Agora Fast2 User manual

Page 1 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Fast2 User’s manual
Fast2 Firmware version 1.10.16
Agora Controller Software version 1.2.X
AGORA
43 Avenue de Châtellerault
86440 MIGNE AUXANCES
FRANCE
France
web site: www.agora-network.fr
In accordance with the company policy of continuous upgrade and products improvement, specifications and functions are subject to change
without prior notice. This document was true at the time of writing, please contact our local distributor or visit our website to date with the
latest updated versions.

Page 2 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
²
IMPORTANT SAFETY INSTRUCTIONS
This symbol significates the presence of uninsulated dangerous voltage within the
product’s enclosure that may be sufficient to constitute a risk of electric shock for persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance instructions in the literature joined to this product, particularly in this document.
1 Read these instructions.
2 Take in consideration.
3 Follow all instructions.
5 Do not use this device near water.
6 Clean only with a dry cloth
7 Do not close any ventilation or air-cooling reserved space.
8 Install in accordance with the manufacturer’s instructions.
9 Do not install near any heat source as radiators, or other devices that produce heat.
10 Do not remove the grounding electrical connection. This device must be powered with
three ways IEC 13 shucko (L/N/G).
11 Only use fixations and accessories specified by the manufacturer.
12 Unplug this device during maintenance service and when one of its hoods is removed.
13 Unplug this device when unused for long periods.
14 Use one or two twice power cords to disconnect the device from the mains. The device is
not equipped of main power switch.
15 To reduce the risk of electric shock or fire, do not expose this device to rain, water, or any
liquids and ensure that no objects which contains liquids are placed on the equipment.

Page 3 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
EC DECLARATION OF CONFORMITY
1. Product identification: FAST2-HRPS-OPTKMM-OPTKSM
2. Name and address of the manufacturer or his authorized representative: AGORA SAS
43, Avenue de Châtellerault – 86440 MIGNE-AUXANCES - FRANCE
3. This declaration of conformity is issued under the sole responsibility of the manufacturer:
AGORA SAS
4. Object of the declaration:
•Fast2
•HDMM/OC: Optical fiber DUAL OpticalCon NEUTRIK - Multimode - on front
•HDSM/OC: Optical fiber DUAL OpticalCon NEUTRIK - Singlemode - on front
•HQMM/OC: Optical fiber QUAD OpticalCon NEUTRIK - Multimode - on front + recovery of fiber 3/4
on the rear panel OC DUAL
•HQMM/OC: Optical fiber QUAD OpticalCon NEUTRIK - Singlemode - on front + recovery of fiber 3/4
on the rear panel OC DUAL
•HRPS: Redundant Power supply option for Fast series

Page 4 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
5. The object of the declaration described in point 4 is in conformity with the relevant Union
harmonization legislation:
•Low voltage Directive 2014/35/EU of 26 February 2014
•Electromagnetic Compatibility Directive 2014/30/EU of 14 October 2014
•Radio Equipment Directive (RED), 2014/53/EU of 22 May 2014
•ROHS2 Directive 2011/65/EU of 7 January 2011
6. References to the relevant harmonized standards used, or references to the
specifications in relation to which conformity is declared:
•2004/108/EC: EMC Directive
•2006/95/EC: Low voltage Directive
Signed for and on behalf of:
MIGNE-AUXANCES – FRANCE – March 31st, 2021
David ROCHER, CEO

