AG Neovo GM678 User manual

Report Number: 030355-D
April 29, 2003
Page 1 of 27
Rev. 00
FCC CLASS B COMPLIANCE REPORT
(DoC)
for
Electromagnetic Emissions
of
LCD Monitor
Trade Name : COMPAL; AG neovo
Model Number : GM678; F-417
Serial Number : N/A
Report Number : 030355-D
Date : April 29, 2003
Prepared for：
Compal Electronics Inc.
No. 581, Jui Kuang Rd., Neihu,
Taipei, (114) Taiwan, R.O.C.
Prepared by：
C&C LABORATORY, CO., LTD.
No. 81-1, 210 Lane, Pa-de 2nd Road, Lu-Chu Hsiang,
Taoyuan, Taiwan, R.O.C.
TEL: [phone]
FAX: [phone]
This report shall not be reproduced, except in full, without the written approval of
C&C LABORATORY, CO., LTD.
The client to claim product certification, approval or endorsement by NVLAP, NIST or any agency
of the federal government must not use this report.

Report Number: 030355-D
April 29, 2003
Page 2
Rev. 00
TABLE OF CONTENTS
1VERIFICATION OF COMPLIANCE.......................................................3
2SYSTEM DESCRIPTION.........................................................................4
3PRODUCT INFORMATION ....................................................................5
4SUPPORT EQUIPMENT..........................................................................6
5MEASUREMENT PROCEDURE ............................................................7
5.1 PRELIMINARY LINE CONDUCTED EMISSION TEST.............................7
5.2 FINAL LINE CONDUCTED EMISSION TEST.............................................8
5.3 PRELIMINARY RADIATED EMISSION TEST ...........................................9
5.4 FINAL RADIATED EMISSION TEST.........................................................10
6SUMMARY DATA...............................................................................11
7TEST FACILITY.....................................................................................14
8TEST EQUIPMENT LIST.......................................................................15
9BLOCK DIAGRAM OF TEST SETUP..................................................16
10 APPENDIX 1 PHOTOGRAPHS
(TEST SETUP OF LINE CONDUCTED EMISSION TEST)................17
11 APPENDIX 2 PHOTOGRAPHS
(TEST SETUP OF RADIATED EMISSION TEST)...............................19
12 APPENDIX 3 PHOTOGRAPHS OF EUT...........................................21
13 APPENDIX 4 LABELING REQUIREMENTS...................................25

Report Number: 030355-D
April 29, 2003
Page 3
Rev. 00
1 VERIFICATION OF COMPLIANCE
Equipment Under Test: LCD Monitor
Trade Name: COMPAL; AG neovo
Model Number: GM678; F-417
Serial Number: N/A
Applicant: Compal Electronics Inc.
No. 581, Jui Kuang Rd., Neihu, Taipei, (114) Taiwan, R.O.C.
Manufacturer: 1.) Compal Electronics Inc.
No. 8, Nan-Tung Rd., Pin-Cheng City, Tao-Yuan Hsien, Taiwan,
R.O.C.
2.) Compal Electronics (China) Co., Ltd.
No. 988, Tung Fen East Rd., Economic & Technical Development Zone
Kunshan, Jiangsun, P.R. China
Type of Test: FCC Class B (DoC)
Measurement Procedure: ANSI C63.4: 2001
File Number: 030355-D
Date of Test: April 24 ~ 25, 2003
Deviation: None
Condition of Test Sample: Normal
Final Result: Pass
Worst Data: See below
Test Item Freq. (MHz) Measured Data Margin (MµC) Remark
Radiated Emission 179.76 27.7 (dB/m) -2.3 dB (± 3.3498 dB)
Conducted Emission 0.150 41.5 (dB) -24.5 dB (± 2.8216 dB)
 The negative sign in Margin cell means under the specific limit.
 This test result traceable to national or international standards.
The above equipment was tested by C&C Laboratory, Co., Ltd. for compliance with the
requirements set forth in the FCC Rules and Regulations Part 15, Subpart B and the measurement
procedure according to ANSI C63.4. This said equipment in the configuration described in this
report shows the maximum emission levels emanating from equipment are within the compliance
requirements.
The test results of this report relate only to the tested sample identified in this report.
Approved by: Reviewed by:
Jonson Lee / EMC Director Susan Su / Section Manager

Report Number: 030355-D
April 29, 2003
Page 4
Rev. 00
2 SYSTEM DESCRIPTION
EUT Test Program:
1. EMI test program was loaded and executed in Windows 98 mode.
2. Data was sent to EUT filling the screen with upper case of “H” patterns.
3. Test program sequentially exercised printer and modem, then sent “H” patterns to them
individually.
4. Repeat 2 to 3. Test program is self-repeating throughout the test.

