AGame 166826 Owner's manual

Style #166826
16 Ft Mega Trampoline and Enclosure
Customer Service: [phone]
7:00 am to 12:00 am CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
(Made in China)
Please keep this instruction manual for future reference
Assembly Instructions
& User’s Manual

Table of Contents
Warnings 3
Tools and Parts 11
Assembly Instructions 13
Care and Maintenance 26
Warranty Information 27
Note: Before beginning assembly of product, make sure
all parts are present. Compare parts with package content
list and hardware contents. If any part is missing or
damaged, do not attempt to assemble the unit. Contact
customer service for replacement parts.
Page 2 of 27

Page 3 of 27

Page 4 of 27

Page 5 of 27

Page 6 of 27

Page 7 of 27

Page 8 of 27

Page 9 of 27

Page 10 of 27

Page 11 of 27

Page 12 of 27

Assembly Instructions
Step 1:
Step 2:
Page 13 of 27
You will need the following parts
7 x Top Tubes with T-ConnectorA –Part A
7 x Top Tubes with T-Connector B –Part B
14 x Leg Extensions –Part C
7 x Leg Centers –Part D
First we will complete one of the six
sections of the trampoline frame.
Slot the narrow end of the top tube with
T-Connector A into T-Connector B.

Assembly Instructions
Step 3:
Step 4:
Page 14 of 27
Insert the leg extensions into the
leg center.
Insert one of the leg extensions from
the complete leg into the T-Connector.

Assembly Instructions
Step 5:
Step 6:
Page 15 of 27
Important: The frame is held together
under tension so you will have to use
some force to insert certain parts.
Place one foot on the top tube and grip
the leg extension with both hands.
Pull the extension until it can be slotted
into the T-connector (1).
Slot the end of leg extension into the
T-connector (2).
Push down on the end of the leg
center to fully insert the leg extension
into the T-Connector.
You have now completed the first
frame section.
Repeat the last six steps until you
have assembled the remaining six
sections of the trampolines frame.

Assembly Instructions
Step 7:
Step 8:
Page 16 of 27
This step will require 2 people who
must be wearing gloves and protective
eyewear.
Slot two of the frame section together
as shown in the diagram.
Whilst one person holds the
assembled sections upright, the other
person can slot a third section onto
the end of the assembled sections.
Repeat for remaining four sections.
You will now need to slot the frame
together. This will take some force. The
easiest method is if the two people face
each other.
Hold the top tubes either side of the
T-Connectors and push towards each
other until the loose end of the frame
can be inserted into the T-Connector.
Important: Ensure all of the top tubes,
leg extensions, and center legs are fully
inserted.
The frame is now fully assembled.

Assembly Instructions
Step 9:
Step 10:
Page 17 of 27
This step will require two people who
must be wearing gloves and protective
eyewear.
Lay the stitched bed (with the V-Rings)
part E out inside the frame of the
trampoline with the warning labels
facing upwards.
Locate the 4 V-Rings with the yellow
stitching. These will be at 90 degrees
to each other.
Tip: There are 13 V-Rings in between
each yellow stitched V-Ring.
Slot one of the springs Part F onto one
of the color webbing V-Rings as
shown.
Slot the other end of the spring into
one of
the spring slots in the top of the frame.
IMPORTANT: Springs must be slotted
in the correct direction. The smaller
end will secure to the mat and larger
end to the frame. Ensure all of the
springs are fully inserted into the slots
on top of the frame.

Assembly Instructions
Step 11:
Step 12:
Page 18 of 27
Attach a spring to the opposite-colored
webbing V-Ring.
Important: You will now need to use the
spring tool part G to attach the spring
to the frame.
Hook the spring tool onto the end of
the spring and pull until the spring can
be slotted into the spring slot on the top
of the frame.
Important: Ensure the spring is fully
inserted into the slot on the top of the
frame.
Attach the other two yellow stitched V-
Rings to the frame using the same
method as shown in the previous two
stages.
CAUTION: Please do not install
springs continuously in one direction.
This would cause springs to over
stretch.

Assembly Instructions
Step 13:
Step 14:
Page 19 of 27
Attach four more springs to the
V-Rings in the middle of the four
attached points and then attach
them to the frame.
The stitched bed should now be
as shown in the diagram.
Continue to attach springs in the
same sequence as above in the
middle of each section, making sure
the next spring is attached on the
opposite side to even out the
tension.
Important: The stitched bed is
designed like elastic to be bouncy,
which means that during
construction it may look like it won’t
fit. Please note that it will stretch to
the correct size when attaching the
springs.
This may take some force. The
stitched bed is now secured.

Assembly Instructions
Step 15:
Step 16:
Page 20 of 27
This step will require two people.
Lay the frame pad, Part H, out over the
edge of the frame with the ties facing
downwards.
Align the openings in the frame pad with
the T-Connector B’s on the frame.
Tie the outer elastic straps on the
underside of the frame pad around the
top tubes of the frame.
Tip: Only apply a single knot when
tying the elastic straps to the frame.
The frame pad is now secured.
Warning: The trampoline MUST NOT
be used during construction.