AGame 166044 Owner's manual

Style #166044
7 ft Trampoline with Sunshade
Customer Service: [phone]
7:00 am to 12:00 am CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
(Made in China)
Please keep this instruction manual for future reference
Assembly Instructions
& User’s Manual

Table of Contents
Note: Before beginning assembly of product, make sure
all parts are present. Compare parts with package content
list and hardware contents. If any part is missing or
damaged, do not attempt to assemble the unit. Contact
customer service for replacement parts.
Warnings 3
Basic Trampoline Skills 4
Tools and Parts 6
Assembly Instructions 8
Care and Maintenance 22
Warranty Information 23
Page 2 of 23

Page 3 of 23
Warnings
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read and follow all warnings, precautions, and instructions
in this manual before assembling and using the trampoline.
This product is intended for use by children above 3 years of age.
This enclosure is to be used only in connection with this trampoline.
Read and follow all warnings and instruction.
This product is intended to be assembled by an adult.
Maximum weight limited 82 kg / 180 lbs.
Warning! Not suitable for children under 36 months. Small parts and long cords may be a choking
and strangulation hazard.
Warning! Keep away from fire.
Never shelter in the sunshade during a thunderstorm, remove when not in use.
Do not attempt to put up this product in windy or rainy conditions.

Page 4 of 23
BASIC TRAMPOLINE SKILLS
Fundamental Bounce
1. Start from a standing position with your head
erect and your eyes on the frame pad.
2. Swing your arms forward and up in a circular
motion.
3. Bring your feet together and point your toes
downward while in the air.
4. Keep your feet about 30cm (12in.) apart
when landing on the bed.
Knee Drop
1. Start bouncing from a standing position,
keeping your eyes on the frame pad.
2. Land on your knees, keeping your back
straight and your body erect.
3. Come back up to an erect position.
Hand and Knee Drop
1. Start bouncing from a standing position,
keeping your eyes on the frame pad.
2. Land on the bed on your hands and knees.
3. Push with your hands and come back up to
an erect position.
Back Drop
1. Start from a low bounce and land on your
back.
2. Keep your chin forward on your chest as you
land.
3. Kick forward and up with your legs to return to
an erect position.

Page 5 of 23
Seat Drop
1. Land in a sitting position with your legs
parallel to the bed.
2. Place your hands on the bed inside your hips.
3. Push with your hands to return to an erect
position.
Front Drop
1. Start from a low bounce and land on the bed
in a prone position.
2. Keep your head up and your arms extended
forward on the bed.
3. Push with your arms to return to an erect
position.
Half Turntable
1. Start from the front drop position and push
to the left or right with your arms to begin
turning your body in the opposite direction.
2. Turn your head and shoulders toward the
direction that your body is turning.
3. Keep your back parallel to the bed and your
head up.
4. After completing a half turn, land in the front
drop position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right and swing
your arms up in the same direction.
3. Turn your hips in the same direction as your
head and arms, completing a twist.
4. Land in the seat drop position.

Page 6 of 23
1
Tools Required

Page 7 of 23
2

Assembly Instructions
Step 1:
Step 2:
Page 8 of 23
You will need the following parts to
complete section 1:
6 x Top tube with T-connector - Part A
6 x Straight leg - Part B
6 x Plastic foot cap - Part C
6 x Self-tapping screw - Part J
First we will complete one of the
sections of the trampoline frame.
Slot the narrow end of the top tube
with T-connector into another top
tube with T-connector.
2 Spring Holes on Top
4 Spring Holes on Bottom

Assembly Instructions
Step 3:
Step 4:
Page 9 of 23
This step will require 2 people
who must be wearing gloves.
Slot two of the frame sections
together as shown in the
diagram.
Important: Ensure all of the top
tubes, leg extensions and
center legs are fully inserted.

