Air Lift LoadLifter 5000 Series User manual

Kits 57288 |88288 |89288
For maximum effectiveness and safety, please read these instructions
completely before proceeding with installation.
Installation
Guide
MN-1085 • (011810) • ERN 9073 Failure to read these instructions can result in an incorrect installation.
GM Silverado/Sierra 1500
SERIES
Kits 57388 |88388 |89388
GM Trail Boss/Sierra AT4

IDENTIFYING THE DIFFERENCES BETWEEN KITS
Should you need to contact Air Lift customer service, you will need to know which kit you are inquiring about:
standard LoadLifter 5000, LoadLifter 5000 Ultimate or LoadLifter 5000 Ultimate Plus. The kits are easily
identifiable by looking at the roll plates and air lines.
 Standard LoadLifter 5000 — Zinc-plated steel roll plates and black nylon air lines.
 LoadLifter 5000 Ultimate — Black powder-coated roll plates and black nylon air lines.
 LoadLifter 5000 Ultimate Plus — Stainless steel roll plates, braided stainless steel air lines, stainless steel
air spring mounting hardware.
Air Lift offers two Ultimate Plus upgrade kits:
52300 - Braided stainless steel air line and fittings.
52301 - Stainless steel roll plates, air spring mounting hardware, braided stainless steel air lines and fittings.
LoadLifter 5000 Ultimate
black powder-coated
roll plate
LoadLifter 5000 Ultimate Plus
stainless steel
roll plate
LoadLifter 5000
silver zinc-plated steel
roll plate
LoadLifter 5000 Ultimate
nylon air line
LoadLifter 5000 Ultimate PLUS
braided stainless steel air line
LoadLifter 5000
nylon air line

TABLE OF CONTENTS
A. Installation Diagram ................................ 2
B. Hardware and Tools Lists ........................... 3
C. Introduction ....................................... 4
Notation Explanation ...................................................4
D. Installing the LoadLifter 5000 Series System............ 5
Getting Started ........................................................5
Assembling the Air Springs ..............................................7
Installing the Air Springs.................................................8
Attaching the Upper Brackets ............................................8
E. Installing the Air Lines ..............................10
Installing Nylon Air Lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing Braided Stainless Steel Air Lines..................................11
F. Finished Installation ................................12
Installation Checklist...................................................13
Maintenance and Use Guidelines.........................................13
Minimum and Maximum Air Pressure......................................13
Limited Warranty and Return Policy .......................................13

LoadLifter 5000 Series
MN-1085
2
A. Installation Diagram
I
A
F
O
B
D
N
N
C
S
F
V
U
N
T
R
E
P*
P*
g. A.1
* Optional hardware for vehicles equipped with
fifth-wheel hitches that have frame side plates
(see page 9 for details)
NOTE: If the truck has fifth-wheel
hitch brackets along the side of the
frame, these U-bolts may not be used.

