aFe Power ST MOMENTUM 50-40007D User manual

®
advanced FLOW engineering Momentum ST Cold Air Intake System
Instruction Manual P/N: 50-40007D / 50-40007R
Make: Chevrolet Model: Camaro Year: 2016-2020 Engine: L4-2.0L Turbo

®
Label Qty. Description Part Number
A1 1 Air Filter (Pro 5R) 24-91105
A2 1 Air Filter (Pro DRY S) 21-91105
B 1 Tube 05-74212B1
C 1 Housing 05-74210B2-T
D 1 Clamp, #048 03-50007
E 1 Coupling, Silicone 05-01380
F 1 Fitting, Vent 03-01339
G 1 Clamp, #044 05-50019
H 2 Screw, M4 03-50491
I 1 Scoop 05-74210B3
Installation will require the following tools:
8mm nut driver, 11mm deep socket & driver, T20 Torx, 20mm wrench or adjustable wrench.
Warranty Information available at https://afepower.com/contact#warranty
Note: Legal in California for use on race vehicles only. The use of this device on vehicles used on public
streets or highways is strictly prohibited in California and others states that have adopted California
emission regulations.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
Page 2
Retain factory parts for future use.

aFepower.com
Page 3
A1/A2
B
C
F
H
E
G
I
D

®
Refer to Figure A for Step 1
Step 1: Disconnect the braided hose 1 from the intake tube. Disconnect the MAF 2 sensor and pull
off the wire harness clip 3 from the intake tube.
REMOVAL
Page 4
1
32
Figure A

Refer to Figure B for Step 2
Step 2: Use an 8mm nut driver to loosen the factory clamp 4 at the turbo. Remove the factory intake
assembly by pulling up to release air box from its mounting grommets.
aFepower.com
Page 5
REMOVAL
4
Figure B

®
Refer to Figure C for Step 3
Step 3: Make sure the mounting grommets 5 are still in the chassis mounting tabs. If they pulled out
and are stuck in the lower half of the air box, remove them from the air box and insert them back
on the chassis mounting tabs.
Figure C
REMOVAL
Page 6
5
5
5

Refer to Figure D for Steps 4-5
Step 4: Using a Torx 20 driver, remove the mass air flow sensor 6 from the upper half of the air box and
install it on the aFe intake tube using the two supplied M4 screws.
Step 5: Install the supplied aluminum vent fitting 7 into the aFe intake tube using a 20mm wrench or
adjustable wrench.
Figure D
INSTALL
aFepower.com
Page 7
7
6
6

®
Refer to Figure E for Steps 6-7
Step 6: Install the supplied air inlet scoop 8 into the aFe air box.
Step 7: Use the provided plug 9 to close additional air inlet if you want to completely seal the air box.
Best performance gain is obtained by having more air flow (no plug).
Figure E
INSTALL
Page 8
9
8

Refer to Figure F for Step 8
Step 8: Slide the aFe filter and clamp into the aFe housing and push it in until it locks into place. Do not
tighten clamp at this time.
Figure F
INSTALL
aFepower.com
Page 9

®
Page 10
®
Refer to Figure G for Step 9
Step 9: Install the housing assembly into the vehicle by pushing down air box pins into the rubber
grommets. Make sure the pins are completely through the mounting grommets.
Figure G
INSTALL