AG Neovo X-22E User manual

X-22E & X-24E LED-Backlit Display
User Manual
displays.agneovo.com

TABLE OF CONTENTS
2
S a f e t y I n f o r m a t i o n
WEEE.......................................................................................................................................................4
P r e c a u t i o n s
Notice.......................................................................................................................................................5
Cautions When Setting Up.......................................................................................................................5
Cautions When Using...............................................................................................................................6
Cleaning and Maintenance.......................................................................................................................6
Notice for the LCD Display.......................................................................................................................7
C h a p t e r 1 : P r o d u c t D e s c r i p t i o n
1.1 Package Contents..............................................................................................................................8
1.2 Wall Mounting Installation Preparation...............................................................................................9
1.2.1 Wall Mounting..........................................................................................................................9
1.2.2 Removing the Base Stand.......................................................................................................9
1.3 LCD Display Overview .......................................................................................................................10
1.3.1 Front View and Keypad Buttons..............................................................................................10
1.3.2 Rear View................................................................................................................................11
C h a p t e r 2: M a k i n g C o n n e c t i o n s
2.1 Connecting the Power........................................................................................................................12
2.2 Connecting Input Source Signals.......................................................................................................13
2.2.1 Connecting a Computer ..........................................................................................................13
Using VGA Cables ......................................................................................................................... 13
Using DVI Cables...........................................................................................................................13
Using DisplayPort Cables ..............................................................................................................14
Connecting an Audio Device..........................................................................................................14
2.2.2 Connecting a Video Device.....................................................................................................15
Using HDMI Cables........................................................................................................................15
C h a p t e r 3 : U s i n g t h e L C D D i s p l a y
3.1 Turning on the Power.........................................................................................................................16
3.2 Selecting the Input Source Signal......................................................................................................16
3.3 Adj usting the Volume..........................................................................................................................17
3.4 Locking the OSD Menu......................................................................................................................17
3.5 Using Picture-in-Picture (PIP) ............................................................................................................18
3.5.1 PIP Options.............................................................................................................................18
3.5.2 PIP Swap.................................................................................................................................19
3.6 Using Auto Adj ustment Function ........................................................................................................19
C h a p t e r 4: O n S c r e e n D i s p l a y M e n u
4.1 Using the OSD Menu .........................................................................................................................20
4.2 OSD Menu Tree .................................................................................................................................22

3
TABLE OF CONTENTS
C h a p t e r 5: A d j u s t i n g t h e L C D D i s p l a y
5.1 BRIGHTNESS....................................................................................................................................25
5.2 COLOUR TEMP..................................................................................................................................27
5.3 IMAGE SETTING...............................................................................................................................28
5.4 ASPECT RATIO..................................................................................................................................31
5.5 PIP SETTING.....................................................................................................................................32
5.6 ANTI-BURN-IN...................................................................................................................................34
5.7 OSD SETTING...................................................................................................................................35
5.8 AUDIO SETTING................................................................................................................................36
5.9 SYSTEM.............................................................................................................................................37
5.10 ECO SMART....................................................................................................................................39
5.11 INPUT SELECT................................................................................................................................40
C h a p t e r 6: A p p e n d i x
6.1 Warning Messages.............................................................................................................................41
6.2 Troubleshooting..................................................................................................................................42
6.3 Transporting the LCD Display ............................................................................................................44
&KDSWHU6SHFL¿FDWLRQV
7.1 Display Specications ........................................................................................................................45
7.2 Display Dimensions............................................................................................................................46
7.2.1 X-22E Dimensions...................................................................................................................46
7.2.2 X-24E Dimensions...................................................................................................................46

SAFETY INFORMATION
4
W EEE
Information for users applicable in European Union countries.
e syol on te poct o its pacain sinies tat tis poct as to e
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.

5
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
S y m b o l s u s e d i n t h i s m a n u a l
This icon indicates the existence of a potential hazard that could result in personal inj ury
or damage to the product.
This icon indicates important operating and servicing information.
N o t i c e
• Read this User Manual carefully before using the LCD display and keep it for future reference.
• e poct specications an ote inoation poie in tis se anal ae o eeence only. ll
information is subj ect to change without notice. Updated content can be downloaded from our web site at
d i s p l a y s . a g n e o v o . c o m .
• To register online, go to d i s p l a y s . a g n e o v o . c o m .
• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may
affect the determination of the warranty period.
C a u t i o n s W h e n S e t t i n g U p
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subj ect
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp obj ects into the LCD display through the ventilation holes.
Doin so ay case acciental e electic soc o aae te D isplay.
P r e c a u t i o n s