LoadLifter 5000 Series
MN-1085 3
B. Hardware and Tools Lists
TOOLS LIST
KIT 57288 &
57388
KIT 88288 &
88388
KIT 89288 &
89388
Item Part# Description ........................................................ Qty
A 07856 Upper bracket (GM 1500) ....................................... 2
A 07388 Upper bracket (Trail Boss)....................................... 2
B 03156 Lower bracket ......................................................... 2
C 01656 Forward clamp bracket........................................... 2
D 01646 Rear clamp bracket................................................. 2
G 01615 Brake line tab bracket............................................. 2
H 13964 Spacer..................................................................... 2
I 11456 U-bolt 3/8"-16 x 6 1/2” .......................................... 4
J 17496 M8 -1.5 x 20 Hex head cap screw.......................... 2
K 17414 M8 -1.25 x 50 Hex head cap screw........................ 2
L 18501 M8 stainless steel flat washer................................. 4
M 18522 M8 x 1.25 Nylon lock nut ........................................ 2
N 18422 3/8”-16 Serrated flange lock nut........................... 14
O 17277 3/8”-16 x 3" Carriage bolt....................................... 6
P 17129 3/8” x 1" Thread cutting screw ............................... 4
W 10466 Zip ties .................................................................... 6
X 18411 5/16” Lock washer .................................................. 2
Common Parts Included in All 3 Kits
Item Part# Description ........................................................ Qty
E 58494 Air spring with jounce bumper ................................ 2
F 11967 Roll plate (black powder coated) ............................ 4
Q 20086 Air line assembly ..................................................... 1
R 21837 90° Swivel elbow fitting........................................... 2
S 17215 3/8”-24 x 3/4” Flat head socket cap screw ............ 4
T 17203 3/8”-24 x 7/8” Hex head cap screw........................ 4
U 18427 3/8” Split lock washer ............................................. 4
V 18444 3/8” Flat washer...................................................... 4
Y 21230 Valve cap................................................................. 2
Z 21233 5/16”-32 Hex nut..................................................... 4
AA 21234 Rubber washer........................................................ 2
BB 18501 Flat washer.............................................................. 2
Item Part# Description ........................................................ Qty
E 58439 Air spring................................................................. 2
F 11951 Roll plate (silver zinc plated) ................................... 4
Q 20086 Air line assembly ..................................................... 1
R 21837 90° Swivel elbow fitting........................................... 2
S 17215 3/8”-24 x 3/4” Flat head socket cap screw ............ 4
T 17203 3/8”-24 x 7/8” Hex head cap screw........................ 4
U 18427 3/8” Split Lock washer............................................ 4
V 18444 3/8” Flat washer...................................................... 4
Y 21230 Valve cap................................................................. 2
Z 21233 5/16”-32 Hex nut..................................................... 4
AA 21234 Rubber washer........................................................ 2
BB 18501 Flat washer.............................................................. 2
Unique Parts in Each Kit
The photos in this manual show the LoadLifter 5000 Ultimate kit.
Item Part# Description ........................................................ Qty
E 58494 Air spring with jounce bumper ................................ 2
F 11880 Roll plate (stainless steel)........................................ 4
CC 20987 Stainless steel braided air line ................................ 2
Q 20084 Air line assembly ..................................................... 1
R 21815 AN-type fitting......................................................... 2
S 17363 3/8”- 24 x 3/4” Flat head socket cap screw ss....... 4
T 17284 3/8”- 24 x 7/8” Hex head cap screw ss.................. 4
U 18504 3/8” Split lock washer ss ........................................ 4
V 18507 3/8” Flat washer ss ................................................. 4
AA 21234 Rubber washer........................................................ 2
BB 18501 M8 Flat washer........................................................ 2
CC 21709 Schrader valve with cap & nut ................................ 2
DD 21813 AN to PTC fitting ..................................................... 2
Description............................................................................ Qty
Standard and metric open-end or box wrenches ................................... 2
Adjustable wrench................................................................................... 1
Ratchet with 10mm & 9/16” deep-well sockets ................................................1
3/8” Nut driver .........................................................................................1
T40 torx bit ..............................................................................................1
Torque wrench......................................................................................... 1
Standard and metric hex head wrenches ...............................................1
Hose cutter, razor blade, or sharp knife .................................................. 1
Hoist or floor jacks .................................................................................. 1
Safety stands...........................................................................................1
Safety glasses ......................................................................................... 1
Air compressor or compressed air source .............................................. 1
Spray bottle with dish soap/water solution............................................. 1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Missing or damaged parts? Call Air Lift customer
service at [phone] for a replacement part.
* These parts are not shown in the Installation Diagram (Fig. A.1).
Missing or damaged parts? Call Air Lift customer
service at [phone] for a replacement part.
STOP!

