AG Neovo SC-19E User manual

SC-19E, SC-22E, SC-24E & SC-27E LED-Backlit Display
User Manual

TABLE OF CONTENTS
Contents
Federal Communications Commission (FCC) Notice (U.S. Only)................................................................1
WEEE...........................................................................................................................................................2
Notice ...........................................................................................................................................................3
Cautions When Setting Up ........................................................................................................................... 3
Cautions When Using...................................................................................................................................4
Cleaning and Maintenance........................................................................................................................... 4
Notice for the LCD Display ........................................................................................................................... 5
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents .................................................................................................................................. 6
1.2 Installation ..............................................................................................................................................7
1.2.1 Installing the Stand...................................................................................................................... 7
1.2.2 Adjusting the Viewing Angle ........................................................................................................8
1.2.3 Wall Mounting..............................................................................................................................8
1.3 Control Buttons..................................................................................................................................... 10
1.4 Overview .............................................................................................................................................. 11
1.4.1 Front View ................................................................................................................................. 11
1.4.2 Rear View..................................................................................................................................12
CHAPTER 2: MAKING CONNECTIONS
2.1 Connecting the AC Power .................................................................................................................... 13
2.2 Connecting Input Source Signals ......................................................................................................... 14
2.2.1 Connecting an Audio Device ..................................................................................................... 15
2.3 Connecting a Video Device .................................................................................................................. 16
2.4 Connecting a USB Storage Device (for rmware upgrade).................................................................. 16
2.5 Connecting an External Audio Device .................................................................................................. 17
CHAPTER 3: USING THE LCD DISPLAY
3.1 Turning on the Power ........................................................................................................................... 18
3.2 Using FREEZE Function ...................................................................................................................... 18
3.3 Adjusting the Volume............................................................................................................................ 19
3.4 Muting Audio......................................................................................................................................... 20
3.5 Locking the Control Buttons ................................................................................................................. 20
CHAPTER 4: ON SCREEN DISPLAY MENU
4.1 Using the OSD Menu ........................................................................................................................... 22
4.2 OSD Menu Tree ................................................................................................................................... 23
CHAPTER 5: ADJUSTING THE LCD DISPLAY
5.1 Image Setting .......................................................................................................................................26
5.2 Audio Setting ........................................................................................................................................30
5.3 System .................................................................................................................................................31
5.4 Input Select ..........................................................................................................................................33

TABLE OF CONTENTS
CHAPTER 6: APPENDIX
6.1 Warning Messages...............................................................................................................................34
6.2 Troubleshooting....................................................................................................................................35
6.3 Transporting the LCD Display .............................................................................................................. 36
CHAPTER 7: SPECIFICATIONS
7.1 Display Specications .......................................................................................................................... 38
7.2 Display Dimensions..............................................................................................................................39

1
SAFETY INFORMATION
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer
device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive
moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

2
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.

3
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD display and keep it for future reference.
• The product specications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
http://www.agneovo.com.
• To register online, go to http://www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may
affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doing so may cause accidental re, electric shock or damage the LCD display.

4
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
display and be easily accessible.
If an extension cord is used with the LCD display,
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
may be stepped on.
If the LCD display will not be used for an indenite
period of time, unplug the power cord from the
power outlet.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
cause re or electric shock.
Do not unplug or touch the power cord with wet
hands.
Cleaning and Maintenance
Use a soft cloth lightly moistened with a mild
detergent solution to clean the screen surface and
the housing.
Do not rub or tap the surface of the screen
with sharp or abrasive items such as a pen or
screwdriver. This may result in scratching the surface
of the screen.
Do not attempt to service the LCD display yourself,
refer to qualied service personnel. Opening or
removing the covers may expose you to dangerous
voltage or other risks.
Warning:
Unplug the power cord
from the power outlet and
refer to qualied service
personnel under the following
conditions:
♦When the power cord is
damaged.
♦If the LCD display has been
dropped or the housing has
been damaged.
♦If the LCD display emits smoke
or a distinct odor.
Warning:
Ceiling mount or mount
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