Report Number: 030355-D
April 29, 2003
Page 5
Rev. 00
3 PRODUCT INFORMATION
Housing Type: Plastic
EUT Power Rating: 100~240VAC, 50 / 60Hz
AC power during Test: 120VAC/ 60Hz
AC Power Cord Type: Unshielded, 1.8m (Detachable)
OSC/Clock Frequencies: 14.318MHz
LCD Panel Manufacturer: Hyundai Model: HT17E12-200
Power Board Manufacturer: COMPAL Model: VP-719
Main Board Manufacturer: COMPAL Model: VL-720
Key Board Manufacturer: COMPAL Model: VK-718
VGA Cable Type: Shielded, 1.8m (Non-detachable) with two cores
I/O Port of EUT
I/O Port Type Q’TY Tested with
1). Video Out Port (VGA) 1 1
Note: The differences between of the two model numbers (list on this report) are identical, just for
marketing purpose only.

Report Number: 030355-D
April 29, 2003
Page 6
Rev. 00
4 SUPPORT EQUIPMENT
No. Equipment Model
# Serial # FCC ID Trade Name Data Cable Power Cord
1. PC EVO D300 6K1BKF83F18F FCC DoC Compaq N/A Unshielded, 1.8m
2. Modem 2400 94-364-176277 DK467GSM24
Computer
Peripherals Shielded, 1.8m Unshielded, 1.8m
3. Printer EPSON STYLUS
C20SX DW4E130540 FCC DoC EPSON Shielded, 1.8m Unshielded, 1.8m
4. PS/2
Keyboard SK-2800C B1C790BCPJCN6L GYUR79SK Compaq Shielded, 1.8m N/A
5. PS/2 Mouse M-CAA43 LZA11750827 FCC DoC Logitech Shielded, 1.8m N/A
Note: All the above equipment/cables were placed in worse case positions to maximize emission
signals during emission test.
Grounding: Grounding was in accordance with the manufacturer’s requirements and conditions for
the intended use.

Report Number: 030355-D
April 29, 2003
Page 7
Rev. 00
5 MEASUREMENT PROCEDURE
5.1 PRELIMINARY LINE CONDUCTED EMISSION TEST
1) The equipment was set up as per the test configuration to simulate typical actual usage per the
user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters
is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the
dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is
placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT
from the ground plane.
2) Support equipment, if needed, was placed as per ANSI C63.4.
3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4.
4) The EUT received AC power through a Line Impedance Stabilization Network (LISN) which
supplied power source and was grounded to the ground plane.
5) All support equipment received power from a second LISN supplying power of 110VAC/60Hz,
if any.
6) The EUT test program was started. Emissions were measured on each current carrying line of
the EUT using a spectrum analyzer / Receiver connected to the LISN powering the EUT. The
LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans
were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50
ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the
Analyzer / Receiver.
7) Analyzer / Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes.
8) During the above scans, the emissions were maximized by cable manipulation.
9) The following test mode(s) were scanned during the preliminary test:
Mode(s):
1. 1280 × 1024 Resolution 75Hz
2. 1024 × 768 Resolution 75Hz
3. 800 × 600 Resolution 75Hz
10) After the preliminary scan, we found the following test mode producing the highest emission
level.
Mode: 1.
Then, the EUT configuration and cable configuration of the above highest emission level were
recorded for reference of final testing.

Report Number: 030355-D
April 29, 2003
Page 8
Rev. 00
5.2 FINAL LINE CONDUCTED EMISSION TEST
1) EUT and support equipment was set up on the test bench as per step 10 of the preliminary test.
2) A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest
emissions. Emission frequency and amplitude were recorded into a computer in which
correction factors were used to calculate the emission level and compare reading to the
applicable limit. If EUT emission level was less –2dB to the A.V. limit in Q.P. mode, then the
emission signal was re-checked using an Average detector.
3) The test data of the worst case condition(s) was reported on the Summary Data page.
Data Sample:
Freq.
MHz
Q.P.
Raw
dBuV
Average
Raw
dBuV
Q.P.
Limit
dBuV
Average
Limit
dBuV
Q.P.
Margin
dB
Average
Margin
dB
Note
x.xx 43.95 --- 56 46 -12.05 -2.05 L 1
Freq. = Emission frequency in MHz
Raw dBuV = Uncorrected Analyzer/Receiver reading +
Insertion loss of LISN, if it > 0.5 dB
Limit dBuV = Limit stated in standard
Margin dB = Reading in reference to limit
Note = Current carrying line of reading
“---“ = The emission level complied with the
Average limits, with at least 2dB margin
limits, so no further recheck.
Calculation example:
Margin (dB) = RAW (dBuV) – Limit (dBuV)
LINE CONDUCTED EMISSION LIMIT
Maximum RF Line Voltage
Frequency Q.P. AVERAGE
150kHz-500kHz 66-56dBuV 56-46dBuV
500kHz-5MHz 56dBuV 46dBuV
5MHz-30MHz 60dBuV 50dBuV
Note: The lower limit shall apply at the transition frequency.

