Advantech PCM-3117 Installation and operation manual

PCM-3117StartupManual 1
PCM-3117 PCI to ISA Bridge Module
Startup Manual
The PCM-3117 is PCI to ISA bridge module.
For more and more PCI-104 bus application, there still
have PC104+ module customer used. For all modules can
be compatible, PCM-3117 is important solution. Except
this, PCM-3117 support two COM RS-232/422/485, user
can select the function by jumper setting.
But for OS limitation, user must install PCM-3117 first,
then just can install OS; Or computer can not distinguish
PCM-3117.
Before you begin installing your card, please make sure
that the following materials have been shipped:
• 1 PCM-3117 module
• 1 Start-up manual
• 1 2 x COM port cable P/N: 1701200220
• 1 Signal CABLE 4P to 4P P/N: 1700001898
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
PCM-3117 PCI to ISA Bridge Module
• Compatible with PC/104 and PC/104+
• PCI-104 CPU module (PCM-3380) be able to control
PC/104 peripheral (ISA bus)
• Support 2 COM RS-232/422/485
• Support Windows NT 4.0, Windows 98/2000/XP/SE
• Controller: ITE IT8888F
• Bus: PC/104(ISA) and PC/104+(PCI)
• Plug & Play: Support Plug & Play automatic detection &
configuration
• PC/104 expansion: 104-pin and 120-pin 16/32-bit
PC104 /Plus module connector
• Operating Voltage: +5 V Only
• Power Consumption: +5 @ 70 mA (Typical)
• Size/Weight: 96 x 90 mm (3.8î x 3.5î). 90 g (0.198 lb)
• Environment: 0 ~ 60× C (operation), -40 ~ 85× (Stor-
age)
• Humidity: 0 ~ 90%
Introduction Features
Packing list
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the PCM-3117
Part No. 2006311701 2nd Edition
Dec. 2005
Specifications
PCM-3117 PCI to ISA Bridge ModuleC

2 PCM-3117 Startup Manual
Board Dimensions Locating Connector and Jumpers
COM port RS232/422/485 jumper setting
Mechanical Drawings
Jumper Settings
Jumper setting
JP1: RS232/422/485 jumper setting of COM1
RS232 RS422 RS485
JP1(5-6) JP1(3-4) JP1(1-2)
JP1(7-9) JP1(9-11) JP1(9-11)
JP1(8-10) JP1(10-12) JP1(10-12)
JP1(13-15) JP1(15-17) JP1(15-17)
JP1(14-16) JP1(16-18) JP1(16-18)
JP2: RS232/422/485 jumper setting of COM2
RS232 RS422 RS485
JP2(5-6) JP2(3-4) JP2(1-2)
JP2(7-9) JP2(9-11) JP2(9-11)
JP2(8-10) JP2(10-12) JP2(10-12)
JP2(13-15) JP2(15-17) JP2(15-17)
JP2(14-16) JP2(16-18) JP2(16-18)
Connectors and Jumpers
Connector table
CN1A: PC104 plus
CN1A PCI Interface signal
CN1B: PC104
CN1B ISA Interface signal
CN2: COM Port
CN2 Connector of COM
CN3: Extended of several signals

PCM-3117 Startup Manual 3
CN3 Pin1: PCI_ISANOGO#
Pin2: PCI_ISAGNT#
Pin3: PCI_ISAREQ#
Pin4: LPC_SERIRQ
Note: User must use 1700001898 on CN3 of PCM-3117 to connect with CN20 of PCM-3380F A2 version, this will
be the cable for some ISA signal. Because the PCM-3380 A2 version just add the CN20, PCM-3117 must use for
PCM-3380/3386 A2 version.