6
PRECAUTIONS
C a u t i o n s W h e n U s i n g
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
display and be easily accessible.
If an extension cord is used with the LCD display,
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
may be stepped on.
 te D isplay ill not e se o an inenite
period of time, unplug the power cord from the
power outlet.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
case e o electic soc.
Do not unplug or touch the power cord with wet
hands.
C l e a n i n g a n d M a i n t e n a n c e
The LCD display comes with NeoVTM Optical
Glass. Use a soft cloth lightly moistened with a mild
detergent solution to clean the glass surface and the
housing.
Do not rub or tap the surface of the glass with sharp
or abrasive items such as a pen or screwdriver. This
may result in scratching the surface of the glass.
Do not attempt to service the LCD display yourself,
ee to alie seice pesonnel. penin o
removing the covers may expose you to dangerous
voltage or other risks.
W a r n i n g :
Unplug the power cord
from the power outlet and
ee to alie seice
personnel under the following
conditions:
ƇWhen the power cord is
damaged.
ƇIf the LCD display has been
dropped or the housing has
been damaged.
ƇIf the LCD display emits smoke
or a distinct odor.
W a r n i n g :
Ceiling mount or mount
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
 eoo o consltations an
solutions to help ensure a most
pleasale an lllin isplay
experience.

7
PRECAUTIONS
N o t i c e f o r t h e L C D D i s p l a y
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• st te D isplay to lo itness settins.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilizes.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

CHAPTER 1: PRODUCT DESCRIPTION
8
1 . 1 P a c k a g e C o n t e n t s
When unpacking, check if the following items are included in
the package. If any of them is missing or damaged, contact your
dealer.
U s e r M a n u a l
P o w e r c o r d
N o t e :
ƇThe pictures are for reference
only. Actual items may vary
upon shipment.
V G A c a b l e
P o w e r a d a p t e r
L C D D i s p l a y
A u d i o c a b l e
N o t e :
Must use only the supplied power
adapter:
ƇLite-on Technology Corporation
Model no.: PA-1041-81
Rating: 12V/3.33A
ƇDELTA ELECTRONICS, INC.
Model no.: ADP-40DD B
Rating: 12V/3.33A
C h a p t e r 1 : P r o d u c t D e s c r i p t i o n
W a r r a n t y c a r d

9
PRODUCT DESCRIPTION
1 . 2 W a l l M o u n t i n g I n s t a l l a t i o n P r e p a r a t i o n
1 . 2. 1 W a l l M o u n t i n g
1R e m o v e t h e b a s e s t a n d .
See procedures below.
2W a l l m o u n t t h e L C D d i s p l a y .
Screw the mounting bracket to the VESA holes at
the rear of the LCD display.
100 mm
75 mm
100 mm 75
mm
1 . 2. 2 R e m o v i n g t h e B a s e S t a n d
1 Lay the LCD display
ace on on a at
even surface.
2 Remove the four
screws securing the
base stand from the
LCD display.
3 Detach the base
stand.
4 Lock four screws back.
N o t e :
Take measures to prevent the
LCD display from falling down
and lessen possible inj ury and
damage to the display in case of
earthquakes or other disasters.
ƇUse only the 75 x 75 mm and
100 x 100 mm wall mount kit
recommended by AG Neovo.
ƇSecure the LCD display on a
solid wall strong enough to bear
its weight.
N o t e :
To protect the glass panel, place a
towel or soft cloth before laying the
LCD display down.
W a r n i n g :
Ceiling mount or mount
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasale an lllin isplay
experience.

1 0
PRODUCT DESCRIPTION
1 . 3 L C D D i s p l a y O v e r v i e w
1 . 3 . 1 F r o n t V i e w a n d K e y p a d B u t t o n s
1
64 75 982 3
S O U R C E
• Press to select the input signal source.
U P
Hot Key: PIP Select
• Press repeatedly to select PIP option.
• During OSD menu selection, press to move
up a menu or submenu.
M EN U
• Press to display the OSD menu.
• Press again to hide the OSD menu.
D O W N
Hot Key: Aspect Ratio
• When PIP is on, press to SWAP the PIP
main and sub picture.
• During OSD menu selection, press to move
up a menu or submenu.
L EF T
Hot Key: Volume Up
• Press to display the volume screen. Then
press again to decrease the volume.
• During OSD menu selection, press to adj ust
the settings.
R I G H T
Hot Key: Volume Down
• Press to display the volume screen. Then
press again to increase the volume.
• During OSD menu selection, press to select
an option and adj ust the settings.
A U T O
Hot Key: For VGA input signal source,
press to perform auto adjustment.
• During OSD menu selection, press to close
the OSD menu or exit a submenu.
D i s p l a y s c r e e n
The LCD display screen is protected by
NeoVTM Optical Glass.
1
7
6
5
4
3
2
8
P O W ER / L ED i n d i c a t o r
• Press to turn the power on or off.
Green - Power on
Amber - Standby mode
Off - Power off
9
Ec o S m a r t s e n s o r : Detect ambient lighting
conditions and automatically adj ust the
brightness levels. Refer to page 40 “ ECO
SMART” for more information.
10
10