Report Number: 030355-D
April 29, 2003
Page 9
Rev. 00
5.3 PRELIMINARY RADIATED EMISSION TEST
1) The equipment was set up as per the test configuration to simulate typical actual usage per the
user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8
meters is used which is placed on the ground plane as per ANSI C63.4 (see Test Facility for the
dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is
placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT
from the ground plane.
2) Support equipment, if needed, was placed as per ANSI C63.4.
3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4.
4) The EUT received AC power source from the outlet socket under the turntable. All support
equipment received 110VAC/60Hz power from another socket under the turntable, if any.
5) The antenna was placed at 10 meter away from the EUT as stated in ANSI C63.4. The
antenna connected to the Analyzer via a cable and at times a pre-amplifier would be used.
6) The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT test program
was started. Emissions were scanned and measured rotating the EUT to 360 degrees and
positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the
horizontal polarization, to maximize the emission reading level.
7) The following test mode(s) were scanned during the preliminary test:
Mode(s):
1. 1280 × 1024 Resolution 75Hz
2. 1024 × 768 Resolution 75Hz
3. 800 × 600 Resolution 75Hz
8) After the preliminary scan, we found the following test mode producing the highest emission
level.
Model: 1.
Then, the EUT and cable configuration, antenna position, polarization and turntable position of the
above highest emission level were recorded for reference of final testing.

Report Number: 030355-D
April 29, 2003
Page 10
Rev. 00
5.4 FINAL RADIATED EMISSION TEST
1) EUT and support equipment were set up on the turntable as per step 8 of the preliminary test.
2) The Analyzer / Receiver scanned from 30MHz to 1000MHz. Emissions were scanned and
measured rotating the EUT to 360 degrees, varying cable placement and positioning the antenna
1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to
maximize the emission reading level.
3) Recorded at least the six highest emissions. Emission frequency, amplitude, antenna position,
polarization and turntable position were recorded into a computer in which correction factors
were used to calculate the emission level and compare reading to the applicable limit and only
Q.P. reading is presented.
4) The test data of the worst case condition(s) was reported on the Summary Data page.
Data Sample:
======================================================================
Freq. Raw Corr. Emiss. Limits Margin
Data Factor Level
(MHz) (dBuV) (dB) ( dBuV/m ) (dB)
======================================================================
xx.xx 14.0 11.2 26.2 30 -3.8
======================================================================
Freq. = Emission frequency in MHz
Raw Data (dBuV) = Uncorrected Analyzer / Receiver reading
Corr. Factor (dB) = Antenna factor + Cable loss – Amplifier gain
Emiss. Level = Raw reading converted to dBuV/m and CF added
Limit dBuV/m = Limit stated in standard
Margin dB = Reading in reference to limit
P = Peak Reading
Q = Quasi-peak Reading
A = Average Reading
Calculation example:
Margin (dB) = Emiss. Level (dBuV/m) – Limits (dBuV/m)
Emission Level (dBuV/m)=Raw Data (dBuV) + Corr Factor (dB)
RADIATED EMISSION LIMIT
Frequency
(MHz)
Distance
(m)
Maximum Field Strength Limit
(dBu V/m/ Q.P.)
30-230 10 30
230-1000 10 37
Note: The lower limit shall apply at the transition frequency.

Report Number: 030355-D
April 29, 2003
Page 11
Rev. 00
6 SUMMARY DATA
(LINE CONDUCTED TEST)
Model Number: GM678 Location: Site # 4
Tested by: Hank Huang
Test Mode: Mode 1
Test Results: Passed
Temperature: 20°C Humidity: 65%RH
(The chart below shows the highest readings taken from the final data)
FREQ Q.P. AVG Q.P. AVG Q.P. AVG NOTE
MHz RAW RAW Limit Limit Margin Margin
dBuV dBuV dBuV dBuV dB dB
0.150 40.10 --- 66.00 56.00 -25.90 --- L1
1.650 25.40 --- 56.00 46.00 -30.60 --- L1
3.470 27.10 --- 56.00 46.00 -28.90 --- L1
16.080 28.90 --- 60.00 50.00 -31.10 --- L1
18.650 29.10 --- 60.00 50.00 -30.90 --- L1
19.330 28.60 --- 60.00 50.00 -31.40 --- L1
0.150 41.50 --- 66.00 56.00 -24.50 --- L2
0.910 27.20 --- 56.00 46.00 -28.80 --- L2
3.750 24.30 --- 56.00 46.00 -31.70 --- L2
4.150 25.60 --- 56.00 46.00 -30.40 --- L2
15.840 27.30 --- 60.00 50.00 -32.70 --- L2
17.680 30.70 --- 60.00 50.00 -29.30 --- L2
L1 = Line One (Hot side) / L2 = Line Two (Neutral side)
**NOTE: “---” denotes the emission level was or more than 2dB below the Average limit,
so no re-check anymore.