LoadLifter 5000 Series
MN-1085
4
C. Introduction
The purpose of this publication is to assist with the installation and maintenance of the
LoadLifter 5000 series air spring kits. All LoadLifter 5000 series kits utilize sturdy, reinforced,
commercial-grade single or double, depending on the kit, convolute bellows.
The air springs are manufactured like a tire with layers of rubber and cords that control
growth. LoadLifter 5000 kits provide up to 5,000 pounds (2,268kg) of load-leveling support
with air adjustability from 5-100 PSI (.34-7BAR).
It is important to read and understand the entire installation guide before beginning
installation or performing any maintenance, service or repair.
NOTATION EXPLANATION
Hazard notations appear in various locations in this publication. Information which is
highlighted by one of these notations must be observed to help minimize risk of personal
injury or possible improper installation which may render the vehicle unsafe. Notes are used
to help emphasize areas of procedural importance and provide helpful suggestions. The
following definitions explain the use of these notations as they appear throughout this guide.
INDICATES IMMEDIATE HAZARDS WHICH WILL RESULT IN SEVERE PERSONAL INJURY
OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN SEVERE
PERSONAL INJURY OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN DAMAGE TO
THE MACHINE OR MINOR PERSONAL INJURY.
DANGER
CAUTION
WARNING
C. IntroductionC. Introduction

LoadLifter 5000 Series
MN-1085 5
D. Installing the LoadLifter 5000 Series System
g. D.1
g. D.3g. D.2
g. D.5g. D.4
Factory
bolts
H
K
L
Jounce
bumper
Jounce bumper removed
GETTING STARTED
1. Raise and support the vehicle in a way, using safety stands or equivalent, that the
axle can be safely dropped away from the frame. This will need to be done for the air
spring assembly to be put into position between the axles and frame (Fig. D.1).
2. Remove the factory bolts that hold the upper brake line bracket in place. Reattach
the bracket using the two new M8-1.25 x 50 hex head cap screws (K), two new M8
flat washers (L), and two new spacers (H) (Figs. D.2 & D.3). Torque bolts to 10 lb.-ft.
(14Nm).
3. Locate the jounce bumpers. Using a 10mm deep socket, remove the jounce bumpers
(both sides) and discard (Figs. D.4 & D.5).

LoadLifter 5000 Series
MN-1085
6
Ensure the
two Torx
head screws
on both wire
harness
guards were
removed (see
Step 4)
g. D.10g. D.9
g. D.8g. D.7
Brake line
bracket
Factory
bolts
J, L
& M
G
C
C
g. D.6
Passenger's (Right) Side
4. Using a T40 sized Torx bit, remove the two outer most Torx head screws on both wire
harness guards, located on the front side of the axle (Fig D.6).
5. Remove the brake line bracket attached to the axle under the leaf spring on both
sides of the vehicle. Set bolt aside for reinstallation.
6. Attach the brake line tab bracket (G) using the factory hardware previously removed
and tighten securely on both sides of the vehicle (Figs. D.7 & D.8).
7. Attach the brake line bracket to the brake line tab bracket using M8 hardware (J, L &
M) on both sides of the vehicle (Fig. D.8). Torque bolts to 16 lb.-ft. (22Nm).
8. Position the forward clamp bracket (C) on the front side of the axle (Figs. D.9 & D.10).

