AG Neovo RX-22G User manual

RX-22G & RX-24G LCD Monitor
User Manual
displays.agneovo.com

TABLE OF CONTENTS
2
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)............................................................4
W EEE.......................................................................................................................................................5
P recautions
Notice.......................................................................................................................................................6
Cautions W hen Setting Up.......................................................................................................................6
Cautions W hen Using...............................................................................................................................7
Cleaning and Maintenance.......................................................................................................................7
Notice for the LCD Display.......................................................................................................................8
Ch ap ter 1 : P roduct D escrip tion
1.1 Packa ge Contents..............................................................................................................................9
1.2 W all Mounting Installation Preparation...............................................................................................10
1.2.1 W all Mounting..........................................................................................................................10
1.2.2 Removing the Base Stand.......................................................................................................11
1.3 LCD Display Overview .......................................................................................................................12
1.3 .1 Front View and K eypad Buttons..............................................................................................12
1.3 .2 Rear View................................................................................................................................13
Ch ap ter 2 : M ak ing Connections
2.1 Connecting the Power........................................................................................................................14
2.2 Connecting Input Source Signals.......................................................................................................15
2.2.1 Connecting a Computer ..........................................................................................................15
Using VGA Cables ......................................................................................................................... 15
Using DVI Cables...........................................................................................................................15
Using HDMI Cables........................................................................................................................16
Using DisplayPort Cables ..............................................................................................................16
Using RS23 2 Cables......................................................................................................................17
Using Audio Cables........................................................................................................................17
2.2.2 Connecting a Video Device.....................................................................................................18
Using Composite (CVBS) Cables ..................................................................................................18
Using S-Video Cables....................................................................................................................19
Using HDMI Cables........................................................................................................................19
Using DisplayPort Cables ..............................................................................................................20
Ch ap ter 3 : Using th e L CD D isp lay
3 .1 Turning on the Power.........................................................................................................................21
3 .2 Selecting the Input Source Signal......................................................................................................21
3 .3 Adjusting the Volume..........................................................................................................................22
3 .3 .1 Muting the Audio......................................................................................................................22
3 .4 Choosing Y our Preferred Picture Settings.......................................................................................... 22
3 .5 Using Picture-in-Picture (PIP) ............................................................................................................23
3 .5.1 PIP/PBP Options.....................................................................................................................23
3 .5.2 PIP/PBP Swap ........................................................................................................................24
3 .6 Using FREEZ E Function....................................................................................................................24

3
TABLE OF CONTENTS
3 .7 Using Auto Adjustment Function ........................................................................................................25
3 .8 Using ROTATE Function ....................................................................................................................25
3 .9 Locki ng the OSD Menu......................................................................................................................26
Ch ap ter 4: On Screen D isp lay M enu
4 .1 Using the OSD Menu .........................................................................................................................27
4 .2 OSD Menu Tree .................................................................................................................................29
Ch ap ter 5: A dj usting th e L CD D isp lay
5.1 Brightness ..........................................................................................................................................3 2
5.2 Colour Temp.......................................................................................................................................3 4
5.3 Image Setting.....................................................................................................................................3 5
5.4 Aspect Ratio.......................................................................................................................................3 8
5.5 PIP Setting .........................................................................................................................................3 9
5.6 Anti-Burn-in.........................................................................................................................................4 1
5.7 OSD Setting .......................................................................................................................................4 2
5.8 Audio Setting......................................................................................................................................4 3
5.9 System 1 ............................................................................................................................................4 4
5.10 System 2 ..........................................................................................................................................4 6
5.11 EcoSmart Sensor .............................................................................................................................4 8
5.12 Input Select ......................................................................................................................................50
Ch ap ter 6 : A p p endix
6 .1 W arning Messages.............................................................................................................................51
6 .2 Supported Resolutions.......................................................................................................................52
6 .3 Troubleshooting..................................................................................................................................53
6 .4 Transporting the LCD Display ............................................................................................................55

 isplay pecications ........................................................................................................................57
7 .2 Display Dimensions............................................................................................................................58
7 .2.1 RX -22G Dimensions................................................................................................................58
7 .2.2 RX -24 G Dimensions................................................................................................................58

SAFETY INFORMATION
4
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer
device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive
moisture.
THIS CLASS B DIGITALAPPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

5
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.