Report Number: 030355-D
April 29, 2003
Page 12
Rev. 00
SUMMARY DATA
(RADIATED EMISSION TEST)
Model Number: GM678 Location: Site # 1
Tested by: Hank Huang Polar: Vertical--10m
Test Mode: Mode 1 Test Results: Passed
Detector Function: Quasi-Peak
Temperature: 21°C Humidity: 65%RH
(The chart below shows the highest readings taken from the final data)
==============================================================
Freq. Raw Corr. Emiss. Limits Margin
Data Factor Level
(MHz) (dBuV) (dB) ( dBuV/m ) (dB)
==============================================================
78.75 15.5 6.8 22.3 30.0 -7.7
---------------------------------------------------------------------------------------------------------
157.29 16.3 10.2 26.5 30.0 -3.5
---------------------------------------------------------------------------------------------------------
168.08 15.1 10.5 25.6 30.0 -4.4
---------------------------------------------------------------------------------------------------------
179.76 16.2 11.5 27.7 30.0 -2.3
---------------------------------------------------------------------------------------------------------
200.80 12.2 10.8 23.0 30.0 -7.0
---------------------------------------------------------------------------------------------------------
315.15 18.1 16.2 34.3 37.0 -2.7
---------------------------------------------------------------------------------------------------------
571.17 7.5 22.3 29.8 37.0 -7.2
---------------------------------------------------------------------------------------------------------
614.42 10.6 22.5 33.1 37.0 -3.9
---------------------------------------------------------------------------------------------------------

Report Number: 030355-D
April 29, 2003
Page 13
Rev. 00
SUMMARY DATA
(RADIATED EMISSION TEST)
Model Number: GM678 Location: Site # 1
Tested by: Hank Huang Polar: Horizontal--10m
Test Mode: Mode 1 Test Results: Passed
Detector Function: Quasi-Peak
Temperature: 21°C Humidity: 65%RH
(The chart below shows the highest readings taken from the final data)
==============================================================
Freq. Raw Corr. Emiss. Limits Margin
Data Factor Level
(MHz) (dBuV) (dB) ( dBuV/m ) (dB)
==============================================================
157.85 12.1 10.1 22.2 30.0 -7.8
--------------------------------------------------------------------------------------------------------
189.54 9.6 11.2 20.8 30.0 -9.2
--------------------------------------------------------------------------------------------------------
215.30 13.4 10.5 23.9 30.0 -6.1
--------------------------------------------------------------------------------------------------------
271.80 11.8 15.9 27.7 37.0 -9.3
--------------------------------------------------------------------------------------------------------
501.60 8.4 21.2 29.6 37.0 -7.4
--------------------------------------------------------------------------------------------------------
577.20 6.2 22.3 28.5 37.0 -8.5
--------------------------------------------------------------------------------------------------------
610.80 10.0 22.4 32.4 37.0 -4.6
--------------------------------------------------------------------------------------------------------
865.60 5.1 28.3 33.4 37.0 -3.6
--------------------------------------------------------------------------------------------------------

