AGILTRON NanoSpeed User manual

The NS switch driver provides a convenient way to use the NS series electro-optical
switches, which act as a pure capacitive load. Each driver is tuned to a specific
device mounted on the PCB.To operate, the customer only needs to plug in the
accompanying DC power supply and input a control signal through the golden SMA
connector. The switch will be activated as the input voltage exceeds 3V with less
than 1µA draw, compatible with 3.3V CMOS/TTL . We produce boards to control
multiple NS switches with individual SMA connectors. No computer-based control
software is available for such a high-speed operation.
Features
•High speed
•High repetition
•High output voltage
•Wide input voltage range
•TTL/CMOS control
•Push-Pull output design
• Low power consumption
•Compact and low cost
Applications
•Optical Switch
•EO device driver
Product Description
Performance Specifications
100 kHz Repetition Rate NanoSpeedTM
Switch Driver
15 Presidential Way, Woburn, MA 01801 Tel: [phone] Fax: [phone]
www.agiltron.com
Revised on 12/28/22
Specs
Min
Typical
Max
Unit
Rise Time (Tr)[1]
85
100
ns
Fall Time (Tf)[2]
85
100
ns
Repetition Rate
DC
100
kHz
Pulse Width
1.0
s
Control Input (TTL pulse)
0
5
V
Power Consumption
5
W
Power Current
0.08
0.4
A
Power Supply
12
V
Operating Temperature
-5
70
ºC
Storage Temperature
-40
80
ºC
Electrical Connector
SMA
Board Size
3.5(L)x1.25(W)
Inch
Note:
[1]: Optic Intensity Change from 10% to 90% intuits;
[2]: Optic Intensity Change from 90% to 10% intuits;
[3]: Switch Speed (Rise): Duration from begin of electronic signal to end of optic intensity change;
[4]: Switch Speed (Fall): Duration from begin of electronic signal to end of optic intensity change.
(Protected by U.S. patent 7,403,677B1 and pending patents)
Warning: Control Signal >5.5V Will Damage the Board

15 Presidential Way, Woburn, MA 01801 Tel: [phone] Fax: [phone]
www.agiltron.com
Response Measurement
100 kHz Repetition Rate
NanoSpeedTM Switch Driver
Dimensions (mm)
*Product dimensions may change without notice. This is sometimes required for non-standard specifications.

15 Presidential Way, Woburn, MA 01801 Tel: [phone] Fax: [phone]
www.agiltron.com
100 kHz Repetition Rate
NanoSpeedTM Switch Driver
Power Connector
P/N: SC1313-ND
Power Barrel Connector Jack 2.00mm ID (0.079"),
5.50mm OD (0.217") Through Hole, Right Angle 12V Wall Plug DC Power Supply Interface
TTL Driver Interface (Our Circuit Diagram)
4 5
U1-A 0.1uF
EL7222
6
3
2 7
Port
Port
U1 - B
R1t
10K
EL7222
5V
C1
TTL or COMS Signal
(H: >2.4V; Recommend: 5V)
(L: <0.8V)

15 Presidential Way, Woburn, MA 01801 Tel: [phone] Fax: [phone]
www.agiltron.com
100 kHz Repetition Rate
NanoSpeedTM Switch Driver
1. Connect a control signal to the SMA connector on the PCB.
2. Attach the accompanied power supply (typically a wall-pluggable unit).
3. The device should then function properly.
Note: Do not alter device factory settings.
Operation Manual
Ordering Information
1□□ 2 6 1 □1□
Prefix
Switch
Type Function
Latching or not
Repeat
rate [1] Footprint # of Switch Control Mode
DC supply
SWDR-
NS Switch
=1
1x1, 1x2, 2x1,
2x2 switches = 1a
Non
-latching =
2
100
kHz =
6
Standard = 1
1 switch=1
TTL=1
12VDC =1
Special = 0
2 switches=2
USB =2
5VDC
[2]
=2
1x4, 4x1 switches
= 4a
3 switches=3
RS232 =3
Special =0
N switches=N
TTL & USB = 4
Special=00
Special=0
RS232 & USB = 5
Special=0
[1]: The repeat rate is defined for TTL control interface only
[2]: 5V DC supply may not be available for certain switch. Please have a consultant with sales manager