aFe Power 50-70046R User manual

advanced FLOW engineering Momentum GT Cold Air Intake System
Instruction Manual P/N: 50-70046R / 50-70046D_____________________
Make: SUZUKI Model: JIMNY Year: 2019-2020 Engine: L4-1.5L

Page 2
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.
Label
Qty.
Description
Part Number
A1
1
Air Filter (Pro 5R) For 50-70046R
24-91155
A2
1
Air Filter (Pro DRY S) For 50-70046D
21-91155
B
1
Tube, Silicone
05-5070046B1
C
1
Housing, Plastic
05-5070046B2
D
1
Inlet Scoop, Plastic
05-5070046B3
E
1
Coupling, Silicone: 3-3/4"ID x 3"L
05-01509
F
1
Clamp, 032 (1-9/16" -2-1/2")
03-50016
G
2
Clamp, 060 (3-5/16" - 4-1/4")
03-50002
Installation will require the following tools:
8mm & 10mm nut drivers or ratchet and sockets, pliers or flat-head screwdriver
Emissions Disclaimer: This product does not require a CARB EO# (Vehicle does not exist in U.S.)

Page 3
A1/A2
B
E
D
C
F
G

Page 4
Refer to Figure A for Steps 1-2
Step 1: Remove the two screws securing the inlet scoop. Those screws will be reused to secure the aFe
POWER scoop.
Step 2: Remove the screw securing the factory housing to the engine. This screw will be reused to secure
the aFe POWER housing.
REMOVAL
Figure A

Page 5
Refer to Figure B for Steps 3-5
Step 3: Remove the second screw securing the factory housing to the mounting bracket. This screw will also
be reused to secure the aFe POWER housing.
Step 4: Using pliers, unclip the harness from the factory housing.
Step 5: Untighten the clamp securing the factory intake tube to the throttle body.
REMOVAL
Figure B

Page 6
Refer to Figure C for Steps 6-7
Step 6: Disconnect the harness from the temperature sensor on the factory intake tube.
Step 7: Pull the metal tube out of the factory intake tube.
Figure C
REMOVAL

Page 7
Refer to Figure D for Steps 8-9
Step 8: Remove the full factory air intake system as one piece by pulling the factory intake tube off the
throttle body and the factory housing off its grommet.
Step 9: Make sure the grommet under the housing stays in position. This mount will be reused for the aFe
POWER housing.
REMOVAL
Figure D

Page 8
Refer to Figure E for Steps 10-11
Step 10: Transfer the two grommets with metal sleeves from the factory housing to the aFe POWER
Housing.
Step 11: Slide the aFe POWER air filter into the aFe POWER housing and push it in until it locks into place.
Install the clamp on the filter, but do not tighten the clamp at this time.
INSTALL
Figure E

Page 9
Refer to Figure F for Step 12
Step 12: Remove the temperature sensor from the factory tube and install it into the aFe POWER tube.
INSTALL
Figure F

Page 10
Refer to Figure G for Steps 13-14
Step 13: Connect the aFe POWER tube to the filter.
Step 14: Install the smaller clamp on the aFe POWER tube end, and the filter clamp on the filter end but do
not tigthen at this time.
INSTALL
Figure G