AFRISO FloorControl RT01 User manual

AFRISO-EURO-INDEX GmbH
Lindenstr. 20
D-74363 Güglingen
www.afriso.com
Service AFRISO
Tel. [phone]
[email protected]
953.000.0094
FloorControl RT01 D-230
room thermostat
Work on electrical circuits should only be carried out by an authorised electrician.
The mains voltage (AC 230 V AC) can cause serious injury or death.
Do not allow the device to come into contact with water.
Before dismantling the housing, disconnect the wiring box or other controlled device
from the power supply.
Do not make any modications to the device.
The FloorControl RT01 thermostat is a compact device with
a display and built-in temperature sensor that enables precise
temperature setting in a single room or multiple rooms.
The thermostat is supplied with 230 V AC from the wiring box.
The FloorControl RT01 room thermostat is connected to
the FloorControl WB01 D-8-230 underoor heating box to
control the oor heating system.
The FloorControl RT01 D-230 thermostat (Art. No. 86 018) can be connected to the WB01 D-8-230
box (power supply 230 V AC - Art. No. 86 013).
The thermostat’s mounting location must provide protection from the we-
ather. The RT01 thermostat is designed for wall mounting using a standard
Ø60 mm ush-mounted electrical junction box. The thermostat is xed to
the box through the mounting holes (A) in the back of the housing. The
main part of the thermostat should be disconnected from the rear part by
slightly lifting the latch (B) at the bottom. Attach the rear part to the moun-
ting box, then insert the main part and snap it into the rear part.
1
A
B
+
_
N L L1
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
ADT_230V
user 2020-05-12
Zaprojektowanyprzez Sprawdzonyprzez Zatwierdzonyprzez Data
1 / 1
Wydanie Arkusz
Data
80,60
80,60
27,33
14,73
7,00
R
5
,0
R
1
,0
0
7
7
14,5
39
77,10
53,3
60
60
81
81
16
16
10,6
R2

4
8
Display
INSTALLATION AND OPERATION MANUAL 953.011.0094
WARNUNG!
Description of the device
Compatibility with wiring boxes
Wall mounting
Dimensions Electrical connections with
FloorControl WB01 D-8 box
Current room
temperature

2
Operation
Hysteresis - permissible deviation from setpoint temperature. Hysteresis is to prevent
undesirable clocking of the controlled device with small temperature uctuations.
Hysteresis setting is possible in the range of 0.2÷4°C.
Entering the
menu: hold
down “+”
and “-”
Sensor compensation. Compensation should be carried out if the room temperature
measured by the sensor of the RT01 thermostat is signicantly different from the actual
temperature.
Key lock.
Resetting to factory settings.
Switching between heating mode and cooling mode .
Heating mode: lights – when the room needs reheating
is invisible – when the room is warmed up
Cooling mode: ashes – when the room needs to be cooled
is invisible - when the room is chilled
Parameter/part Value/description
General specication
Dimensions (Wx H x D) 81 x 81 x 39 mm
Ambient temperature 5÷50ºC
Temperature setting range 5÷35ºC
Sensor measurement error +/- 0.5ºC
Electrical parameters
Power supply 230 V AC
Load capacity of the contact 1 A/250 V AC
Power consumption max 0.5 W
Permissible cable type 3x0,5 mm2
Technical data
Decommissioning, scrapping
1. Disconnect the power supply from the device.
2. Remove the device.
3. In order to protect the environment, the decommissioned appliance must not be disposed of with
unsorted household waste. The device must be delivered to a suitable disposal point.
RT01 thermostats are made of recyclable materials.
Guarantee
Customer satisfaction
Addresses
The manufacturer gives 36 months guarantee for the device from the date of purchase from AFRISO sp. z o.o..
The guarantee becomes void as a result of arbitrary alterations or installation not in accordance with this installation
and operation manual.
For AFRISO, customer satisfaction is the most important thing. If you have any questions, suggestions or problems with
the product, please contact us.
The addresses of companies representing the AFRISO group worldwide can be found at www.afriso.com.