AG Neovo MD-2402 User manual

MD-2402 & MD-2702 LCD Monitor
User Manual
www.agneovo.com

TABLE OF CONTENTS
2
SAFETY INFORMATION
WEEE...........................................................................................................................................................4
PRECAUTIONS
Notice ...........................................................................................................................................................5
Cautions When Setting Up ........................................................................................................................... 5
Cautions When Using...................................................................................................................................6
Cleaning and Maintenance........................................................................................................................... 7
Notice for the LCD Monitor........................................................................................................................... 7
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents ..................................................................................................................................8
1.2 Installation ..............................................................................................................................................9
1.2.1 Installing the Stand...................................................................................................................... 9
1.2.2 Adjusting the Viewing Angle and Height....................................................................................10
1.2.3 Wall Mounting............................................................................................................................ 11
1.3 Overview ..............................................................................................................................................12
1.3.1 Control Panel and Indicator....................................................................................................... 12
1.3.2 Rear View..................................................................................................................................13
CHAPTER 2: MAKING CONNECTIONS
2.1 Connecting the AC Power .................................................................................................................... 14
2.2 Connecting Input Source Signals ......................................................................................................... 15
CHAPTER 3: USING THE LCD MONITOR
3.1 Turning on the Power ........................................................................................................................... 16
3.2 Selecting a Source ............................................................................................................................... 16
3.3 Using Auto Adjustment Function .......................................................................................................... 17
3.4 Selecting the Picture Mode .................................................................................................................. 17
3.5 Displaying the OSD Menu .................................................................................................................... 18
3.6 Locking the OSD Menu ........................................................................................................................ 18
CHAPTER 4: ON SCREEN DISPLAY MENU
4.1 Using the OSD Menu ........................................................................................................................... 20
4.2 OSD Menu Tree ...................................................................................................................................21
CHAPTER 5: ADJUSTING THE LCD MONITOR
5.1 Brightness Setting ................................................................................................................................ 22
5.2 Image Setup Setting.............................................................................................................................24
5.3 Colour Temperature Setting ................................................................................................................. 25
5.4 OSD Setting .........................................................................................................................................26
5.5 System Setting .....................................................................................................................................27
CHAPTER 6: APPENDIX
6.1 Warning Messages...............................................................................................................................28
6.2 Timing...................................................................................................................................................29
6.3 Troubleshooting....................................................................................................................................30
6.4 Transporting the LCD Monitor .............................................................................................................. 31
Contents

3
TABLE OF CONTENTS
CHAPTER 7: SPECIFICATIONS
7.1 Monitor Specications .......................................................................................................................... 33
7.2 Monitor Dimensions.............................................................................................................................. 34
7.2.1 MD-2402 Dimensions................................................................................................................34
7.2.2 MD-2702 Dimensions................................................................................................................35

SAFETY INFORMATION
4
Safety Information
WEEE
Information for users applicable in European Union countries
The symbol on the product or its packaging signies that this product has to be disposed
separately from ordinary household wastes at its end of life. Please kindly be aware that
this is your responsibility to dispose electronic equipment at recycling centers so as to
help conserve natural resources. Each country in the European Union should have its
collection centers for electrical and electronic equipment recycling. For information about
your recycling drop off area, please contact your local related electrical and electronic
equipment waste management authority or the retailer where you bought the product.

5
PRECAUTIONS
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD monitor and keep it for future reference.
• The product specications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD monitor. Doing so may
affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LCD monitor near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD monitor on a stable area. Do not place the LCD monitor where it may subject to
vibration or shock.
Place the LCD monitor in a well-ventilated area.
Do not place the LCD monitor outdoors.
Do not place the LCD monitor in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD monitor through the ventilation holes.
Doing so may cause accidental re, electric shock or damage the LCD monitor.
Precautions

6
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD monitor.
The power outlet should be installed near the LCD monitor and be easily accessible.
If an extension cord is used with the LCD monitor, ensure that the total current consumption
plugged into the power outlet does not exceed the ampere rating.
Do not allow anything to rest on the power cord. Do not place the LCD monitor where the
power cord may be stepped on.
If the LCD monitor will not be used for an indenite period of time, unplug the power cord from
the power outlet.
To disconnect the power cord, grasp and pull by the plug head. Do not tug on the cord; doing
so may cause re or electric shock.
Do not unplug or touch the power cord with wet hands.
WARNING:
Unplug the power cord from the power outlet and refer to qualied service personnel under
the following conditions:
• When the power cord is damaged.
• If the LCD monitor has been dropped or the housing has been damaged.
• If the LCD monitor emits smoke or a distinct odor.
Ceiling mount or mount on any other horizontal surface overhead are not advisable.
WARNING:
Installation in contravention of the instructions may result in undesirable consequences,
particularly hurting people and damaging property. Users who have already mounted the
monitor on the ceiling or any other horizontal surface overhead are strongly advised to
contact AG Neovo for consultations and solutions to help ensure a most pleasurable and
fullling monitor experience.

