Air Monitor Corporation VOLU-flo / OAM Operating and maintenance manual

VOLU-flo / OAM Station
INSTALLATIONPROCEDURE
WARRANTY
AirMonitorCorporation(hereinafterreferredtoas"Seller")warrantsthatatthetimeofshipment,productssold
pursuant to this contract will be free from defects in materials and workmanship, and will conform to the
specificationsfurnishedorapprovedinwritingbySeller.Nowarrantyisgiventhatdeliveredproductswillconform
to catalog sheets, data sheets, and the like, which are subject to change without notice.
Sellerwillrepairorreplace,atitsoption,anyproductslistedunderthiswarrantywhichisreturnedfreightpre-
paidtoSellerandwithintheearlierofone(1)yearafterstart-uporfifteen(15)monthsaftershipment,proveupon
testandexaminationbySellertobedefectivewithinthetermsofthiswarranty. Thewarrantyperiodforanyitem
repairedorreplacedshallbeforthetimeremainingonthewarrantyperiodfortheoriginalcomponents. Purchaser
shall notify Seller in writing of such defect within sixty (60) days of discovery of the defect.
This warranty does not extend to any product sold by Seller which has been the subject of misuse, neglect,
accident,damageormalfunctioncausedbyinterconnectionwithequipmentmanufacturedbyothers,improper
installationorstorage,orusedinviolationofinstructionsfurnishedbySeller,nordoesitextendtoanyproduct
which has been repaired or altered by persons not expressly approved by Seller. Nor does Seller warrant
equipmentagainstnormaldeteriorationduetoenvironment;noritemssuchasthermocouples,electrodes,and
similaritemssubjecttowearorburnoutthroughusage. Adjustmentsforitemsorequipmentnotmanufactured
bySellershallbemadetotheextentofanywarrantyofthemanufacturerorsupplierthereof.Sellershallnotbe
liableforanyspecialorconsequentialdamagesorforlossofdamagedirectlyorindirectlyarisingfromtheuse
oftheproducts. Seller'swarranty shallbelimitedtoreplacementofdefectiveequipmentandshallnotinclude
fieldremovalandinstallationexpenses.
Thewarrantysetforthaboveisinlieuofallotherwarrantieseitherexpressorimpliedandconstitutesthefullextent
ofAirMonitorCorporation'sliabilitytothecustomer,oranyotherpartyforbreachofwarranty. THEREARENO
EXPRESSWARRANTIESEXCEPTASSETFORTHHEREIN. THEREARENOIMPLIEDWARRANTIESOF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, WHICH ARE PARTICULARLY
DISCLAIMED.
INSPECTION&HANDLING.
VOLU-flo/OAMstationsshould be carefully inspected for damage prior to installation. Report damage to your Freight
Department,orcontactthedelivery carrier.
Almost any means of handling can be utilized depending on the length and weight of the station. Stations may
be handled while in any position. However, it is important not to drop or mishandle a station such that damage is
done to the expanded metal screen, sensors, signal connection fittings, or flanges.

VOLU-flo / OAM Station
ORIENTATION OF STATION. Using theAIRFLOW directional arrow on the side of the station to determine correct
orientation,installthe station with the outsidereference sensor facing airflow.
CAUTION: VOLU-flo/OAMstations should not be used to strengthen or support connecting ductwork,
andholes should not be drilled into thecasing otherthan throughconnecting flanges.
FASTENERS. The VOLU-flo/OAM station can be attached to adjacent ductwork by means of its 90º connection
flanges. Connection flanges are not pre-drilled, allowing the installer a choice of fastener types, sizes, and spacing
consistent with similar elements in the ductwork and standard industry practices, to ensure an airtight installation.
SIGNAL TUBING. Signal tubing connections may be 1/4" OD if the distance from the measuring device to the
transmitter is 200' or less.
CAUTION: External fittings on the VOLU-flo/OAM station must not be rotated or twisted during
installation of connection fittings. After tubing is completed, signal lines should be leak
tested prior to operation.
TEMPERATURE SENSOR. Connect the RTD temperature probe wires as follows:
Terminal on
OAMStation
White
Red (either)
Red (either)
Terminal on
VOLU-flo/OAM
Module
1 (Ra)
2 (Rb)
3 (Rb)
REMOTE RTD
STATION MOUNTED RTD
- 2 -

VOLU-flo / OAM Station
-3-
STATION CONFIGURATION.
SPLIT STATION INSTALLATION. Units larger than 120” in height or width are split for shipment and require field
assembly. Assembly hardware is provided.

VOLU-flo / OAM Station
-4-
DUCTED INSTALLATION AIR HANDLER INSTALLATION
CUSTOMER SERVICE. AirMonitorCorporation provides in-house technical support for all our products:
Monday through Friday, 7 am to 5 pm (pst)
Phone:[phone]or 1-800-AIRFLOW
Fax:[phone]
If after contacting the Customer Service Department it is determined that equipment will require return toAir Monitor
Corporationfor further repair,a ReturnAuthorizationnumber will be issued.
AConfirmation of ReturnAuthorization with shipping instructions will be sent via facsimile or e-mail. Equipment to be
returned to Air Monitor should be returned in its original shipping container if possible. If this is not possible, ensure
equipment is packaged sufficiently to protect it during shipment.
Caution: All damage occurring during transit is the Customer’s responsibility.
List the Return Authorization (R/A) number on the packing list and clearly mark this number on the outside of each
shipping container. Costs associated with the return of equipment to Air Monitor Corporation are the customer’s
responsibilityregardless whether the repair/return is underwarranty.
Once the Customer Service Department determines that the equipment repair is under warranty, the item will be
repaired and returned to the customer at no charge. If the equipment is not under warranty, customer will need to
approvea repair quote which willbeinvoiced along with return shippingcharges.
1050 Hopper Avenue • Santa Rosa, CA 95403 • 707-544-2706
www.airmonitor.com
INSTALL41A,Rev.(10-13)