Page 5 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
END USER LICENCE AGREEMMENT
The following are the license agreements applicable for Fast™ equipment and software suite.
IMPORTANT – Please read this document carefully before using the Fast™ and Agora™ products. This agreement
governs you for use of software installed on Ghost™ engines or on other machine, as well as other software that we
provide for installation of this product. This Ghost™ product range will not operate according to this document
without software list and instructions described below.
THIS LICENSE STATES THE TERMS AND CONDITIONS UPON WHICH AGORA COMPAGNY OFFERS TO LICENSE THE H1
EMBEDED PROGRAMS (ALSO CALLED “FIRMWARE”) AND USER COMPUTER INSTALLED PROGRAMS (ALSO CALLED
“SOFTWARE”) WICH HAS BEEN INSTALLED BY OR FOR WICH IT IS PROVIDED. BY USING THIS PRODUCT, YOU WILL BE
AGREEING TO BECOME BOUND BY TERMS OF THIS LICENSE. IF YOU DO NOT AGREE TO THE TERMS AND
CONDITIONS OF THIS LICENSE? PLEASE DO NOT USE THIS PRODUCT AND RETUR IT TO THE PLACE WHERE YOU
OBBTAINED IT FOR A FULL REFUND. YOU AGREE TO NOTIFY ANY PERSONS YOU PERMIT TO OPERATE THIS PRODUCT
OF THE TERMS OF THIS LICENSE.
The H1™ Controller software is licensed, delivered for free to use only under the terms of this license. The Company
reserves all rights not expressly granted to you. The Company retains ownership of all copies of the Software and
the firmware, and all proprietary parts of it, including files stored in the product.
1. License: Subject to the terms and conditions of this agreement, the Company credit you and other persons
you permit to operate the product, a personal, limited, non-exclusive and non-transferable license to use
the Software only on Windows OS licensed computers, and the firmware only on the single product in
which it has been installed.
2. Restrictions: The Agora Controller software package and the joined written materials and documents are
copyrighted and contain trade secrets and other proprietary matter, including confidential information
relating to the specifications and performance characteristics of this product. Save for such elements
described in the chapter 5 as may be licensed to the Company, all rights to copyrights, trademarks and
secrets, or any modifications of this Product are owned by the Company. Unauthorized use or copying of
the Company’s proprietary Software, or any portion, or copying of those written materials is prohibited.
You don’t may create, transfer, market or distribute whole or partial copies of the Company’s proprietary
Software to others or duplicate, rent, lease or loan that Software except that you may transfer that
installed in this product in conjunction with the sale, transfer, lease or rent of the product and subject at all
times to this license.
YOU MAY NOT REVERSE ENGINEER, DECOMPILE, DISASSEMBLE, EXTRACT OR SEPARATE
OUT, MODIFY, ADAPT OR TRANSLATE THE SOFTWARE, DERIVE THE SOFTWARE SOURCE
CODE ORE DREATE DERIVED APPLICATIONS OR ANY ACCOMPANYING WRITTEN
MATERIALS BASED ON THE SOFTWARE.
In the case you violate any term of this license, all rights granted will be automatically and definitively
terminate and you must stop using this Software and destroy any copies.
3. Limited Warranty: Subject to your installation of any Software updates issued by the Company as
described herein, and the condition below, the Company warrants that the Software will operate in
compliance with the Software's material specifications and documentation for a period of 120 days from
your purchase of this Product. The Software is provided "as is" and the Company does not warrant that the
operation of the Software will meet your requirements or operate free from error. To the greatest extent