5
PRECAUTIONS
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Execute the Anti-Burn-inTM function of the LCD display. Refer to page 31.
• Switch desktop backgrounds regularly.
• Adjust the LCD display to low brightness settings.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the screen surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the screen surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilizes.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

CHAPTER 1: PRODUCT DESCRIPTION
6
1.1 Package Contents
When unpacking, check if the following items are included in the package. If any of them is missing or
damaged, contact your dealer.
SC-19E SC-22E SC-24E SC-27E
LCD display
Stand for SC-
19E/22E/24E
Stand for SC-27E Base for SC-
19E/22E/24E
Base for SC-27E
Power Cord D-Sub Cable Audio Cable Warranty Card
SC-19E, SC-22E, SC-24E & SC-27E
www.agneovo.com
SC-19E/SC-22E/SC-24E/SC-27E_Quick Guide_V010
Quick Start Guide
SC-19E, SC-22E, SC-24E & SC-27E LED-Backlit Display
Quick Start Guide
Note:
• Use only the supplied power cord.
• The above pictures are for reference only. Actual items may vary upon shipment.
Chapter 1: Product Description

7
PRODUCT DESCRIPTION
1.2 Installation
1.2.1 Installing the Stand
1. Place the LCD display with the screen side down on a cushioned surface.
2. Attach the base to the stand.
-SC-19E/22E/24E models: Press rmly on the base to secure the latches on the base into the slots on
the stand.
-SC-27E model: Attach the base to the stand and x with the screw to join them tightly.
3. Attach the stand to the display.
SC-19E/22E/24E SC-27E

8
PRODUCT DESCRIPTION
1.2.2 Adjusting the Viewing Angle
For optimal viewing, it is recommended to look at the full face of the screen, then adjust the screen of the LCD display
angle according to your preference.
Hold the stand so that the screen does not topple when you make the adjustment.
You are able to adjust the screen angle as illustrated below:
23°~-5°
1.2.3 Wall Mounting
To wall mount the LCD display, do the following steps:
1. Remove the stand.
Please refer to page 36.

9
PRODUCT DESCRIPTION
2. Wall mount the LCD display.
Screw the mounting bracket to the VESA holes at the rear of the LCD display.
HDMI D-SUBCVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
100 mm
100 mm
HDMI D-SUBCVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
100 mm
100 mm
HDMI D-SUB CVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
100
mm
100 mm
HDMID-SUB CVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
100
mm
100 mm
SC-19E SC-22E
SC-24E SC-27E
Note: Take measures to prevent the LCD display from falling down and lessen possible injury and damage
to the display in case of earthquakes or other disasters.
• Use only the 100 x 100 mm wall mount kit recommended by AG Neovo. All
AG Neovo wall mount kits comply with VESA standard.
• Secure the LCD display on a solid wall strong enough to bear its weight.
• It is suggested to wall mount the LCD display without tilting it facing
downward.

10
PRODUCT DESCRIPTION
1.3 Control Buttons
HDMI D-SUBCVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
1
2
3
4
5
6
1[ ] Source/Exit
• Call out the Source quick menu. Press
the button repeatedly to switch the
input source. Then press the button to
conrm.
• Press and the hold the button to
freeze/unfreeze the screen. Refer to page
18.
• During OSD menu, close the OSD menu
or exit a submenu.
• During volume adjustment, close the quick
menu.
2[ ] Up
• Call out the Volume quick menu. Then
press the / button to adjust the
volume level. Refer to page 19.
• During OSD menu, scroll through the
menu options, select an option, and adjust
the settings.
3[ ] Down
• Call out the Volume quick menu. Then
press the / button to adjust the
volume level. Refer to page 19.
• During OSD menu, scroll through the
menu options, select an option, and adjust
the settings.
4[ ] Menu/Enter
• Call out the OSD menu when OSD menu
is off.
• During OSD menu, conrm the selection
or enter a submenu.
• Press and hold the button to mute/
unmute audio. Refer to page 20.
5[ ] Power
Turn the LCD display on. Press it again
to turn the LCD display off. Refer to page
18.
6Power indicator
Indicate the operating status of the LCD
display:
- Lights blue when the LCD display is
turned on.
- Lights amber when the LCD display is in
standby mode.
- Lights off when the LCD display is turned
off.