Assembly Instructions
Step 5:
Step 6:
Page 10 of 23
This step will require 2 people who
must be wearing gloves and
protective eye wear.
Lay the stitched bed (with the V-
rings) part D out inside the frame of
the trampoline.
Locate the12 V-rings on corners.
These will be at 60º to each other.
Slot one of the springs part E onto one
of the webbing V-rings as shown.
Slot the other end of the spring into one
of the spring slots in the top of the
frame.
IMPORTANT: Springs must be slotted in
the correct direction. The smaller end
will secure to the mat and larger end to
the frame. Ensure all of the springs are
fully inserted into the slots on the frame.
Facing up
With black webbing facing
down
Black webbing

Assembly Instructions
Step 7:
Step 8:
Page 11 of 23
Attach a spring to the opposite of V-ring.
IMPORTANT: You will now need to use
the spring tool (part F) to attach the
spring to the frame.
Hook the spring tool onto end of spring,
and pull until the spring can be slotted
into the spring slot on the top of the
frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the frame.
Continue to attach springs in the same sequence as above: in the middle of each
section, making sure the next spring is attached on the opposite side to even out
the tension.
Important: The stitched bed is designed like elastic to be bouncy, which means that
during construction, it may look like it won’t fit. Please note that it will stretch to the
correct size when attaching the springs, this may take some force.
The stitched bed is now fitted, and you have completed step 8.

Assembly Instructions
Step 9:
Step 10:
Page 12 of 23
This step will require 2 people.
Lay the frame pad - part G out over
the edge of the frame with the ties
facing downwards.
Align the openings in the frame pad
with the T-connector's on the frame.
The frame is fully assembled now .
You will need the following
parts.
1 x Enclosure netting - part K
2 x Black G3 poles - part L

Assembly Instructions
Step 11:
Page 13 of 23
Lay the enclosure netting out on the
trampoline.
Find the sleeves that run along the
middle of the enclosure netting.
Step 12:

Assembly Instructions
Step 13:
Page 14 of 23
Slot the thin sections on the
black G3 poles into the metal
ends so the poles become two
long sections.
Slot the Black G3 poles through
the sleeves on the middle of the
enclosure
netting.
Step 14: You will now join the two ends of the
Black G3 poles together with the fitted
pole connector, this will require two
people.
Both people hold two of the poles end
sections and walk towards each other to
bend the poles into a circle.
Please note the
poles are
Located at Middle
of enclosure.

Assembly Instructions
Step 15:
Page 15 of 23
As soon as the poles are bent enough,
insert the connectors into the socket on
the other pole (1).
Push the pin inwards (2) and fully insert
the connector.
Ensure the pin is protruding through the
slot in the socket.
Use the strap on the enclosure net to
cover the exposed pole connections.
Step 16:
You will need the following parts
6 x Top enclosure tubes - Part H
6 x Bottom enclosure tubes - Part I
6 x Self-tapping screw - Part J
You will also need a cross-head
screwdriver (not supplied)

Assembly Instructions
Step 17:
Page 16 of 23
Slot the six bottom enclosure tubes into
enclosure netting lower sleeves.
Step 18:
Slot the bottom enclosure tube into the
tubes in the T-connector visible through
the slots in the frame pad.

Assembly Instructions
Step 19:
Page 17 of 23
Slot the six top enclosure tubes into
enclosure netting upper sleeves.
Step 20: Slot the thin end of one of the
bottom enclosure tubes into the
open end of one of the top
enclosure tubes.
Align the hole in the bottom
enclosure tube with the slot in the
top enclosure tube.
Tip: It is easier to slot in from the
outside of the trampoline.

Assembly Instructions
Step 21:
Page 18 of 23
Screw one of the self tapping
screws through the slot in the top
enclosure tube and into the hole in
the bottom enclosure tube using the
cross-head screwdriver.
Repeat for the remaining enclosure
poles.
Step 22:
Find the ROD on top of enclosure
netting.
Stand on the trampoline and insert
one of the exposed sections of the
rod into a plastic grip on top of one
of the enclosure tubes.

Assembly Instructions
Step 23:
Page 19 of 23
Attach the remaining exposed
sections of the rods to the other
enclosure tubes in the order
shown in the diagram.
The enclosure net will now be
secured.
Step 24:
You will need the following parts
4 x Cords - Part M.
Tie the end of the cord around one
of the V-Ring attachments located
on the mat.
Push the end rope through the hole
at the bottom of the netting.
Important: Keep the cord tight all
times.

Assembly Instructions
Step 25:
Page 20 of 23
Slot the end of the cord through the middle
of the next V-Ring or loop along.
Now slot the end back through the net and
down through the next V-Ring. Continue
to do this until you have used up nearly all
the cord then tie the end around a V-Ring.
Tie another cord to this V-Ring and
continue until all of the net is secured.
The trampoline is now fully assembled.
Step 26: (Optional Sunshade Assembly)
Part O - Sunshade - 1 pc
Elastic - 6 pcs