AFi ECR-4-PoE+ User manual

1 1/15/2015 JPK
ECR-4-PoE+ Instruction Manual
Overview
The ECR-4-PoE+ (4 port receiver) operates with the ECT-1-PoE+ (transmitters) to provide Ethernet Extension for up
to 4 channels of 10/100Base-TX over coaxial cable. The ECR-4-PoE+ incorporates an Ethernet switch which
consolidates the input EoC signals to 1 port of 10/100/1000Mbps Ethernet . This equipment is capable of operating
over a coaxial cable distance of up to 800m. This product supports PoC, hence, no dc power is required for the
transmitter side and the connected IP camera (assuming the camera supports Power over Ethernet PoE). This
product is good for retrofitting analogue to IP while maintaining the existing coaxial cable infrastructure.
Physical Description
Front Panel
Rear Panel
Mounting holes

2 1/15/2015 JPK
Installation
There are two mounting holes in each side of the rear panel. Mount the product on wall with appropriate screws.
Then, push left or right, if the equipment fixed vertically, or push down, if equipment fixed horizontally, to make it
fixed tighter. Installation now is completed.
Setup
1. The EoC receiver is a plug-and-play device. Connect an external AC to DC power adaptor (48VDC to 57VDC
output) to the power connector (2 pin terminal block) according to the polarity shown in the Power Connection
section. Then attach the plug into a standard AC outlet. The PWR LED will then be lit.
2. The READY LED will be lit (ON) when the receiver is ready for data transfer.
3. Connect one end of the coaxial cable to a female BNC connector (COAX DATA) on the ECR-4-PoE+ and the
other end to a transmitter (ECT-1-PoE+). If the transmitter and receiver are properly connected and
communicating with each other, the ACT will be lit (ON). The PoC LED will be lit too when the PoC is in use.
4. Connect the Ethernet cable from an NVR or PC or similar equipment to the Ethernet (10/100/1000Base-T) port.
If the cable is properly connected, the corresponding LED (100M or 1000M depending on the Ethernet
connection) at the RJ45 port with be lit. If there is data being transferred, the LED will be blinking.
Interface
RJ-45 Pin Assignment
Pin
Signal Name
1
TP0+
2
TP0-
3
TP1+
4
TP2+
5
TP2-
6
TP1-
7
TP3+
8
TP3-
Power Connection：
Pin
Description
-
+
Power Input
GND
48~57VDC

3 1/15/2015 JPK
Cable Connection
Interface Type
Support Description
Cable Type
RJ45
10Base-T
100Base-TX
1000Base-T
Category 3 or above cable
Category 5 or above cable
Category 5 or above cable
BNC (Female)
Ethernet over Coax Data
RG-59/U or similar
2-pin Terminal Block
Power input (48~57VDC)
2-wire
LED Status
LEDs
Colour
State
Indication
Steady
Power on
PWR
Green
Off
Power off
Flashing
Data transfer within the coaxial cable
ACT
Green
Off
No data transfer within the coaxial cable
Steady
The converter is ready for data transfer
READY
Green
Off
The converter is not ready
Flashing
Detection stage
ON: 1 sec,
OFF: 5 sec
(Repeat)
Un-connected or broken coaxial cable
ON: 2 sec
OFF: 4 sec
(Repeat)
TX is connected with power adaptor (PoC not required)
ON: 3 sec
OFF: 3 sec
(Repeat)
Overload
PoC 1
PoC 2
PoC 3
PoC 4
Green
ON
Power over Coax in use
Steady
Ethernet connection of 10/100Base-TX is established
Flashing
Transmitting or receiving Ethernet data
100M
Green
Off
Neither valid Ethernet connection established nor transmitting or
receiving Ethernet data
Steady
Ethernet connection of 10/100/1000Base-T is established
Flashing
Transmitting or receiving Ethernet data
Ethernet
1000M
Yellow
Off
Neither valid Ethernet connection established nor transmitting or
receiving Ethernet data

4 1/15/2015 JPK
Dimensions (Unit: mm)