Agilent Technologies 33210A User manual

Keysight 33210A
10 MHz Function/Arbitrary
Waveform Generator
User’s Guide
dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ [email protected] ▪ www.datatec-gruppe.de
Distributed by:
Ihr Spezialist für
Mess- und Prüfgeräte

2
Keysight 33210A at a Glance
The Keysight Technologies 33210A is a 10 MHz synthesized
function generator with built-in arbitrary waveform and pulse
capabilities.
Itscombination of bench-top and system features makes this function
generator a versatile solution for your testing requirements now and
in the future.
Convenient bench-top features
•Up to 10 standard waveforms
•Built-in 14-bit 50 MSa/s waveform capability
•Precise pulse waveform capabilities with adjustable edge time
•LCD display provides numeric and graphical views
•Easy-to-use knob and numeric keypad
•Instrument state storage with user-defined names
•Portable, ruggedized case with non-skid feet
Flexible system features
•Four optional downloadable 8K-point arbitrary waveform
memories (Option 002)
•GPIB (IEEE-488), USB, and LAN remote interfaces are standard
•LXI Class C Compliant
•SCPI (Standard Commands for Programmable Instruments) compatibility
Note: Unless otherwise indicated, this manual applies to all Serial Numbers.
33210A users guide.book Page 2 Wednesday, July 16, 2008 11:16 AM

3
The Front Panel at a Glance
Note: To get context-sensitive help on any front-panel key or menu softkey,
press and hold down that key.
1Graph Mode/Local Key
2On/Off Switch
3Modulation/Sweep/Burst Keys
4State Storage Menu Key
5Utility Menu Key
6Help Menu Key
7Menu Operation Softkeys
8Waveform Selection Keys
9Manual Trigger Key (used for
Sweep and Burst only)
10 Output Enable/Disable Key
11 Knob
12 Cursor Keys
13 Sync Connector
14 Output Connector
33210A users guide.book Page 3 Wednesday, July 16, 2008 11:16 AM

4
The Front-Panel Display at a Glance
Menu Mode
Trigger OutputMode
Numeric
Readout
Information Information StatusUnits
Display
Icon
Softkey Labels
Graph Mode
To enter or exit the Graph Mode, press the key.
In Graph Mode, only one parameter label
Signal
Parameter
Name Parameter
Value
Ground
is displayed for each key at one time.
33210A users guide.book Page 4 Wednesday, July 16, 2008 11:16 AM

5
Front-Panel Number Entry
You can enter numbers from the front-panel using one of two methods.
Use the knob and cursor keys to modify the displayed number.
1. Use the keys below the knob to move the cursor left or right.
2. Rotate the knob to change a digit (clockwise to increase).
Use the keypad to enter numbers and the softkeys to select units.
1. Key in a value as you would on a typical calculator.
2. Select a unit to enter the value.
33210A users guide.book Page 5 Wednesday, July 16, 2008 11:16 AM

6
The Rear Panel at a Glance
Note: The External and Internal 10 MHz Reference Terminals (1 and 2,
above) are present only if Option 001, External Timebase Reference, is
installed. Otherwise, the holes for these connectors are plugged.
WARNING For protection from electrical shock, the power cord ground must not be
defeated. If only a two-contact electrical outlet is available, connect the
instrument’s chassis ground screw (see above) to a good earth ground.
1 External 10 MHz Reference Input Terminal
(Option 001 only).
2 Internal 10 MHz Reference Output Terminal
(Option 001 only).
3External Modulation Input Terminal
4Input:
External Trigger/Burst Gate
Output: Trigger Output
5USB Interface Connector
6LAN Interface Connector
7GPIB Interface Connector
8Chassis Ground
Use the menu to:
• Select the GPIB address (see chapter 2).
• Set the network parameters for the LAN interface (see chapter 2).
• Display the current network parameters (see chapter 2).
33210A users guide.book Page 6 Wednesday, July 16, 2008 11:16 AM

7
In This Book
Quick Start Chapter 1 prepares the function generator for use and
helps you get familiar with a few of its front-panel features.
Front-Panel Menu Operation Chapter 2 introduces you to the front-
panel menu and describes some of the function generator’s menu features.
Features and Functions Chapter 3 gives a detailed description of the
function generator’s capabilities and operation. You will find this chapter
useful whether you are operating the function generator from the front
panel or over the remote interface.
Remote Interface Reference Chapter 4 contains reference information
to help you program the function generator over the remote interface.
Error Messages Chapter 5 lists the error messages that may appear
as you are working with the function generator. Each listing contains
information to help you diagnose and solve the problem.
Application Programs Chapter 6 contains several remote interface
application programs to help you develop programs for your application.
Tutorial Chapter 7 discusses the fundamentals of signal generation
and modulation techniques.
Specifications Chapter 8 lists the function generator’s specifications.
33210A users guide.book Page 7 Wednesday, July 16, 2008 11:16 AM

8
You can contact Keysight Technologies at one of the following
telephone numbers for warranty, service, or technical support
information.
In the United States:[phone]
In Europe:31 20 547 2111
In Japan:0120-421-345
Or use our Web link for information on contacting Keysight worldwide.
www.keysight.com/find/assist
OrcontactyourKeysight TechnologiesRepresentative.
33210A users guide.bookPage8 Wednesday, July 16, 2008 11:16 AM