. Fold the
sides of the bed into the center along its length. (see figure B)
Tightly roll and place the bed in the convenient carry bag for
easy transport and storage.
4. Store your bed in a clean, dry place at room temperature
(above 50 °F/10 °C). Storing your bed under 50 °F (10 °C) and
over 100 °F (38 °C) may affect its performance and will not be
covered under warranty.
5. If a mattress cover and/or valance is included with your bed,
it/they may be removed after deflation. Alternatively, you may
store your product with the mattress cover and /or valance on
the bed. Wrinkly may occur.
DEFLATION AND STORAGE
A
B

6
TROUBLESHOOTING
Very rarely, your AeroBed®product may fail to inflate properly. Should this occur, please use the
following check list.
1. If your AeroBed®product doesn’t appear to be inflating:
• Make sure your bed is plugged into an active electrical outlet.
• Push the remote comfort control’s inflate button firmly.
• Make sure the Quick Release Valve is closed and locked
securely.
If the valve is open, close it by using 2 thumbs to push cover
firmly into valve. Be careful to avoid pushing valve cover to the
right or left as it snaps into valve opening.
2. If air leakage occurs:
Carefully inspect the soft round gasket on inside of Quick Release
Valve cover. Make sure there is no dirt or debris, cuts, nicks or
tears to the gasket. If there is dirt or debris; clean and use. If cut,
nicked or torn, call our Customer Service Department.
Carefully inspect the bed for a puncture or tear. If damaged, repair using the repair patch (If
included with your bed). Follow instructions and warnings printed on label.
3. If trouble persists, please phone our Customer Service Department for assistance.
WARRANTY
EXPRESS WARRANTY
Coleman Brands Pty. Ltd. (“Coleman”) warrants that this product will be free from defects in material
and workmanship for the following periods: the pump and valve, two (2) years from the date of
original purchase and the mattress, one (1) year from the date of original retail purchase. Coleman
will, depending on the circumstances, refund, repair or replace this product or any component of the
product found to be defective during the warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is no longer available, replacement may be
made with a similar product of equal or greater value. To the extent permitted by law and subject to
your non-excludable rights under the Australian Consumer Law (Schedule 2 to the Competition and
Consumer Act 2010 (Cth)) and the New Zealand Consumer Guarantees Act, which are not limited to
a one (1) year period, this is your exclusive remedy for any breach of this limited warranty or for any
other claims otherwise relating to this limited warranty.
In Australia, our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure. The benefits provided under this warranty are in addition to and do not affect purchaser’s
statutory rights under the Australian Consumer Law or other rights at law.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Please keep your proof of purchase documentation, such as the original sales
receipt or the relevant credit card statement. Proof of purchase is required to obtain warranty
performance. Coleman dealers, Coleman service centres, or retail stores selling Coleman®products
do not have the right to alter, modify or in any way change the terms and conditions of this warranty.
The warranty is valid only for products that are purchased new and unused in Australia and New
Zealand, from Coleman or Coleman dealers or retailers.

4010046522 (ECN20060957-02)
Warning: Due to our policy of continual product development, the company reserves the right to
alter or modify this product without prior notice.
WARRANTY EXCLUSIONS AND LIMITATIONS
THE AUSTRALIAN CONSUMER LAW PROVIDES CONSUMERS WITH CERTAIN ‘CONSUMER
GUARANTEES’. THESE GUARANTEES APPLY WHERE THE GOODS AND SERVICES COLEMAN
SUPPLIES TO YOU ARE OF A KIND ORDINARILY ACQUIRED FOR PERSONAL, DOMESTIC OR
HOUSEHOLD USE OR COST LESS THAN $40,000, AND IN THE CASE OF GOODS, ARE NOT
RE-SUPPLIED BY YOU. NOTHING IN THIS LIMITED WARRANTY EXCLUDES, RESTRICTS OR
MODIFIES RIGHTS WHICH YOU HAVE UNDER THE AUSTRALIAN CONSUMER LAW IN RESPECT
OF THE CONSUMER GUARANTEES AND ALL OF THE PROVISIONS IN THIS SECTION ARE TO BE
READ SUBJECT TO THE AUSTRALIAN CONSUMER LAW.
This warranty does not cover: (a) normal wear of the product and/or its parts; (b) parts that are not
genuine Coleman®parts, consumables, lost parts and accessories; (c) damage resulting from any of
the following: negligent use or misuse of the product, commercial use of the product, use contrary
to the operating instructions; disassembly, repair or alteration by anyone other than Coleman or
Coleman service centre, the use of a part other than a genuine Coleman®part; or (d) acts of God,
such as fire, flood, hurricanes and tornadoes.
To the extent permitted by the Australian Consumer Law, the Competition and Consumer Regulation
2010 and the New Zealand Consumer Guarantees Act, Coleman’s liability is limited, depending on
the circumstances, to refund, replacement or repair of Coleman®products or components.
For the avoidance of doubt, any and all other warranties or conditions which are not guaranteed by
the Australian Consumer Law, the Competition and Consumer Regulation 2010 and the New Zealand
Consumer Guarantees Act and which are not expressly included in this warranty as additional
warranties or conditions are expressly excluded, including liability for incidental or consequential
damages caused by the breach of any express or implied warranty or condition.
MAKING A WARRANTY CLAIM - RETURN TO COLEMAN FOR REPAIR
Take the product to an authorised Coleman retailer or Coleman service centre as soon as the
warranty claim arises. You may locate the nearest authorised Coleman retailer or Coleman service
centre by visiting www.coleman.com or calling 1800 224 350. Please ensure that you provide a
written description of the problem with the product, together with your contact name, address and
telephone number and proof of purchase.
Subject to the applicable consumer laws in your jurisdiction, you must pay for the costs of
transporting the product, including packaging, freight and insurance costs, to an authorised
Coleman retailer or Coleman service centre for warranty service. If the warranty claim is
substantiated and accepted by Coleman, Coleman will at its cost, repair or replace any product or
parts and return the product to you. Additionally, if the warranty claim is substantiated and accepted
by Coleman, Coleman will reimburse you for the costs of transporting the product to an authorized
Coleman retailer or Coleman service centre. Coleman reserves the right to seek reimbursement for
any costs and expenses incurred for a warranty claim if the product is found to be in good working
order.
Please call or write us with any comments or questions:
Coleman Brands Pty. Ltd.
Unit 5-6, 13 Lord Street,
Botany NSW 2019
Australia
Telephone: [phone]
Email: [email protected]
www.colemanaustralia.com.au