AG Neovo DS-55 User manual

•Important Safety Instructions………………………….1
–Safety precautions and maintenance………………............1
–Use………………………………………………………………4
–Installation Notes………………………………………………7
•Package Content……………………………………………..9
–Unpacking……………………………………………………...9
–Accessories……………………………………………..........10
–Overview……………………………………………………....11
•Setting Up the Display……………………………………13
–Step1 : Putting the dual-sided display upside ……...........13
–Step2 : Remove the three I/O covers on the sides............14
–Step3 : Remove the downside cover……………………....15
–Step4 : Link power box to dual-sided display………..........16
–Step5 : Connect by HDMI connector……………………….18
–Step6 : Reinstall the downside cover and I/O covers……..19
–Step7 : Connect the power cord…………………………….20
–Step8 : Using the Remote Control…………………………..21
–OSD Setting Menu…………………………………………..22
•Trouble shooting…………………………………...............26
•Specifications…………………………………….................27
•Product Dimensions………………………………...........28
Table of contents

Safety precautions and maintenance
WARNING: Use of control, adjustments or
procedures other than those specified in this
documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
Important Safety Instructions
Read and follow these instructions when connecting and
using your display:
Operation:
•Keep the display out of direct sunlight and away from stoves or any
other heat sources.
•Remove any object that could fall into ventilation holes of power box
or prevent proper cooling of the display’s electronics.
•Don’t block the ventilation holes on the power box.
•When positioning the display, make sure the power plug and outlet
are easily accessible.
•When turning off the display by detaching the power cord, wait 6
seconds before re-attaching the power cord for normal operation.
•Ensure the use of an approved power cord provided by AUO at all
times. If your power cord is missing, please contact your local service
center.
•Don’t subject the display to severe vibration or high impact conditions
during operation.
•Don’t knock or drop the display during operation or transportation.
•Provide an earthing connection before the mains plug is connected to
the mains.And, when disconnecting the earthing connection, be sure to
disconnect after pulling out the mains plug from the mains.
1

Safety precautions and maintenance
Maintenance:
•To protect your display from possible damage, do not put excessive
pressure on the display.
•Unplug the display if you are not going to use it for an extensive
period of time.
•Unplug the display if you need to clean it with a slightly damp cloth.
The screen may be wiped with a dry cloth when the power is off.
However, never use organic solvent, such as, alcohol, or ammonia-
based liquids to clean your display.
•To avoid the risk of shock or permanent damage to the set, do not
expose the display to dust, rain, water or an excessively moist
environment.
•If your display becomes wet, wipe it with dry cloth as soon as possible.
•If a foreign substance or water gets in your display, turn the power off
immediately and disconnect the power cord. Then remove the foreign
substance or water.
•Don’t store or use the display in locations exposed to heat, direct
sunlight or extreme cold.
2

Safety precautions and maintenance
Read and follow these instructions when connecting and using
your display:
•Unplug the display if you are not going to use it for an extensive
period of time.
•Unplug the display if you need to clean it with a slightly damp cloth.
The screen may be wiped with a dry cloth when the power is
off. However, never use alcohol, solvents or ammonia-based liquids.
•Keep the display out of direct sunlight and away from stoves or any
other heat sources.
•Remove any object that could fall into the vents or prevent proper
cooling of the display’s electronics.
•Don’t block the ventilation holes on the power box.
•Keep the display dry. To avoid electric shock, do not expose it to rain
or excessive moisture.
•When turning off the display by detaching the power cable or DC
power cord, wait for 6 seconds before re-attaching the power
cable or DC power cord for normal operation.
•When positioning the display, make sure the power plug and outlet
are easily accessible.
•Consult a service technician if the display does not operate normally
after having followed the instructions in this manual.
3

Use
•Don’t turn the ventilation hole of Power Box upside down.
As shown in the picture below.
The ventilation hole of
power box
It is prohibited to
place tilt
The ventilation hole of
power box
It is prohibited to turn the
ventilation hole of Power
Box upside down.
4

Use
•When you install the display, please don’t use the “bottom
side” I/O hole and open the I/O cover . As shown in the
picture below.
The “bottom side” I/O cover
can’t be opened.
5

Use
Disconnect devices:
•For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
6
Remote Controller Precautions:
•This product requires remote switch (ON/OFF) from Front Side ; the
Back Side only has OSD function operated by remote controller.
Front Side Back Side
The Front Side have a product
label.

Installation Notes
There have 8 mounting holes on the side
of the display set (M4x15mm)
F
7

Installation Notes
Please make sure you
have a solid installation.
As shown in the picture.
You can install the display
set by screws x 8
(M4x15mm)
8

Package Content
Unpacking
•This product is packed in a carton, together with the standard
accessories.
•Due to the size and weight of this display it is recommended for two
people to move it.
•After opening the carton, ensure that the contents are complete and in
good condition.
9

Accessories
Dual-sided Display x1
Power Cord x1
PC Box x1
(with 24V&12V line)
10
Remote Controller x1
(Battery : CR 2025 3V)

Over View
Front View
Top View
Diagonal View
Side View
11

Over View
1. Display (Dual-sided)
2. Display Set
3. Remote control sensor (Dual-sided)
4. Mounting hole x 8 (single side have 4)
5. I/O cover x 3
1
2
4
5
3
12

Setting Up The Display
Step1 : Putting the dual-sided display upside
While the display put
upside , the screw will
be seen on the left.
13

Step2 : Remove the three I/O covers on the sides
Remove I/O cover
screws x 3(M3x6mm)
14

Step3 : Remove the downside cover
Tear down the
downside cover.
screws x 10(M3x6mm)
15

Step4 : Connect Power Box to Dual-sided Display
Power Box
Dual-sided
Display
24V*1
Red line
(10 pin)
12V*1
Yellow line
(8 pin)
1
2
16

Connect the 24V (10 pin) power line
1 Connect the 12V (8 pin) power line
12V*1
Yellow line
(8 pin)
24V*1
Red line
(10 pin)
2
1
2
17
Step4 : Connect Power Box to Dual-sided Display

Step5 : Connect by HDMI connector
Plug two HDMI cables into the cabinet.
And ensure that all cable plugs are firmly fitted to
the equipment jacks.
HDMI HDMI
18