1 1
PRODUCT DESCRIPTION
1 . 3 . 2 R e a r V i e w
AUDIO INDVI HDMI DisplayPort VGA
DC IN
1
1D C p o w e r i n p u t
Use to connect the power cord.
4D i s p l a y P o r t c o n n e c t o r
Use to connect a PC using a DisplayPort
cable for digital input signal.
2D V I c o n n e c t o r
Use to connect a PC using a DVI cable
for digital input signal.
5V G A c o n n e c t o r
Use to connect a PC using a VGA cable for
analogue input signal.
3H D M I c o n n e c t o r
Use to connect an input device using
an HDMI cable for digital input signal.
6A u d i o p o r t
Use to connect an audio cable for the PC’s
audio input.
34 5 6
2

CHAPTER 2: MAKING CONNECTIONS
1 2
2. 1 C o n n e c t i n g t h e P o w e r
1Connect the power cord to the power adapter.
2Connect the power adapter to the DC power input at the rear of the LCD display.
3Connect the power cord plug to a power outlet or a power supply.
DC IN
C a u t i o n :
ƇMake sure that the LCD display is
not connected to the power outlet
before making any connections.
Connecting cables while the power
is ON may cause electric shock or
personal inj ury.
C a u t i o n :
ƇWhen unplugging the power cord,
hold the power cord by the plug
head. Never pull by the cord.
C h a p t e r 2: M a k i n g C o n n e c t i o n s

1 3
MAKING CONNECTIONS
2. 2 C o n n e c t i n g I n p u t S o u r c e S i g n a l s
2. 2. 1 C o n n e c t i n g a C o m p u t e r
U s i n g V G A C a b l e s
Connect one end of a D-sub cable to the VGA connector of the LCD display and the other end to the D-sub
connector of the computer.
VGA
U s i n g D V I C a b l e s
Connect one end of a DVI cable to the DVI connector of the LCD display and the other end to the DVI
connector of the computer.
DVI

1 4
MAKING CONNECTIONS
U s i n g D i s p l a y P o r t C a b l e s
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of the computer.
DisplayPort
C o n n e c t i n g a n A u d i o D e v i c e
Connect one end of an audio cable to the audio port at the rear of the LCD display and the other end to the
audio out port of the computer.
AUDIO IN

1 5
MAKING CONNECTIONS
2. 2. 2 C o n n e c t i n g a V i d e o D e v i c e
U s i n g H D M I C a b l e s
Connect one end of an HDMI cable to the HDMI connector of the LCD display and the other end to the HDMI
connector of your device.
HDMI

CHAPTER 3: USING THE LCD DISPLAY
1 6
3 . 1 T u r n i n g o n t h e P o w e r
1Plug the power cord to a power outlet or power supply.
2Touch the P O W ER button to turn the LCD display on.
The LED indicator turns GREEN.
When the LCD display is turned on, touch the POWER
button to turn off the LCD display.
The LED indicator turns off.
N o t e :
ƇThe LCD display still consumes
power as long as the power
cord is connected to the power
outlet. Disconnect the power
cord to completely cut off
power.
3 . 2 S e l e c t i n g t h e I n p u t S o u r c e S i g n a l N o t e s :
ƇThis function works only if
S O U R C E D ET EC T is set to
MANUAL. Refer to page 37.
ƇAfter selecting an input source
signal, the input source signal
message appears on the
sceen iey.
For example, HDMI is selected
the following message is
displayed.
HDMI INPUT
ƇIf the selected input source
signal is not connected to the
LCD display or is turned off, the
no signal message is displayed
on the screen.
NO
SIGNAL
ƇIf the resolution or the graphics
card of the connected computer
is set too high, the input out of
range message is displayed.
INPUT SIGNAL
OUT OF RANGE
P O W ER button
L ED indicator
S O U R C E button
1Touch the button to call out the input source menu.
VGA
DVI
HDMI
DP
2Touch the por qbutton to highlight an input source.
3Touch the ubutton to select the input source.
C h a p t e r 3 : U s i n g t h e L C D D i s p l a y

