aidapt VM310A Manual

Fixing and Maintenance Instructions
This le is available to view and download as a PDF at
www.aidapt.co.uk. Sight impaired customers can use a free
PDF Reader (such as adobe.com/reader) to zoom in and
increase the text size for improved readability.
VM310A
Vibration Alarm Clock

INTRODUCTION
Thank you for purchasing the Vibration Alarm Clock.
These instructions should be read carefully and left with the user of the product for
future reference.
INTENDED USE
The Aidapt Vibration Alarm Clock is ideal for those with hearing impairments; or simply
those who oversleep. It has a strong vibration, loud alarm and built in back light. It can
easily be placed under a pillow and secured by using the provided strap with clip. It also
features a built in stand so it can be used as a desktop clock.
FEATURES
• Portable and suitable for travel • LCD display • Features a snooze button
BEFORE USE
Carefully remove all packaging and check the product thoroughly for damage or obvious
faults. Avoid using any knives or other sharp instruments as this may damage the surface of
the product.
ASSEMBLY INSTRUCTIONS
Buzzer
Alarm 2
On/O
Alarm 1
On/O
Buzz + Vib
Buzz
Vibration
Snooze
Time
Min Set
Hour Set
Battery
Cover
Stand
Test
Alarm
LCD Display
1. Inserting Batteries
Open the battery cover, insert
main batteries (2xAA/not
supplied) with correct polarity
as indicated in g. 1 . Also
insert backup battery (CR2032/
supplied) with correct
polarity as indicated in g. 1
Please note the back-up battery will maintain the clock running, however, the alarm sound and vibration
will not work without the main batteries (2xAA).
g. 1
Main
Battery
Backup
Battery

2. Adjusting Local Time (T1)
• Press the ‘Time’ button for 3 seconds until the time starts blinking.
• Press the ‘Hour’ button to adjust the hour
• Press the ‘Minute’button to adjust the minute
• Press the ‘Snooze’ button to swap 12/24 hour clock, once selected it will automatically
revert to set time
• Press the ‘Time’ button again to exit the time set mode
3. Adjusting Alternate Time (T2)
• Press the ‘Time’ button to swap display to show the second time (T2)
• Press and hold the ‘Time’ button for 3 seconds, or until the hour digits start blinking
• Press the ‘Hour’ button to adjust the hour.
• Please note: You cannot adjust the minute digits on T2, only the hour
• Press the ‘Time’ button again to exit the time set mode
3. Swap between Local time (T1) and second time zone (T2)
• Press the ‘Time’ button to toggle between the Local time (T1) and the second (T2). The
digital display will show T1 or T2. Please note the alarm will activate according to the
display time.
4. Set Alarm Time (AL1/AL2)
• Press the ‘Alarm’button to swap the display to show the alarm time AL1/AL2
• Press and hold the ‘Alarm’button for 3 seconds until the alarm time starts blinking AL1/
AL2
• Press the ‘Hour’ button to adjust the hour of the alarm time
• Press the ‘Minute’button to adjust the minute of the alarm time
• Press the ‘Time’ Button again to exit the time set mode
5. Display Alarm Time (AL1/AL2)
• Press the ‘Alarm’button to swap alarm digital display to show the alarm time AL1/AL2.
Press ‘Time’ button again to display desired time (T1/T2).
6. Back Light
• Press the ‘Snooze/Stop’ button once to turn on the back light. Back light will stay on for
approximately 20 seconds
7. Test
• Press and hold the ‘Test’ button to test the buzzer
8. Alarm on/o
• Slide the alarm 1 or alarm 2
switch to on or o position to
turn the alarm on or o, see g. 2
g. 2
A
l
a
r
m
1
V
i
b
A
l
a
r
m
2

9. Vibration (Vib) / Buzzer (Buzz) / Buzzer + Vibration (BuzzVib)
• Slide the switch to select the desired wakeup method
10. Snooze
• Press the ‘Snooze’ button to delay the alarm by 10 minutes, you shall see a ‘z’ on the
digital display
• During this 10 minute delay, pressing ‘snooze’again will turn the alarm o for that
day (the alarm will continue to sound at the same time every day, unless you turn the
switch (AL1/AL2) o
11. Using as a Desktop Clock
• If you wish to use your alarm clock as a desktop clock, ip open the stand in order to sit
your clock on the table (see g. 3)
SERVICE WARRANTY
Aidapt Bathrooms Ltd guarantees the product free from defects in material and
workmanship for a period of one year.
Should this product be operated under conditions other than those recommended, or any
attempts made to service or modify the product, then the warranty is rendered void.
The product you buy may dier slightly from illustrations. This warranty is in addition to,
and does not aect your statutory rights.
Our guarantee is administered by our retailers.
If your product arrives damaged, you must contact the retailer from whom you bought it.
The retailers contact details will be on the invoice that arrived with the product, or on the
email you received when you placed the order. Do not contact Aidapt Bathrooms Ltd, only
your retailer can arrange a replacement or refund.
If your product fails within the guarantee period, please contact the retailer from whom
you bought it.
If you have received your product and require technical help, please call our help desk on
01744 745 000
A copy of the instructions leaet can be downloaded from our website.
TECHNICAL INFORMATION
Width .............................................................. 86mm
Length ............................................................ 30mm
Height............................................................. 86mm
Net Weight....................................................... 160g
g. 3
Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX
Web: www.aidapt.com | Email: [email protected].uk