LoadLifter 5000 Series
MN-1085 7
LEFT
g. D.11
RIGHT
OO
Ensure
fitting is
less than
7/8" in
height
g. D.15
T
U
V
g. D.13 g. D.14
ASSEMBLING THE AIR SPRINGS
1. Place a 3/8"-16 x 3"carriage bolt (O) through the inner most square hole on the rear
side of each lower bracket (B) (Fig. D.11).
The radiused (rounded) edge of the roll plate (F) will be toward the air spring so that the air
spring is seated inside the roll plate.
2. Install a lower bracket (B) and roll plate (F) on each air spring (E) using two 3/8"-24
x 3/4" flat head socket cap screws (S) through the innermost mounting holes (Fig.
D.12). Torque the flathead screws to no more than 20 lb.-ft. (27Nm) (Fig. D.12).
3. Install the 90 degree swivel elbow fitting (R) into the top of each air spring finger tight.
Tighten the swivel fittings an additional one and a half turns (Fig. D.12).
4. Attach the upper roll plates (F) and upper brackets (A) to the air springs (E) using two
3/8"-24 x 7/8" bolts (T), two 3/8" lock washers (U) and two 3/8" flat washers (V) for
each assembly (Fig. D.13). Torque bolts to no more than 20 lb.-ft. (27Nm). These
brackets are not left or right hand specific (Fig. D.14).
5. With the bracket installed, ensure the swivel fitting is less than 7/8" in height, and if
not, tighten the fitting until this height is achieved (Fig. D.15).
BB
R
g. D.12
O
F
E
NOTE

LoadLifter 5000 Series
MN-1085
8
CAUTION
g. D.17g. D.16
B
CO
B
Rear View
Front View
N
O
D
g. D.18
I
INSTALLING THE AIR SPRINGS
1. Drop the axle or raise the frame to make room to put the assemblies into position.
ENSURE VEHICLE IS PROPERLY SUPPORTED PRIOR TO BEGINNING INSTALLATION.
2. Place the assemblies on the lower strike plate with the fitting side of the assembly to
the outside (wheel side) of the vehicle. Align the tab on the forward clamp bracket (C)
with the hole on the front of the lower bracket (B) (Fig. D.16).
3. Insert two carriage bolts (O) on the front and rear square holes of the lower bracket
(B) (both sides) (Figs. D.16 & D.17).
4. Thread the 3/8" flange nuts (N) onto the carriage bolts previously installed. Ensure
the front and rear clamps align correctly under the axle jounce bumper strike plate.
Torque all flange nuts evenly to 16 lb.-ft. (22Nm).
ATTACHING THE UPPER BRACKETS
There are two ways to attach the upper bracket.
For trucks that do not have a fifth-wheel hitch bracket alongside the frame:
1. Place U-bolts (I) over the frame as pictured on both sides of the vehicle (Fig. D.18).

LoadLifter 5000 Series
MN-1085 9
2. Lower the vehicle or raise the axle while inserting the threaded portions of the U-bolts
(I) through the corresponding holes in the upper brackets (A). Install flange nuts (N)
finger tight (Fig. D.19).
3. Adjust the upper bracket (A) as needed to veritcally align the air spring with the frame
(or as close to perpendicular as possible).
4. Torque all flange nuts (N) to 16 lb.-ft. (27Nm).
For trucks that have fifth-wheel hitch brackets alongside the frame rail:
1. There are holes in the middle of the bracket just forward and behind the jounce
bumper mounting cups on the upper bracket (Fig. A.1). Once the upper brackets are
in position, drill two 5/16” holes through the bottom of the frame using the holes as a
template and attach the upper brackets using the self-tapping screws (P). Torque all
four fasteners to 15 lb.-ft. (20Nm).
2. Reattach the wire harness guards on the front side of the axle. Tighten securely
(Fig. D.20).
g. D.19
N
I
A
g. D.20
Passenger's (Right) Side