PRECAUTIONS
6
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symb ols used in th is manual
This icon indicates the existence of a potential haza rd that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD display and ke ep it for future reference.
•The product specifications and other information provided in this ser anual are for reference only ll
information is subject to change without notice. Updated content can be downloaded from our web site at
disp lays.ag neov o.com.
• To protect your rights as a consumer, do not remove any sticke rs from the LCD display. Doing so may
affect the determination of the warranty period.
Cautions Wh en Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
oing so may cause accidental re, electric shock or damage the C display
P recautions

7
PRECAUTIONS
Cautions Wh en Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
display and be easily accessible.
If an extension cord is used with the LCD display,
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
may be stepped on.
f the C display will not be used for an indenite
period of time, unplug the power cord from the
power outlet.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
cause re or electric shock
Do not unplug or touch the power cord with wet
hands.
Cleaning and M aintenance
The LCD display comes with NeoVTM Optical
Glass. Use a soft cloth lightly moistened with a mild
detergent solution to clean the glass surface and the
housing.
Do not rub or tap the surface of the glass with sharp
or abrasive items such as a pen or screwdriver. This
may result in scratching the surface of the glass.
Do not attempt to service the LCD display yourself,
refer to qualied service personnel pening or
removing the covers may expose you to dangerous
voltage or other risks.
Warning :
Unplug the power cord
from the power outlet and
refer to qualied service
personnel under the following
conditions:
♦W hen the power cord is
damaged.
♦If the LCD display has been
dropped or the housing has
been damaged.
♦If the LCD display emits smoke
or a distinct odor.
Warning :
Ceiling mount or mount
on any other horizo ntal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
 eovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

8
PRECAUTIONS
Notice for th e L CD D isp lay
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
W hen static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch deskt op backg rounds regularly.
• dust the C display to low brightness settings
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
W hen the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. W hen this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilize s.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

9
CHAPTER 1: PRODUCT DESCRIPTION
1 .1 P ack ag e Contents
W hen unpacki ng, check if the following items are included in
the packa ge. If any of them is missing or damaged, contact your
dealer.
Q uick Start G uide
P ow er cord
Note:
♦The pictures are for reference
only. Actual items may vary
upon shipment.
V G A cab le
P ow er adap ter
RX-22G & RX-24G
displays.agneovo.com
RX-22G/RX-24G_Quick Guide_V010
Quick Start Guide
RX-22G & RX-24G LCD Monitor
L CD D isp lay
A udio cab le
Note:
Must use only the supplied power
adapter:
♦ADAPTER TECH
Model no.: ATS0 4 0 T-P120
Rating: 12V/3 .3 A
♦DELTA ELECTRONICS, INC.
Model no.: ADP-4 0 DD B
Rating: 12V/3 .3 3 A
♦Lite-on Technology Corporation
Model no.: PA-10 4 1-8 1
Rating: 12V/3 .3 3 A
Ch ap ter 1 : P roduct D escrip tion
Warranty card

1 0
PRODUCT DESCRIPTION
1 .2 Wall M ounting Installation P rep aration
1 .2 .1 Wall M ounting
1R emov e th e b ase stand.
See procedures below.
2Wall mount th e L CD disp lay.
Screw the mounting bracke t to the VESA holes at
the rear of the LCD display.
100 mm
75 mm
100 mm 75
mm
Note:
Take measures to prevent the
LCD display from falling down
and lessen possible injury and
damage to the display in case of
earthquake s or other disasters.
♦Use only the 7 5 x 7 5 mm and
10 0 x 10 0 mm wall mount ki t
recommended by AG Neovo.
♦Secure the LCD display on a
solid wall strong enough to bear
its weight.
Note:
To protect the glass panel, place a
towel or soft cloth before laying the
LCD display down.
Warning :
Ceiling mount or mount
on any other horizo ntal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

1 1
PRODUCT DESCRIPTION
1 .2 .2 R emov ing th e B ase Stand
 ay the C display face down on a at even surface
2 Remove the screws* securing the base stand from the LCD
display.
3 Detach the base stand.
Note:
(* ) The screw size is M4 x 10 mm.

1 2
PRODUCT DESCRIPTION
1 .3 L CD D isp lay Ov erv iew
1 .3 .1 Front V iew and K eyp ad B uttons
53 64 871 2
1A UT O
Hot Key: Auto Adjustment/Rotate
• For VGA input signal source, press to
perform auto adjustment.
• Press for 3 seconds to enable the Rotate
function.
• W hen OSD menu is ON, press to close the
OSD menu or exit a submenu.
2L EFT
Hot Key: Audio Volume Adjustment
• Press to display the volume bar. Then press
the LEFT ke y to decrease the volume.
• W hen OSD menu is ON, press to select an
option or adjust the settings.
3R IG H T
Hot Key: Screen Freeze
• Press to activate the screen freeze function.
To deactivate, press any ke y except for the
Power ke y.
• W hen the volume bar appears, press to
increase the volume.
• W hen OSD menu is ON, press to select
and option, adjust the settings, or enter the
submenu.
4UP
Hot Key: PIP/PBP Select
• Press repeatedly to select PIP/PBP option
    
• W hen OSD menu is ON, press to select an
option or adjust the settings.
5D OWN
Hot Key: PICTURE MODE Select
• Press repeatedly to select PICTURE MODE
option (
STANDARD  CCT    s ).
• W hen OSD menu is ON, press to select an
option or adjust the settings.
• W hen PIP is ON, press to swap the PIP main
and sub picture.
6M ENU
Press to display/hide the OSD menu.
7SOUR CE
Press to select the input signal source.
8P OWER and L ED Indicator
• Press to turn the power on or off.
• Indicate the operating status of the LCD
display:
- Lights Green when the LCD display is
turned on.
- Lights Amber when the LCD display is in
standby mode.
- Lights Off when the LCD display is turned
off.

