AIR GAP AG250-003 User manual

TAP-A-TAP™
COLD/HOT POTABLE
WATER ELECTRICAL
VALVE
Model:
Part No.
AG250-003
Doc. # 400-0787-003
500 Jefferson Street, Placentia, California 92870 USA • 949-955-3928 • Email: [email protected]
Copyright 2019 AIR GAP INTERNATIONAL
AG250-003 Valve is battery operated ( AA type, 4pcs included)
Change battery instruction.
CAUTION:
AG250-003
1.
VALVE TO PEDAL CONNECTION (SEE FIG. 2)
FIG. 2
Connect 3.5mm Female Cable from the valve to the 3.5mm Male
Cable on the pedal. See pedal installation on manual for the pedal.
Disconnect cable connection between
battery pack and valve.
1.
Remove Battery pack from valve body.
2.
Open battery pack by removing a screw
on the bottom of battery pack.
3.
Replace batteries, following "+" and
"_" sign.
4.
Close battery pack by installing the
screw. Install battery pack into valve unit
in original place.Squeeze metal tab if
needed to hold battery pack in place.
5.
Connect 2.5 mm power plug cable
from battery pack to 2.5mm power
jack on the valve body (see FIG 3.)
6.
Battery pack
2.5 mm
Power Plug
cable from
battery pack
Placentia, California

2 – #8 Mounting Screws
1 – Hot/Cold Water Valve
Installation Procedures
LIST OF PARTS ENCLOSED
The AG250-003, in combination with
AG250 series foot pedals, provides
hands free faucet operation. Pedals are
ordered separately. Select from the
following three foot pedals:
AG250-403, AG250-503 or AG250-603.
Please read the instructions once through before starting.
VALVE INSTALLATION INSTRUCTIONS
-OVER-
FIG. 1
2 – Block and Brick Wall Anchors
2 – 30" Water Supply Hoses, connector 1/2" FIP x 1/2" FIP
2 – Drywall Twist In Lock Anchors
Dual Electiical
Water Valve
1/2" Inlet Port
x2
#8 Mounting
Screws
x2
Anchor
(shown drywall
type)
x2
To Water Supply
To Faucet
Connect to
the Pedal
Before mounting the AG250-003 make sure that water is turned off.
Disconnect hoses (hot and cold water) between the faucet and
water supply.
1.
Mount the AG250-003 valve to the wall in shown on FIG.1 position .
Use supplied screws and anchors to mount valve. Install them in
mounting openings on opposite corner of the unit (use 6mm/ 1/4"
drill).
2.
Connect valve's outlet ports to the faucet using provided 30" hoses.
3.
Connect the water supply hoses to the inlet ports .
4.
While connecting hoses to the valve, use minimum force to tighten
the nut in order to prevent port adapter from rotating.
5.
Connect 3.5mm Female cable from the valve body to the pedal
(see Fig. 1 and Fig. 2).
6.
Turn on water supply and check for leakage.
7.
Press the pedal, open the faucet, and adjust it to the desired water
temperature and flow rate.
8.
As long as the pedal is depressed, water will flow from the faucet.
9.
When the pedal is released, the water flow stops.
10.
AG250-403 AG250-503 AG250-603
AG250 Series Foot Pedals
Kitchen pedal with
constant flow lock Kitchen / bathroom pedal Kitchen / bathroom floor mounted pedal
1/2" Outlet Port
x2
Connect 2.5 mm power plug cable from the battery pack to the
2.5mm power jack on the valve body (see FIG 1.)
6.
Battery pack
AA battery
included
x4
2.5 mm
Power Plug
cable from
battery pack
2.5 mm
Power Jack

TAP-A-FLOW™
FLOOR PEDAL,
STAINLESS STEEL FINISH
(battery operated)
Placentia, California
Model:
Part No.
AG250-603
Doc. # 400-0792-001
500 Jefferson Street, Placentia, California 92870 USA • 949-955-3928 • Email: [email protected]
Copyright 2019 AIR GAP INTERNATIONAL
AG250-603
Press on pedal, open the faucet, and adjust it to the desired water
temperature and flow rate.
3.
As long as the pedal is pressed, water will flow from the faucet.
When the pedal is released, the water flow stops.

1 – Floor pedal
Installation Procedures
AG250-603
LIST OF PARTS ENCLOSED
The AG250-603, in combination with
AG250-003 valve, provides hands-free
faucet operation. Valve is ordered
separately.
Please read the instructions once through before starting.
PEDAL INSTALLATION INSTRUCTIONS
-OVER-
1.
FIG. 1
2 – #6x1 mounting screws
FIG. 2
AG250-003
Cold/Hot Potable Water
Electrical Valve
(battery operates)
Pass cable from the AG250-603 pedal through an
opening under the cabinet plate and connect it to the
AG250-003 valve installed inside the cabinet. (FIG.1)
Secure pedal to the floor by removing paperback from
adhesive pads on the bottom of the pedal (1) or secure
pedal using mounting screws (2). (FIG.2 )
1
2
2.
BOTTOM VIEW