11
PRODUCT DESCRIPTION
1.4 Overview
1.4.1 Front View
SC-19E SC-22E
SC-24E SC-27E
1
2
1
2
1
2
1
2
1Display screen
2Control buttons
Press the button to perform its function. For more information about each button, refer to page 10.

12
PRODUCT DESCRIPTION
1.4.2 Rear View
HDMI D-SUBCVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
HDMI D-SUBCVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
HDMI D-SUB CVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
HDMID-SUB CVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
HDMI D-SUB CVBS
IN
CVBS
OUT
AUDIO
IN
AUDIO
OUT
SC-19E SC-22E
SC-24E SC-27E
1 2 3 54 6 7 8
9 9
9 9
1AC Power input
Use to connect the power cord.
6AUDIO IN connector
Use to connect an audio cable for audio input.
2HDMI connector
Use to connect an HDMI cable for digital input
signal.
7AUDIO OUT connector
Use to connect an audio cable for audio
output signal to an external audio device.
3D-SUB (VGA) connector
Use to connect a D-SUB (VGA) cable for
analogue input signal.
8USB connector
Use to connect a ash disk for rmware
upgrade.
4CVBS IN connector
Use to connect a composite cable for CVBS
input signal from a video device.
9Kensington security slot
Used for security and theft prevention.
5CVBS OUT connector
Use to connect a composite cable for CVBS
output signal to a video device.

13
CHAPTER 2: MAKING CONNECTIONS
CAUTION:
Make sure that the LCD display is not connected to the power outlet before making any
connections. Connecting cables while the power is ON may cause possible electric shock or
personal injury.
2.1 Connecting the AC Power
1. Connect the power cord to the AC power input at the rear of the LCD display.
2. Connect the power cord plug to a power outlet or a power supply.
CAUTION:
When unplugging the power cord, hold the power cord by the plug head. Never pull by the
cord.
Chapter 2: Making Connections

14
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
Input source signals can be connected with either of the following cables:
Computer
HDMI D-SUB
HDMI D-SUB
• VGA
Connect one end of a D-SUB (VGA) cable to the D-SUB
(VGA) connector of the LCD display and the other end to
the D-SUB (VGA) connector of the computer.
• HDMI
Connect one end of an HDMI cable to the HDMI connector
of the LCD display and the other end to the HDMI
connector of the computer.

15
MAKING CONNECTIONS
2.2.1 Connecting an Audio Device
1. Connect one end of an audio cable to the AUDIO IN connector at the rear of the LCD
display.
2. Connect the other end of an audio cable to the AUDIO OUT connector of the computer.
AUDIO
IN
AUDIO
OUT
Computer

16
MAKING CONNECTIONS
2.3 Connecting a Video Device
1. Connect one end of a composite cable to the CVBS IN connector at the rear of the LCD
display.
2. Connect the other end of a composite cable to the CVBS OUT connector of your device.
2.4 Connecting a USB Storage Device (for rmware upgrade)
Connect a USB storage device to the USB port of the LCD display for rmware upgrade.
Video Player
CVBS
IN
CVBS
OUT
CVBS
OUT

17
MAKING CONNECTIONS
2.5 Connecting an External Audio Device
1. Connect one end of an audio cable to the AUDIO OUT connector at the rear of the LCD
display.
2. Connect the other end of an audio cable to the AUDIO IN connector of the external audio
device.
AUDIO
OUT
AUDIO
IN
Audio Device