1 3
PRODUCT DESCRIPTION
1 .3 .2 R ear V iew
S-VIDEO
COMPOSITE-1
AUDIO
IN
L
R
IN
OUT
COMPOSITE-2
IN
OUT
AUDIO
OUT
L
R
USB (SERVICE)
RS232
AUDIO INDVIDC IN HDMIDisplayPortVGA
1D C IN
Connect with the supplied power adaptor.
2D V I
Connect DVI signals input.
3H D M I
Connect HDMI signals input.
4D isp layP ort
Connect DisplayPort signals input.
5V G A
Connect VGA signals input.
6A UD IO IN
Connect audio signals input (3 .5 mm Stereo
Audio Ja ck ).
7S- V ID EO
Connect S-Video signals input.
8COM P OSIT E- 1 / COM P OSIT E- 2 IN
Connect Composite (CVBS) signals input.
9COM P OSIT E- 1 / COM P OSIT E- 2 OUT
Connect Composite (CVBS) signals output.
10 A UD IO IN
Connect audio signals input (RCA Stereo
Audio Ja ck) .
11 A UD IO OUT
Connect audio signals output (RCA Stereo
Audio Ja ck) .
12 USB (SER V ICE)
Connect USB 2.0 for service.
13 R S2 3 2
Connect RS23 2 input from external
equipment.
1 2 3 4 5 6
7
8
9
8
9
12
13
10
11

CHAPTER 2: MAKING CONNECTIONS
1 4
2 .1 Connecting th e P ow er
1Connect the power cord to the power adapter.
2Connect the power adapter to the DC power input at the rear of the LCD display.
3Connect the power cord plug to a power outlet or a power supply.
DC IN
Caution:
♦Make sure that the LCD display is
not connected to the power outlet
before maki ng any connections.
Connecting cables while the power
is ON may cause electric shock or
personal injury.
Caution:
♦W hen unplugging the power cord,
hold the power cord by the plug
head. Never pull by the cord.
Ch ap ter 2 : M ak ing Connections

1 5
MAKING CONNECTIONS
2 .2 Connecting Inp ut Source Sig nals
2 .2 .1 Connecting a Comp uter
Using V G A Cab les
Connect one end of a VGA cable to the VGA connector of the LCD display and the other end to the VGA
connector of the computer.
VGA
Using D V I Cab les
Connect one end of a DVI (DVI-D) cable to the DVI connector of the LCD display and the other end to the DVI
connector of the computer.
DVI

1 6
MAKING CONNECTIONS
Using H D M I Cab les
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of the computer.
HDMI
Using D isp layP ort Cab les
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of the computer.
DisplayPort

1 7
MAKING CONNECTIONS
Using R S2 3 2 Cab les
Connect one end of an RS23 2 cable to the RS23 2 connector of the LCD display and the other end to the
RS23 2 connector of the computer.
RS232
Using A udio Cab les
Connect one end of an audio cable to the AUDIO IN connector at the rear of the LCD display and the other
end to the audio out connector of the computer.
AUDIO IN

1 8
MAKING CONNECTIONS
2 .2 .2 Connecting a V ideo D ev ice
Using Comp osite (CV B S) Cab les
Connect one end of a Composite (CVBS) cable to the COMPOSITE 1 / COMPOSITE 2 IN connector of the
LCD display and the other end to the Composite (CVBS) connectors of your device.
For audio input, connect an RCA cable to the AUDIO IN connectors of the LCD display and the audio out
connector of your device.
For video looping, connect one end of a Composite (CVBS) cable to the COMPOSITE 1 / COMPOSITE 2
OUT connector of the LCD display and the other end to the COMPOSITE 1 / COMPOSITE 2 IN connector of
the additional display.
COMPOSITE-1
AUDIO
IN
L
R
IN
COMPOSITE-2
IN
COMPOSITE-1
AUDIO
IN
L
R
IN
OUT
COMPOSITE-2
IN
OUT
AUDIO
OUT
L
R
or

1 9
MAKING CONNECTIONS
Using S- V ideo Cab les
Connect one end of an S-Video cable to the S-VIDEO connector of the LCD display and the other end to the
S-VIDEO connector of your device.
For audio input, connect an RCA cable to the AUDIO IN connectors of the LCD display and the audio out
connector of your device.
AUDIO
IN
L
R
S-VIDEO
Using H D M I Cab les
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of your device.
HDMI

2 0
MAKING CONNECTIONS
Using D isp layP ort Cab les
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of your device.
DisplayPort