1 7
USING THE LCD DISPLAY
3 . 3 A d j u s t i n g t h e V o l u m e
1 Touch the tor ubutton to call out the volume bar.
2Touch the ubutton to increase volume or the tbutton to decrease volume.
To mute the audio, set the volume to 0.
3 . 4 L o c k i n g t h e O S D M e n u
Lock the OSD menu to protect the LCD display from unauthorised users or from accidentally pressing the
keypad.
To lock the OSD, press and hold the keypad buttons listed below for at least 5 seconds or until the
OSD
LOCK OUT message appears.
When the OSD is locked, all keypad buttons are inactivated.
T y p e o f O S D L o c k L o c k O p e r a t i o n U n l o c k O p e r a t i o n
Lock all buttons Touch and hold the u, p, and q
buttons for 5 seconds.
Touch and hold the u, p, and q
buttons for 5 seconds or until the OSD
menu appears.
Lock all buttons except
the P O W ER button. Touch and hold the t, p, and q
buttons for 5 seconds.
Touch and hold the t, p, and q
buttons for 5 seconds or until the OSD
menu appears.
V O L U M E buttons

1 8
USING THE LCD DISPLAY
3 . 5 U s i n g P i c t u r e -i n -P i c t u r e ( P I P )
The Picture-in-Picture (PIP) feature allows viewing of more than one input source signal on the LCD display.
3 . 5. 1 P I P O p t i o n s
Touch the pbutton repeatedly to enable and scroll among the PIP options. Options are as follows:
• PIP On: The sub source signal is displayed within the main source signal.
• PBP (Picture-by-Picture): The main source and the sub source signals are displayed side by side with
equal display size.
• PIP Off: PIP function is disabled, only the main source signal is displayed.
N o t e :
ƇThe main source and sub
source signals can be set in
PIP Setting, see page 32.
ƇSome input source signal
combinations do not support
PIP. See PIP Compatibility
table on page 33.
PIP On
PBP
PIP Off

1 9
USING THE LCD DISPLAY
3 . 5. 2 P I P S w a p
The main and the sub source signals set in PIP Setting can be easily
swapped using the keypad.
Main source
Sub source
Touch the qbutton to swap the main source and the sub source
signals. See illustration below.
Main source
Sub source
3 . 6 U s i n g A u t o A d j u s t m e n t F u n c t i o n
Auto Adj ustment function automatically tunes the LCD display to its
optimal setting, including horizontal position, vertical position, clock,
and phase.
Touch the button to perform auto adj ustment.
The message auto adj usting is displayed on the screen.
AUTO
ADJUSTING
During auto adj ustment, the screen will slightly shake for a few
seconds.
When the message disappears, auto adj ustment is completed.
N o t e :
ƇPIP Swap can only be executed
if PIP is enabled, see page 33.
N o t e :
ƇAuto Adj ustment function is
available only during VGA input
signals.
ƇIt is recommended to use the
auto adj ustment function when
using the LCD display for the
st tie o ate a esoltion o
frequency change.

CHAPTER 4: ON SCREEN DISPLAY MENU
20
4. 1 U s i n g t h e O S D M e n u
O p e r a t i o n
1Display the main menu screen.
1920x1080 60Hz
BRIGHTNESS
COLOUR TEMP.
IMAGE SETTING
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM
ECO SMART
INPUT SELECT
LANGUAGE
INFORMATION
EXITENTER SELECT
BRIGHTNESS 50
BLACK LEVEL 50
BACKLIGHT50
CONTRAST50
Touch .
2Select the menu.
1920x1080 60Hz
BRIGHTNESS
COLOUR TEMP.
IMAGE SETTING
ASPECT RATIO
PIP SETTING
ANTI-BURN-IN
OSD SETTING
AUDIO SETTING
SYSTEM
ECO SMART
INPUT SELECT
LANGUAGE
INFORMATION
EXITENTER SELECT
BRIGHTNESS 50
BLACK LEVEL 50
BACKLIGHT50
CONTRAST50
1Touch the por qbutton.
2 Touch the ubutton to enter the
submenu.
Navigation Window
C h a p t e r 4: O n S c r e e n D i s p l a y M e n u