Report Number: 030355-D
April 29, 2003
Page 14
Rev. 00
7 TEST FACILITY
Location: No. 81-1, 210 Lane, Pa-de 2nd Road, Lu-Chu Hsiang, Taoyuan,
Taiwan, R. O. C.
Description: There are four 3/10m open area test sites and three line conducted
labs for final test. The Open Area Test Sites and the Line Conducted
labs are constructed and calibrated to meet the FCC requirements in
documents ANSI C63.4: 2001 and CISPR 16 requirements.
Site Filing: A site description is on file with the Federal Communications
Commission, 7435 Oakland Mills Road, Columbia, MD 21046.
Registration also was made with Voluntary Control Council for
Interference (VCCI).
Site Accreditation: Accredited by NEMKO (Authorization #: ELA 124) for EMC &
A2LA (Certificate #: 824.01) for Emission
Accredited by NVLAP (Certificate #: 200600-0)
Also accredited by BSMI for the product category of Information
Technology Equipment.
Instrument Tolerance: All measuring equipment is in accord with ANSI C63.4 and CISPR
22 requirements that meet industry regulatory agency and
accreditation agency requirement.
Ground Plane: Two conductive reference ground planes were used during the Line Conducted
Emission, one in vertical and the other in horizontal. The dimensions of these ground planes are
as below. The vertical ground plane was placed distancing 40 cm to the rear of the wooden test
table on where the EUT and the support equipment were placed during test. The horizontal
ground plane projected 50 cm beyond the footprint of the EUT system and distanced 80 cm to the
wooden test table. For Radiated Emission Test, one horizontal conductive ground plane extended
at least 1m beyond the periphery of the EUT and the largest measuring antenna, and covered the
entire area between the EUT and the antenna. It has no holes or gaps having longitudinal
dimensions larger than one-tenth of a wavelength at the highest frequency of measurement up to
1GHz.
Site # 3 & # 4 Line Conducted Test Site: At Shielding Room

Report Number: 030355-D
April 29, 2003
Page 15
Rev. 00
8 TEST EQUIPMENT LIST
Instrumentation: The following list contains equipment used at C & C Laboratory, Co., Ltd. for
testing. The equipment conforms to the CISPR 16-1 / ANSI C63.2-1988 Specifications for
Electromagnetic Interference and Field Strength Instrumentation from 9kHz to 1.0 GHz or above.
Equipment used during the tests:
Open Area Test Site: # 1
Open Area Test Site # 1
EQUIPMENT
TYPE MFR MODEL
NUMBER SERIAL NUMBER LAST CAL. CAL. DUE
Spectrum Analyzer HP 8568B 3001A05004 07/03/2002 07/02/2003
S.P.A Display HP 85662A 3014A18846 07/03/2002 07/02/2003
Q.P Adaptor HP 85650A 2811A01399 07/03/2002 07/02/2003
RF Pre-selector HP 85685A 2947A01064 07/03/2002 07/02/2003
Spectrum Analyzer Anritsu MS2601A MT09950 N/A N/A
Pre-Amplifier HP 8447D 2944A08432 N/A N/A
Bilog Antenna CHASE CBL6112A 2309 02/28/2003 02/27/2004
Turn Table EMCO 2081-1.21 N/A N.C.R N.C.R
Antenna Tower EMCO 2075-2 9707-2604 N.C.R N.C.R
Controller EMCO 2090 N/A N.C.R N.C.R
RF Switch ANRITSU MP59B M54367 N.C.R N.C.R
Site NSA C&C N/A N/A 08/31/2002 08/30/2003
Conducted Emission Test Site: # 4
Conducted Emission Test Site # 4
EQUIPMENT
TYPE MFR MODEL
NUMBER SERIAL NUMBER LAST CAL. CAL. DUE
EMI Test Receiver R&S ESHS30 828144/003 08/08/2002 08/07/2003
LISN R&S ENV 4200 830326/016 03/05/2003 03/04/2004
LISN EMCO 3825/2 9003/1382 02/26/2003 02/25/2004
The calibrations of the measuring instruments, including any accessories that may effect such
calibration, are checked frequently to assure their accuracy. Adjustments are made and correction
factors applied in accordance with instructions contained in the manual for the measuring
instrument.

Report Number: 030355-D
April 29, 2003
Page 16
Rev. 00
9 BLOCK DIAGRAM OF TEST SETUP
SYSTEM DIAGRAM OF CONNECTIONS BETWEEN EUT AND SIMULATORS
EUT: LCD Monitor
Trade Name: COMPAL
Model Number: GM678
Power Cord: Unshielded, 1.8m
2. Modem
3. Printer
5. PS/2 Mouse
1. PC
LCD Monitor
(EUT)
4. PS/2 Keyboard
VGA Cable

Report Number: 030355-D
April 29, 2003
Page 17
Rev. 00
10 APPENDIX1 PHOTOGRAPHS
(TEST SETUP OF LINE CONDUCTED EMISSION TEST)

Report Number: 030355-D
April 29, 2003
Page 18
Rev. 00
LINE CONDUCTED EMISSION TEST
Front View
Back View

Report Number: 030355-D
April 29, 2003
Page 19
Rev. 00
11 APPENDIX2 PHOTOGRAPHS
(TEST SETUP OF RADIATED EMISSION TEST)

Report Number: 030355-D
April 29, 2003
Page 20
Rev. 00
RADIATED EMISSION TEST
Front View
Back View