Page 6 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
permissible by law, the Company DISCLAIMS ALL WARRANTIES AND CONDITIONS, EITHER EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
NON-INFRINGEMENT OF THIRD-PARTY RIGHTS OR CAPABILITY OF CORRECTLY PROCESSING PROVIDING
AND/OR RECEIVING DATE INFORMATION. You understand that the Company may update or revise the
Software but in so doing incurs no obligation to furnish such updates to you. However, the Company may
in its discretion make updates available from time to time upon such terms and conditions as it shall
determine. It is a condition of the above warranty that you install any such Software updates, as may be
issued from time to time by the Company for the Software, in accordance with the Company's instructions,
and if you do not do so such warranty will cease to apply. You may view current Software updates at
http://www.agora-network.fr.
4. Limited Liability:THE ENTIRE RISK ARISING OUT OF YOUR USE OR PERFORMANCE OF THE SOFTWARE
REMAINS WITH YOU. THE LIABILITY OF THE COMPANY FOR ANY CLAIMS ARISING OUT OF THIS LICENCE
AND/OR BASED UPON THE SOFTWARE, REGARDLESS OF THE FORM OF ACTION, AND INCLUDING WORK
STOP, PRODUCT MALFUNCTION OR ANY OTHER COMMERCIAL LOSS OR DAMAGE, SHALL NOT EXCEED THE
COST OF THE LICENCE FEE FOR THE SOFTWARE OR THE COST OF THIS PRODUCT. SUBJECT TO THE
PROVISIONS OF APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY LOSS OF DATA,
LOST OPPORTUNITY OR PROFITS, COST OF COVER OR SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT
DAMAGES, EVEN IF YOU ADVISE THE COMPANY OF THE POSSIBILITY OF SUCH DAMAGES. THIS IS A
FUNDAMENTAL TERM OF THIS AGREEMENT AND YOU ACKNOWLEDGE THAT THE AMOUNT YOU PAID FOR
THE SOFTWARE AND/OR THE PRODUCT REFLECTS THIS ALLOCATION OF RISK. NOTHING IN THIS
PARAGRAPH PURPORTS TO EXCLUDE OR LIMIT THE COMPANY'S LIABILITY FOR DEATH OR PERSONAL
INJURY CAUSED BY NEGLIGENCE OR ANY OTHER LIABILITY WHICH CANNOT BE EXCLUDED OR LIMITED BY
LAW.
5. Third-Party Programs: As referred to herein, the term "Software" refers only to proprietary Agora Controller,
owned by the Company that has been provided to you for installation on, or already installed in, a Product.
In addition to the Software, you may have also been provided, at no additional charge, with a version of the
TP Link™ switch embedded OS installed in flash memories of the Product’s mother boards. Mother board
has its own applicable end user license agreement; you can keep a copy by contacting support@agora-
audio.com
6. Exit of agreement. This License will terminate immediately if you violate any of the License terms. Upon
termination you must discontinue use of the Software, and either destroy, erase or return to Company all
copies of the Software in your possession, custody or control, including those in or on the Product.
7. General terms. This License constitutes the entire agreement between you and the Company with respect
to this Software and save in the case of fraud, supersedes any other communication (including advertising).
Company reserves all rights not expressly granted to you in this license. If any provision of this License is
held unenforceable, that provision shall be enforced to the maximum extent permissible to give effect the
intent of this License, and the remainder of this License shall continue in full force and effect. This License
shall be governed by French law and the Courts of France will have exclusive jurisdiction to hear and decide
any conflict concerning it or its formation. No breach by you of any provision of this License shall be waived
or discharged except with the express written consent of the Company and no failure or delay by the
Company to exercise any of its rights under this License shall operate as a waiver thereof and no single or
partial exercise of any such right shall prevent any other or further exercise of that or any other right. You
acknowledge that the Company could be irreparably damaged if the terms of this License were not
specifically enforced and agree that the Company may seek appropriate equitable remedies with respect to
breaches of this License, including injunctive relief, in addition to such other remedies as the Company may
otherwise have available to it under applicable laws.

Page 7 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
CONTENTS
Chapter 1 Getting Started
Unpacking
Installation
Chapter 2 General information
Chapter 3 Fast2 architecture
Chapter 4 Configure Fast2
Chapter 5 Fast2 topologies examples
APPENDIX Technical specifications

Page 8 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
CHAPTER 1: Getting Started
Before installing, setting up or operating this equipment, make sure you have read and fully understand all of the
“IMPORTANT SAFETY INSTRUCTIONS” at the end of this document.
Important: You must set up the IP address and netmask of your computer (PC Windows 10 32/64 bits or MAC OS X)
before using it for the first time.
Unpacking
Carefully unpack your Fast equipment package. Then, inspect the device for any signs of damage that may have
occurred during transit and notify the courier immediately if you discover any. Please retain the original packing in
case you should need to return the equipment to the manufacturer or supplier, or transport or ship the unit later.
Installation
When installing the unit, take the following into consideration.
• Do not install the equipment in places of poor ventilation.
• Do not install this equipment in a location subjected to excessive heat, dust, or mechanical vibration.
Allow for adequate ventilation around the equipment, making sure that its vents are not obstructed. To prevent
excessive heating of the equipment, avoid mounting it directly above power amplifiers or other devices that radiate
significant amounts of heat, such as radiators and heaters. Keep the equipment out of direct sunlight.
• This 1U rack unit is designed for mounting in any 19” EIA standard rack. . Four rack-mount holes in the front panel
are provided for rack mounting and are designed to fully support the weight of the unit in the rack. Avoid over-
tightening the rackmount screws, as this could damage the front panel.
Handling the Equipment
Completely isolate the equipment electrically and disconnect all cables from the equipment before moving it.
When lifting or moving the equipment, always take its size and weight into consideration.
EMC Regulatory Statements
Europe CE (EN55022)
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
U.S.A.FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference
to radio communications. Operation of this equipment in a residential area may cause interference in which case
the user will be required to correct the interference at his own expense.
Canada
This product complies with Class A Canadian EMC requirements. CAN ICES-3 (A) / NMB-3 (A)