7
PRECAUTIONS
Cleaning and Maintenance
Do not attempt to service the LCD monitor yourself, refer to qualied service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LCD Monitor
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD monitor may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
monitor. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD monitor to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• Adjust the LCD monitor to low brightness settings.
• Turn off the LCD monitor when the system is not in use.
Things to do when the LCD monitor shows image retention:
• Turn off the LCD monitor for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
There are millions of micro transistors inside the LCD monitor. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

CHAPTER 1: PRODUCT DESCRIPTION
8
Chapter 1: Product Description
1.1 Package Contents
When unpacking, check if the following items are included in
the package. If any of them is missing or damaged, contact your
dealer.
Quick Start Guide
Power Cord
Note:
♦The pictures are for reference
only. Actual items may vary
upon shipment.
HDMI Cable
Power Adapter
LCD Monitor
Note:
Must use only the supplied power
adapter:
♦Adaptor Technology
Model no.: ATM065T-P120
Rating: 12V/5A
MD-2402/MD-2702_Quick Guide_V010
Quick Start Guide
MD-2402 & MD-2702 LCD Monitor
www.agneovo.com
MD-2402 MD-2702
Warranty Card
Stand and Screws
(M4 x 10 mm) *4pcs

9
PRODUCT DESCRIPTION
1.2 Installation
1.2.1 Installing the Stand
1. Place the LCD monitor with the screen side down on a cushioned surface.
2. Attach the stand to the LCD monitor.
a. Align and attach the stand to the rear of the LCD monitor.
b. Use the screws to secure the stand.
3. Set the LCD monitor up in an upright position.

10
PRODUCT DESCRIPTION
1.2.2 Adjusting the Viewing Angle and Height
For optimal viewing, it is recommended to look at the full face of the screen, then adjust the screen of the LCD monitor
angle and height according to your preference.
Hold the stand so that the screen does not topple when you make the adjustment.
You are able to adjust the screen angle and height as below:
Tilt angle: Pivot angle:
-5° to 23°
90°
Note: Before making the adjustment, make sure to
adjust the height to the highest position, and then
tilt the screen 90˚.
Swivel angle: Height adjustment:
±65°
11 cm

11
PRODUCT DESCRIPTION
1.2.3 Wall Mounting
To wall mount the LCD monitor, do the following steps:
1. Remove the stand.
Refer to page 31.
2. Wall mount the LCD monitor.
Screw the mounting bracket to the VESA holes at the rear of the LCD monitor.
100 mm
100
mm
DP HDMI VGA
DP HDMI VGA
100 mm
100
mm
MD-2402 MD-2702
Note: Take measures to prevent the LCD monitor from falling down and lessen possible injury and damage
to the monitor in case of earthquakes or other disasters.
• Use only the 100 x 100 mm wall mount kit recommended by AG Neovo. All
AG Neovo wall mount kits comply with VESA standard.
• Secure the LCD monitor on a solid wall strong enough to bear its weight.
• It is suggested to wall mount the LCD monitor without tilting it facing
downward.

12
PRODUCT DESCRIPTION
1.3 Overview
1.3.1 Control Panel and Indicator
MD-2402 MD-2702
1
2
3
4
5
6
1
2
3
4
5
6
1AUTO/SOURCE/EXIT ( ): Hot Key: Source Key
• When OSD menu is OFF, press and hold the keypad keys listed below for at least 3 seconds
to activate the Auto Adjustment function (for VGA input signal source).
• When OSD menu is OFF, press to select input when connecting input cable.
• When OSD menu is ON, press to exit the OSD menu.
2UP ( ):
When the OSD is ON, navigate through adjustment icons or adjust a function.
3DOWN ( ): Hot Key: PICTURE MODE Select
• When OSD menu is OFF, activate the PICTURE MODE Select.
• When OSD menu is ON, navigate through adjustment icons or adjust a function.
4MENU/ENTER ( ):
Active OSD menu, function adjust conrm, or Exit OSD menu.
5POWER ( ):
Press to switch the display on or off.
6Power status indicator: Indicates the operating status of the monitor:
• Blue – Power On mode.
• Blinking Blue – Standby mode.
• LED off – Off mode.

13
PRODUCT DESCRIPTION
1.3.2 Rear View
DP HDMI VGA DP HDMI VGA
DP HDMI VGADC IN
MD-2402 MD-2702
1 2 3 4
1DC IN:
Connect with the supplied power adaptor.
2DisplayPort IN:
Connect DisplayPort signals input.
3HDMI IN:
Connect HDMI signals input.
4VGA IN:
Connect VGA signals input.

