Aircat 1994 User manual

MODEL: 1994
1" x 8" "SUPER DUTY" IMPACT WRENCH

Model No. Free Speed
(RPM)
Bolt Capacity
(in.)
Square
Drive
(in.)
Impacts Per
Minute
Max. Torque
(ft-lb) @90 psi
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
1994 4,500 1-1/4 1 x 8 1100 2300 35.0 26.0 16 1/2 3/8 NPT
SPECIFICATIONS
Important Warnings - Impacts
1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact
driver.
2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring
and pin should be used to prevent the socket falling off and causing injury.
3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool
damage and replace when necessary.
Accessory Hazards
4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply

MODEL: 1994
1" x 8" "SUPER DUTY" IMPACT WRENCH
Exploded View & Parts List
Ref. Part No. Description Qty Description Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Hexagonal Screw
Washer
Hammer Case
D-type Handle
Gasket
Oil Seal
Anvil Bushing
Retaining Ring
Anvil
Hammer Bushing
Hammer Dog
Cam
Hammer Cage
Bearing
Motor Housing
Bearing
Front End Plate
Rotor Blade
Rotor
Pin
Cylinder
4
8
1
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
6
1
2
1
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Rear End Plate
Gasket
Back Handle
Regulator Pin
Valve Bushing
Throttle Valve Bushing
Regulator Body
Steel Ball
Spring
O ring
Spring
O ring
Air Inlet
Air Inlet Screen
Spring Pin
Trigger Pin
Trigger - Inside
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
25
26
Ref. Part No.
979401-1
979402-1
979403-1
979404-1
979405-1
979406-1
979407-1
979408-1
979409-1
979410-1
979411-1
979412-1
979413-1
979414-1
979415-1
979416-1
979417-1
979418-1
979419-1
979420-1
979421-1
979422-1
979423-1
979424-1
979425-1
979426-1
979427-1
979428-1
979429-1
979430-1
979431-1
979432-1
979433-1
979434-1
979435-1
979436-1
979437-1
979438-1
979439-1
979440-1
979441-1
979442-1
979443-1
979444-1
979445-1
979446-1
979447-1
Hexagonal Screw
Washer
O ring
Hexagonal Screw
Washer
Throttle ValvePin
Throttle Valve
Hose Connector
Hexagonal Screw
R
e
f
.
P
a
r
t
r
r
N
o
.
D
e
s
c
r
i
p
t
i
o
n
Q
t
y
D
e
s
c
r
i
p
t
i
o
n
Q
ty
R
e
f
.
P
a
r
t
r
r
N
o
.
123
4
5
6
78910 11 12
13 14 15 16
17 18 19 20 22
21
23 24 25
19
26 27 28
29 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47

SERVICE CENTER LISTINGS ENCLOSED
AIRCAT and NITROCAT air tools are warranted to be free from defects in material and workmanship for 2 years from date
of purchase. We will repair or replace; at our option any defective part or unit which proves to be defective in material or
workmanship during this 2 year period. The foregoing obligation is AIRCAT and Florida Pneumatic's sole liability under this
or any implied warranty, under no circumstances shall it be liable for any incidental or consequential damages.
This warranty applies to the tool only. The warranty does not apply to any attached accessories/consumable products;
such as drill chucks, sander backing pads, air hammer retainers and chisels or “kit” accessories or any other accessory
included with the tool.
an AIRCAT or Florida Pneumatic Authorized Service Center) are not covered by this warranty.
Return your tool to an AIRCAT or Florida Pneumatic Authorized Service Center freight prepaid. Be sure to include your
name, address, copy of purchase with date and description of the suspected defect.
AIRCAT whose policy is continued product improvement reserves the right to make changes in design or construction at
any time without incurring any obligation on tools previously sold.
Tune-Up and Head Kits for all AIRCAT PNEUMATIC impact wrenches and ratchets are available.
For Authorized Service Centers, please visit www.aircat.com/warranty-service