LoadLifter 5000 Series
MN-1085
10
E. Installing the Air Lines
Air lines are routed
from the air springs
to Schrader valves.
LoadLifter 5000
series air lines
come in two styles:
nylon and braided
stainless steel.
Begin by choosing
locations for the
Schrader valves and
drill a 5/16” (8mm)
hole, if necessary
(Fig. E.1).
KEEP AT LEAST 6” (150MM) OF CLEARANCE BETWEEN ALL AIR LINES AND THE
EXHAUST SYSTEM. AVOID SHARP BENDS AND EDGES.
INSTALLING NYLON AIR LINES
1. Cut the air line in half. Make clean, square cuts with a razor blade or hose cutter
(Fig. E.2). Do not use scissors or wire cutters.
2. Use zip ties to secure the air line to fixed points along the chassis. Do not pinch or kink
the air line. The minimum bend radius for the air line is 1 ” (25mm) . Leave at least 2”
(50mm) of slack in the air line to allow for any movement that might pull on the air line.
3. Install the Schrader valve in the chosen location (Fig. E.3).
Good cut Bad cut
A. Inside fuel tank filler door C. License plate or
B. Inside rear wheel wells rear bumper area
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
A. B. C.
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
If a location for the Schrader valve other than the back of
the vehicle is chosen, it may be necessary to coil the
excess air line. The braided stainless steel air line cannot
be trimmed.
A. Inside fuel
tank filler
door
B. Inside rear
wheel wells
C. License
plate or rear
bumper area*
* For LoadLifter 5000 Ultimate Plus kits, the recommended location
for the Schrader valves is the rear bumper area or license plate.
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
A. B. C.
USE IN
Standard,
Ultimate,
7500XL
USE IN
Plus
upgrade kit
USE IN
Plus combo
manuals
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
If a location for the Schrader valve other than the back of the vehicle is
chosen, it may be necessary to coil the excess air line. The braided
stainless steel air line cannot be trimmed.
USE IN
Plus
upgrade kit
Hex nuts
Star washer
Rubber washer
Air Line Setup for Compressor Integration
Air Line Setup Without Compressor System
Vehicle body
or bumper
Hex nuts
Flat washer
Star washer
Rubber washer
Nylon air line
to compressor
system and
Schrader valve
Flat
Flat
Vehicle body
or bumper
Braided stainless steel
air line to air spring
5/16” (8mm)
hole
AN to PTC
fitting
Schrader
valve
Vehicle
body or
bumper
AN
Schrader
valve Air line hex nut
Flat washer
Nylon air line
to air spring
5/16” (8mm) hole
Braided
stainless
steel air line
to air spring
Hex nuts
Flat washer
Star washer
Rubber washer
Schrader
valve
Vehicle
body or
bumper
Nylon air line
to air spring
5/16” (8mm) hole
g. E.2
g. E.3
g. E.1
CAUTION

LoadLifter 5000 Series
MN-1085 11
INSTALLING BRAIDED STAINLESS STEEL AIR LINES
KEEP THE AIR LINE AWAY FROM THE FUEL LINE, BRAKE LINES AND ELECTRICAL
WIRES.
1. Use zip ties to secure
the air line to fixed points
along the chassis every
6” to 8” (150-200mm).
Leave at least 2” (50mm)
of slack to allow for any
movement that might pull
on the air line.
2. Tighten the air line hex
nut finger tight, then use
2 wrenches to turn
1 additional flat (1/6
of one full turn). Do
not overtighten
(Figs. E.4 or E.5). The
easiest way to tighten the
fitting is off the vehicle.
Install the Schrader valve
in the chosen location.
3. Coil and secure any
excess air line in an
area where it will not be
susceptible to damage.
The braided stainless
steel air line cannot be trimmed.
Hex nuts
Star washer
Rubber washer
Air Line Setup for Compressor Integration
Air Line Setup Without Compressor System
Vehicle body
or bumper
Hex nuts
Flat washer
Star washer
Rubber washer
Nylon air line
to compressor
system and
Schrader valve
Flat
Flat
Vehicle body
or bumper
Braided stainless steel
air line to air spring
5/16” (8mm)
hole
AN to PTC
fitting
Schrader
valve
Vehicle
body or
bumper
AN
Schrader
valve Air line hex nut
Flat washer
Nylon air line
to air spring
5/16” (8mm) hole
Braided
stainless
steel air line
to air spring
Hex nuts
Flat washer
Star washer
Rubber washer
Schrader
valve
Vehicle
body or
bumper
Nylon air line
to air spring
5/16” (8mm) hole
g. E.4
g. E.5
CAUTION