CHAPTER 2: MAKING CONNECTIONS
14
CAUTION:
Make sure that the LCD monitor is not connected to the power outlet before making any
connections. Connecting cables while the power is ON may cause possible electric shock or
personal injury.
2.1 Connecting the AC Power
1. Connect the power cord to the power adapter.
2. Connect the power adapter to the DC power input at the rear of the LCD monitor.
3. Connect the power cord plug to a power outlet or a power supply.
DC IN
CAUTION:
When unplugging the power cord, hold the power cord by the plug head. Never pull by the cord.
Chapter 2: Making Connections

15
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
Input source signals can be connected with the following cables:
DP HDMI VGA
DP HDMI VGA
• DisplayPort
Connect one end of a DP cable to the DP connector of the LCD
monitor and the other end to the DP connector of the computer.
• HDMI
Connect one end of an HDMI cable to the HDMI connector of
the LCD monitor and the other end to the HDMI connector of the
computer.
• VGA
Connect one end of a D-Sub (VGA) cable to the D-Sub (VGA)
connector of the LCD monitor and the other end to the D-Sub
(VGA) connector of the computer.

CHAPTER 3: USING THE LCD MONITOR
16
3.1 Turning on the Power
1. Connect the power adapter to the DC power input at the rear of the LCD monitor.
2. Connect the power cord plug to a power outlet or a power supply.
3. Press the key on the control panel.
Power Key
When the LCD monitor is turned on, press the key to turn off the LCD monitor.
Note: The LCD monitor still consumes power as long as the power cord is connected to the power outlet.
Disconnect the power adapter to completely cut off power.
3.2 Selecting a Source
Press the key to call out the source selection menu.
VGA
HDMI
DisplayPort
Source Key
The following menu appears on the screen:
VGA
HDMI
DisplayPort
Chapter 3: Using the LCD Monitor

17
USING THE LCD MONITOR
3.3 Using Auto Adjustment Function
Press and hold the key for at least 3 seconds to perform the auto adjustment for the VGA source. This
function automatically tunes the LCD monitor to its optimal setting, including horizontal position, vertical
position, clock, and phase.
Auto Configure
Please Wait
AUTO Key
When the auto adjustment is initiated, the below message is displayed on the screen:
Auto Configure
Please Wait
3.4 Selecting the Picture Mode
Press the key to call out the picture mode menu.
Picture Mode Standard
Down Key
The following menu appears on the screen:
Picture Mode Standard
Press the or key to select the picture mode. Then press the key to conrm or wait until the picture
mode menu disappears from the screen automatically. The available picture mode options include “Standard”,
and “DICOM”.

18
USING THE LCD MONITOR
3.5 Displaying the OSD Menu
Press the key to open the OSD menu. Press the key to close the OSD menu.
For more information on adjusting settings, refer to page 22.
Brightness
Contrast 50
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
AUTO :Exit MENU :Select:Move
Menu Key
The following menu appears on the screen:
Brightness
Contrast 50
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
AUTO :Exit MENU :Select:Move
3.6 Locking the OSD Menu
To lock the OSD menu, press and hold the key while the LCD monitor is off, and then press the key to
turn the LCD monitor on.
OSD Locked
Menu Key
Power Key

19
USING THE LCD MONITOR
The following menu appears on the screen when you press the , , or key:
OSD Locked
To unlock the OSD menu, press and hold the key while the LCD monitor is off, and then press the key.

CHAPTER 4: ON SCREEN DISPLAY MENU
20
4.1 Using the OSD Menu
1. Press the key to call out the OSD window.
Menu
option
Brightness
Contrast 50
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
AUTO :Exit MENU :Select:Move
Submenu
Main
menu
2. Press the or key to select a menu and press the key to enter the selected menu.
Brightness
Contrast 50
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
AUTO :Exit MENU :Select:Move
Contrast 50
AUTO :Exit MENU :Select:Move
Brightness
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
The selected menu icon appears on the left panel and the text of the selected menu option turns orange.
3. Press the or key to select a submenu item and press the key to enter its options.
Contrast 50
AUTO :Exit MENU :Select:Move
Brightness
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
Contrast 50
Brightness
Brightness 40
Picture Mode Standard
DCR Off
Overdrive Off
AUTO :Exit MENU :Select:Move
The text of the selected menu option or submenu turns orange.
4. Press the or key to adjust the value or select the setting.
5. To exit the submenu, press the key.
6. To close the OSD window, press the key repeatedly.
Note: When settings are modied, all changes are saved when the user does the following:
• Proceeds to another menu
• Exits the OSD menu
• Waits for the OSD menu to disappear
Chapter 4: On Screen Display Menu