Page 9 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Changes or modifications not expressly approved by Agora could void the user’s authority to operate the
equipment.
Australia/New Zealand
This product complies with Australia/New Zealand EMC Class A requirements.
Electric fields
Caution: In accordance with Part 15 of the FCC Rules & Regulations, “… changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.”
These are safety class I products and have protective earth terminals. There must be an uninterruptible safety earth
ground from the main power source to the product’s input wiring terminals, power cord, or supplied power cord
set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has
been restored.
For LAN cable grounding:
■If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are
securely interconnected.
■LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the
electrical utilities power grid). Handle exposed metal components of the network with caution.
In accordance with EN 60950-1 the base of power socket must be installed near the equipment and must be free of
access for the disconnection of the power supply in case of danger.
About this manual
This is the operator manual for the Fast2 unit and the Agora Controller. It is intended to help get your units installed
and in operation as quickly as possible by giving you unpacking, installation, connection, configuration and setting
up instructions.
To help familiarize you with the units, there is a description of the front and rear panels, along with easy-to-follow
user instructions.
Trademarks
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other
countries.
Apple and OS X are registered trademarks of Apple Corporation in the United States and other countries.
OpticalCon is registered trademark of Neutrik Group in Liechtenstein
SmartBeam is registered trademark of Klotz GmbH in Germany

Page 10 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Chapter 2: General Information
Thank you for purchasing an Agora Fast2. The Fast2 System is a user-friendly, high-performance, dual network
switch especially designed to meet the requirements of AV IT professional’s applications.
GHOST, FAST2 and H1 units complement each other. All these devices can coexist in the same network topology.
Your Fast2 was developed by Agora to offer AV professionals a high-performance dual network switch equipment,
designed to provide no-compromise network builder and an easy-to-use interface to build the most complex
networked system in a minimum of time.
All this is backed up, of course, by five years warranty for all materials and accessories.
Finally, enjoy your Fast2 dual network switch system!
About
The Fast2 System provides:
•One fully configurable “Primary” switch with by default:
-5 User ports (4 Ethercon™ on the front panel (P1 to P4) and 1 Ethercon™ on the rear panel (P5)
-1 Control Port on the rear panel (P6).
-2 Transmit ports for units interconnexion:
T1: Optional Gigabit 1000BaseX OpticalCon™ or SmartBeam™ Duo ports
in Single mode or Multimode (chosen at purchase)
T3: Gigabit Ethercon™ port on the front panel.
•One fully configurable “Secondary” switch with by default:
-6 User ports (4 Ethercon™ on the front panel (S1 to S4) and 2 Ethercon™ on the rear panel (S5,S6)
-2 Transmit ports for units interconnexion:
T2: Optional Gigabit 1000BaseX OpticalCon™ Duo ports
in Single mode or Multimode (chosen at purchase)
T4: Gigabit Ethercon™ port on the front panel.
•One configurable Gigabit ethernet internal link between Primary and Secondary switches.
•250 User Groups manageable by Agora Controller software (from 1.10.16 firmware)
•A Status LED and one Traffic LED is appointed on each port. The front panel User ports are appointed of an ID
LED fully manageable in the Agora Controller.
•Port roles:
All ports have fixed roles (User or Transmit), except:
S5 and S6 ports: can be either User or Transmit ports.
P5 and P6 port: can be either User, Transmit or Control port.