LoadLifter 5000 Series
MN-1085
12
Driver's (left)
side view.
Passenger's
(right) side
view.
1. The images show the finished installation of both sides (Figs. F.1, F.2, F.3 & F.4).
Finished installation images show the LoadLifter 5000 Ultimate Plus kit installed.
F. Finished Installation
g. F.1 g. F.2
Driver's (left)
side view.
Passenger's
(right) side
view.
g. F.3 g. F.4
NOTE

LoadLifter 5000 Series
MN-1085 13
Maintenance and Use Guidelines
1. Check air pressure weekly.
2. Always maintain normal ride height. Never inflate beyond 100 PSI (7BAR).
3. If the system develops an air leak, use a soapy water solution to check all air line
connections and the inflation valve core before deflating and removing the air spring.
FOR SAFETY AND TO PREVENT POSSIBLE DAMAGE TO THE VEHICLE, DO NOT EXCEED
MAXIMUM GROSS VEHICLE WEIGHT RATING (GVWR) OR PAYLOAD RATING, AS
INDICATED BY THE VEHICLE MANUFACTURER.
ALTHOUGH THE AIR SPRINGS ARE RATED AT A MAXIMUM INFLATION PRESSURE OF
100 PSI (7BAR), THE AIR PRESSURE ACTUALLY NEEDED IS DEPENDENT ON LOAD AND
GROSS VEHICLE WEIGHT RATING.
Maximum Air PressureMinimum Recommended Pressure
100 PSI (7BAR)5 PSI (.34BAR)
Clearance test — Inflate the air springs to 40-60 PSI (2.8-4.1BAR) and make sure
there is at least 1/2” (13mm) clearance from anything that might rub against each
sleeve. Be sure to check the tire, brakes, frame, shock absorbers and brake cables.
Leak test before road test — Inflate the air springs to 40-60 PSI (2.8-4.1BAR) and
check all connections for leaks. All leaks must be eliminated before the vehicle is
road tested.
Heat test — Be sure there is sufficient clearance from heat sources, at least 6” (152mm)
for air springs and air lines. If a heat shield was included in the kit, install it. If there is no
heat shield, but one is required, call Air Lift customer service at [phone].
Fastener test — Recheck all bolts for proper torque.
Road test — The vehicle should be road tested after the preceding tests. Inflate the
springs to recommended driving pressures. Drive the vehicle 10 miles (16km) and
recheck for clearance, loose fasteners and air leaks.
Operating instructions — If professionally installed, the installer should review the
operating instructions with the owner. Be sure to provide the owner with all of the
paperwork that came with the kit.
INSTALLATION CHECKLIST
CAUTION
CAUTION
Limited Warranty and Return Policy
Air Lift Company provides a limited lifetime warranty to the original purchaser of its load support
products, that the products will be free from defects in workmanship and materials when used
on cars and trucks as specified by Air Lift Company and under normal operating conditions,
subject to the requirements and exclusions set forth in the full Limited Warranty and Return
Policy that is available at www.airliftcompany.com/warranty.
For additional warranty information contact Air Lift Company customer service.

Need Help?
Contact Air Lift Company customer service department by calling (800)
248-0892.
For calls from outside the USA or Canada,
dial [phone].
Need Help?
Contact Air Lift Company Customer Service at [phone]
or email [e-mail].
For calls outside the U.S. or Canada, dial [phone].
JJC-1018
Thank you for purchasing Air Lift Products — the Authorized Installer's choice!
Air Lift Company • 2727 Snow Road • Lansing, MI 48917 or P.O. Box 80167 • Lansing, MI 48908-0167
Printed in the USA
California: WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Air Lift Company reserves the right to make changes and improvements to its products and publications at any time.
For the latest version of this manual, contact Air Lift Company at [phone] or visit airliftcompany.com.