AG Neovo DS-55 User manual

TABLE OF CONTENTS
Important Safety Instructions ..................................................................1
1.1 Safety precautions and maintenance…………………….…............1
1.2 Use…………………………………………………………..…..……...4
1.3 Installation Notes……………………………………………..…..…...7
Package Content .......................................................................................9
2.1 Unpacking………………………………………………….…………..9
2.2 Accessories……………………………….…………….………..…..10
2.3 Overview……………………………………………………..……….11
Setting Up the Display ...........................................................................13
3.1 Step 1 : Putting the dual-sided display upside …………..………13
3.2 Step 2 : Remove the three I/O covers on the sides ……………..14
3.3 Step 3 : Remove the downside cover …………………..…….…..15
3.4 Step 4 : Link power box to dual side display …………..………...16
3.5 Step 5 : Connect by HDMI connector ………………………….…18
3.6 Step 6 : Reinstall the downside cover and I/O covers …….…….19
3.7 Step 7 : Connect the power cord………........................................20
3.8 Step 8 : Using the Remote Control ………………………………..21
3.9 OSD Setting Menu…………………………………………..………22
Trouble shooting ....................................................................................26
Specifications .........................................................................................27
Product Dimensions ..............................................................................28

1.1 Safety precautions and maintenance
WARNING:
Use of control, adjustments or procedures other than those
specified in this documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and
using your display:
Operation:
•Keep the display out of direct sunlight and away from stoves or any other
heat sources.
•Remove any object that could fall into ventilation holes of power box or
prevent proper cooling of the display’s electronics.
•Don’t block the ventilation holes on the power box.
•When positioning the display, make sure the power plug and outlet are
easily accessible.
•When turning off the display by detaching the power cord, wait 6 seconds
before re-attaching the power cord for normal operation.
•Ensure the use of an approved power cord provided byAUO at all times.
If your power cord is missing, please contact your local service center.
•Don’t subject the display to severe vibration or high impact conditions
during operation.
•Don’t knock or drop the display during operation or transportation.
•Provide an earthing connection before the mains plug is connected to the
mains.And, when disconnecting the earthing connection, be sure to
disconnect after pulling out the mains plug from the mains.
Important Safety Instructions
1

Maintenance:
•To protect your display from possible damage, do not put excessive
pressure on the display.
•Unplug the display if you are not going to use it for an extensive period of
time.
•Unplug the display if you need to clean it with a slightly damp cloth. The
screen may be wiped with a dry cloth when the power is off. However,
never use organic solvent, such as, alcohol, or ammonia-based liquids to
clean your display.
•To avoid the risk of shock or permanent damage to the set, do not
expose the display to dust, rain, water or an excessively moist
environment.
•If your display becomes wet, wipe it with dry cloth as soon as possible.
•If a foreign substance or water gets in your display, turn the power off
immediately and disconnect the power cord. Then remove the foreign
substance or water.
•Don’t store or use the display in locations exposed to heat, direct sunlight
or extreme cold.
Important Safety Instructions
2

Read and follow these instructions when connecting and using your
display:
•Unplug the display if you are not going to use it for an extensive period of
time.
•Unplug the display if you need to clean it with a slightly damp cloth. The
screen may be wiped with a dry cloth when the power is
off. However, never use alcohol, solvents or ammonia-based liquids.
•Keep the display out of direct sunlight and away from stoves or any other
heat sources.
•Remove any object that could fall into the vents or prevent proper cooling
of the display’s electronics.
•Don’t block the ventilation holes on the power box.
•Keep the display dry. To avoid electric shock, do not expose it to rain or
excessive moisture.
•When turning off the display by detaching the power cable or DC power
cord, wait for 6 seconds before re-attaching the power
cable or DC power cord for normal operation.
•When positioning the display, make sure the power plug and outlet are
easily accessible.
•Consult a service technician if the display does not operate normally after
having followed the instructions in this manual.
Important Safety Instructions
3

•Don’t turn the ventilation hole of Power Box upside down.
As shown in the picture below.
The ventilation hole of
power box
It is prohibited to
place tilt
The ventilation hole of
power box
It is prohibited to turn the
ventilation hole of Power
Box upside down.
Important Safety Instructions
1.2 Use
4

•When you install the display, please don’t use the
“bottom side” I/O hole and open the I/O cover . As shown
in the picture below.
The “bottom side” I/O cover
can’t be opened.
Important Safety Instructions
5

Disconnect devices:
•For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
Remote Controller Precautions:
•This product requires remote switch (ON/OFF) from Front Side ; the
Back Side only has OSD function operated by remote controller.
The Front Side have a product label.
Front Side (450 nits) Back Side (450 nits)
Important Safety Instructions
6

There have 8 use holes on the side of the
display set (M4x15mm)
F
Important Safety Instructions
1.3 Installation Notes
7

Please make sure you
have a solid installation.
As shown in the picture.
You can install the display
set by screws x 8
(M4x15mm)
Important Safety Instructions
8

•This product is packed in a carton, together with the standard
accessories.
•Due to the size and weight of this display it is recommended for two
people to move it.
•After opening the carton, ensure that the contents are complete and in
good condition.
Package Content
2.1 Unpacking
9
DS-55 DUAL SET

Dual Side Display x1
Power Cord x1
PC Box x1
(with 24V&12V line)
Remote Controller x1
(Battery : CR 2025 3V)
Package Content
2.2 Accessories
10

Front View
Top View
Diagonal View
Side View
Package Content
2.3 Over View
11

1. Display (Dual-sided)
2. Display Set
3. Remote control sensor (Dual-sided)
4. Use hole x 8 (single side have 4)
5. I/O cover x 3
1
2
4
5
3
Package Content
12

While the display put
upside , the screw will
be seen on the left.
Setting Up The Display
3.1 Step 1 : Putting the dual-sided display upside
13

Remove I/O cover
screws x 3 (M3x6mm)
Setting Up The Display
3.2 Step 2 : Remove the three I/O covers on the
sides
14

Tear down the
downside cover.
screws x 10 (M3x6mm)
Setting Up The Display
3.3 Step 3 : Remove the downside cover
15

Power Box
Dual Side
Display
24V*1
Red line
(10 pin)
12V*1
Yellow line
(8 pin)
1
2
Setting Up The Display
3.4 Step 4 : Connect Power Box to Dual Side
Display
16

Connect the 24V (10 pin) power line
1 Connect the 12V (8 pin) power line
12V*1
Yellow line
(8 pin)
24V*1
Red line
(10 pin)
2
1
2
Setting Up The Display
17

Plug two HDMI cables into the cabinet.
And ensure that all cable plugs are firmly fitted to
the equipment jacks.
HDMI HDMI
Front Side (450 nits) Back Side (450 nits)
Setting Up The Display
3.5 Step 5 : Connect by HDMI connector
18