Page 11 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
The units can be equipped in option by a redundant power supply unit.
Optical fiber ports must be connected in Single mode OR Multimode.
UNDER NO CIRCUMSTANCES A MULTIMODE PORT CAN BE CONNECTED TO A SINGLE MODE.
OpticalQuad™ option (chosen at purchase): Unused dual fibers are reported to the Back panel on an OpticalCon Duo
port.
See Diagram below:

Page 12 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Chapter 3: Fast2 architecture
Fig.1 External configuration
Fig.2 Internal configuration

Page 13 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Chapter 4: Configure Fast2
Connect your computer to a Control Port. P6 is the default control port
For general connection and configuration of Agora devices, please refer to the Agora Controller
User’s manual at https://www.ghost-network.com/support-downloads/
FNCT Button / Device LED
Fixed Green LED: Normal status, User Ports ID LEDs show User Groups colours.
Flashing Green LED: Identify device with Agora Controller
Flashing Blue LED: Service mode during Firmware Upgrade
From Fixed Green LED:
•Press FNCT Button once:
Yellow LED: User Ports Status LEDs show Port speed:
None = 10Mbps, Flashing= 100Mbps, Fixed=1000Mbps
•Press FNCT Button twice:
Red LED: not implemented
•Long Press FNCT Button TWICE:
White flashing LED: Press once to Reset the IP address at 192.168.1.101/24
Fig.3 Fast2 in Agora Controller

Page 14 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Fast2 Internal Link mode
Fast2 has to considered differently from Ghost and H series as it is a “dual switch” device.
The Master Controller Unit (MCU) is in charge of Function Button and DeviceLED, Ports ID/Status/Traffic LEDS
The internal gigabit Ethernet link has 3 possible configuration modes:
•OPEN
Internal link between Primary and Secondary switch is deactivated.
•DUAL
Only Ctrl Group (VLAN 256) is transmitted between Primary and Secondary switches for Software Control
•SINGLE
All User Groups (All VLANs) are transmitted between Primary and Secondary switches

Page 15 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Important notes:
•IP addresses:
The Secondary IP address is automatically configured from the Primary IP address adding 1 to the last Byte.
i.e Primary IP address: 192.168.1.101/24 gives Secondary IP address: 192.168.1.102/24
•Agora Controller DO NOT allow control of an “half-discovered” Fast2. Both Primary and Secondary have to
be discovered among the VLAN 256.
When OPEN mode is selected, the Secondary unit CANNOT be not directly controlled from the Primary unit
of the same device.
In this case the Secondary unit has to be reached by its transmit ports from another Agora device (Ghost,
H1, Fast in Dual or Single mode)
Tip: an Ethernet cable can also be plugged between T3 and T4 to simulate Dual mode.
•Multiple DUAL and/or SINGLE Fast2 topologies have to be used with care as the internal links between
Primary and Secondary units participate in RSTP protocol.
Please refer to the technical note “Rapid Spanning Tree Protocol: Best practice for redundancy on Ethernet
AV networks” and see also Chapter 5 for topologies examples.
Fig.3Full Open mode
Agora Controller cannot control Secondary units.
Devices stay Offline (Primary status)

Page 16 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Chapter 5: Fast2 topologies examples
Fig.4Only one Dual or Single device: Valid loop-free topology
Ghost and H1 series can be considered as a Single Device

Page 17 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Fig.5Only one Dual or Single device: Valid loop-free topology
Ghost and H1 series can be considered as a Single Device

Page 18 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Fig.6Multiple Dual and/or Single devices: Looped topology
RSTP configuration has to be considered in order to define the active and alternate links

Page 19 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept
Fig.7Fast2 Single mode
Example of Redundancy management for AV & Remote protocols
Dante “seamless” redundancy :
•Dante Primary is assigned on Primary units
•Dante Secondary is assigned on Secondary units
•Redundancy is guaranteed by Dante end points
Other protocols redundancy:
•Guaranteed by RSTP (few seconds convergence)
•Adjust Bridge priorities in order to force the Fast2 B internal link to be deactivated.
For further details, see Technical Note “Rapid Spanning Tree Protocol : Best practice for
redundancy on Ethernet AV networks”

Page 20 | 21
Fast2 User’s Manual
Rev 1.0 – 2022 Sept