Afrison 6 Series User manual

*AFRISON TERMS & CONDITIONS
DUE TO ONGOING R&D AFRISON RESERVES THE CATALOGUE AT ITS OWN DISCRETION AND AT ANY TIME
WITHOUT PRIOR NOTICE 1, 2 , 3 OR 5 YEAR WARRANTY (REPLACE OR REPAIR) - PLEASE SEE FULL TERMS AND CONDITIONS AT WWW.AFRISON.CO.ZA - PICTURES
SHOWN ARE FOR ILLUSTRATION PURPOSES ONLY, ACTUAL PRODUCT MAY VARY DUE TO TECHNICAL DEVELOPMENT. E & OE. © 2022 AFRISON LED. ALL RIGHTS RESERVED.
Cederberg Infra-Red LED Flood light
Part number breakdown
Part number: AA BB CC D EEE F G
AA
BBB
CC
D
EEE
FF
FL Flood light
Wattage
S6
-
Series 6
Lens
Voltage
IR
Infra
-
red
12w, 24w
S
-
155
°
x 85
°
W - 60°
M - 30°
12v
220v
Technical information
Operating voltage
IP Rating
Front cover
Operating temperature (°C)
Standards
Mounting hight (m)
100
2
65
VAC
50/60hz
12-24VDC
IP 65
Polycarbonate
Diffused front cover-
Ultra High Impact
-
20 to 40
SANS 60598
2
-
6
Eye safety information
IR Variants (850nm and 940nm)
CAUTION: IR emitted from this product. IEC 62471 Risk Group 2 Classification. Do not stare at the lamp. Avoid exposure
or use appropriate shielding / eye protection.
Operating position Universal
Series 6
24w
A (mm) 120
B (mm) 175
C (mm) 100
Max
projected
area (m°)
0.033
Weight
(kg)
1.6
U- Bracket mounting holes

*AFRISON TERMS & CONDITIONS
DUE TO ONGOING R&D AFRISON RESERVES THE CATALOGUE AT ITS OWN DISCRETION AND AT ANY TIME
WITHOUT PRIOR NOTICE 1, 2 , 3 OR 5 YEAR WARRANTY (REPLACE OR REPAIR) - PLEASE SEE FULL TERMS AND CONDITIONS AT WWW.AFRISON.CO.ZA - PICTURES
SHOWN ARE FOR ILLUSTRATION PURPOSES ONLY, ACTUAL PRODUCT MAY VARY DUE TO TECHNICAL DEVELOPMENT. E & OE. © 2022 AFRISON LED. ALL RIGHTS RESERVED.
Protection Unit
Cederberg Infra-Red
Flood Light
Installation instruction
A qualified electrician must conduct the installation.
Tools required:
- Flat head screwdriver (to open connection box.
- 13 hex spanner (to adjust u-bracket) tools not included
1. To install the Cederberg Infra-Red Flood Lights, special attention needs to be given to the mounting holes on the U-
bracket for alignment.
a. Use correct size (calculated on hight and weight) bolts / Rawle bolts to correspond with your mounting surface.
b. Once U-bracket adjusted to required angle fasten U-bracket bolts. (M8 25N.m)
220VAC VERSION:
2. To connect to the mains 220VAC confirm main power is switched off.
3. The Cederberg Infra-Red Flood Lights require mains voltage of between 100 to 265VAC 50/60 Hz. Connect the mains
cable to the power supply via the 20mm Cable Gland. Always use round cable and not flex or flat cables for sealing
purposes with the Cable Gland. Open the power supply unit by unscrewing the four screws that keep the lid closed.
Connect the corresponding wires, Brown (L), Blue (N), and Yellow/Green (E) in the connector on the power supply.
Always read the label on the power supply to make sure the voltage is correct. When powering the light, the light
should come on immediately.
12 24VDC VERSION:
4. To connect to the mains 12-24VDC confirm power is switched off.
5. The Cederberg Infra-Red Flood Lights require mains voltage of between 12 to 24VDC 50/60. Connect the power cable
to the connector block via the 20mm Cable Gland. Always use round cable and not flex or flat cables for sealing
purposes with the Cable Gland. Open the connection unit by unscrewing the four screws that keep the lid closed.
Connect the corresponding wires, Red (DC +),Black (DC-). Always read the label on the connection unit to make sure
the voltage is correct. When powering the light, the light should come on immediately.
6. Connection diagram:
7. Picture of Protection Unit: